Add OOB layout description for docg3, so that userspace can
use this information to setup the data for write_oob().
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: NIvan Djelic <ivan.djelic@parrot.com>
Reviewed-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add support for multiple floors, ie. cascaded docg3
chips. There might be 4 docg3 chips cascaded, sharing the
same address space, and providing up to 4 times the storage
capacity of a unique chip.

Each floor will be seen as an independant mtd device.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: NIvan Djelic <ivan.djelic@parrot.com>
Reviewed-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Fix the docg3 reads to be able to cope with all possible
data buffer / oob buffer / file mode combinations from
docg3_read_oob().
This especially ensures that raw reads do not use ECC
corrections, and AUTOOOB and PLACEOOB do use ECC
correction.

The approach is to empty docg3_read() and make it a wrapper
to docg3_read_oob(). As docg3_read_oob() handles all the
funny cases (no data buffer but oob buffer, data buffer but
no oob buffer, ...), docg3_read() is just a special use of
docg3_read_oob().
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: NIvan Djelic <ivan.djelic@parrot.com>
Reviewed-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

BCH registers are contiguous, not on every byte. Fix the
register definitions.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: NIvan Djelic <ivan.djelic@parrot.com>
Reviewed-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The protection areas boundaries were on 16bit registers, not
8bit. This is consistent with block numbers, which can
extend up to 4096 on bigger chips (and is 2048 on the
docg3).
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: NIvan Djelic <ivan.djelic@parrot.com>
Reviewed-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Writeb was incorrectly traced as a 16 bits write, instead of
a 8 bits write. Fix it by tracing the correct width.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: NIvan Djelic <ivan.djelic@parrot.com>
Reviewed-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Change the NOP debug log verbosity to very verbose to
unburden log analysis.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: NIvan Djelic <ivan.djelic@parrot.com>
Reviewed-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Depending on whether MTD_DOCPROBE_ADVANCED is set or not,
MTD_DOCPROBE_ADDRESS will default to either 0x0000 or 0. That should
lead to (basically) identical code in docprobe.c. The current two
defaults should be merged.

And, while we're at it, if MTD_DOCPROBE is set MTD_DOCPROBE_ADDRESS will
always be set. (MTD_DOCPROBE_ADDRESS depends on MTD_DOCPROBE and it has
a default value.) So the check whether CONFIG_MTD_DOCPROBE_ADDRESS is
defined is unnecessary and should be dropped.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

On some platforms such as P3060QDS, has multiple spi flashes, but they are
not available at same time, so if their status is 'disabled', which is set
by u-boot, will not be probed.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Add support for DiskOnChip G3 chips. The support is quite
limited yet :
 - no flash writes/erases are implemented
 - ECC fixes are not implemented
 - powerdown is not implemented
 - IPL handling is not yet done

On the brighter side, the chip reading does work.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>

Add support for EON spi flash EN25Q32B, which is not listed in id table,
need to add it in the id table to support the EON flash.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@intel.com>

Signed-off-by: NMikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@intel.com>

These modes are not necessarily for OOB only. Particularly, MTD_OOB_RAW
affected operations on in-band page data as well. To clarify these
options and to emphasize that their effect is applied per-operation, we
change the primary prefix to MTD_OPS_.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@intel.com>

Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@intel.com>

Start moving away from the MTD_DEBUG_LEVEL messages. The dynamic
debugging feature is a generic kernel feature that provides more
flexibility.

(See Documentation/dynamic-debug-howto.txt)

Also fix some punctuation, indentation, and capitalization that went
along with the affected lines.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@intel.com>

It adds device tree probe support for mtd_dataflash driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@intel.com>

Therefor -> Therefore
[Intern], [Internal] -> [INTERN]
[REPLACABLE] -> [REPLACEABLE]
syndrom, syndom -> syndrome
ecc -> ECC
buswith -> buswidth
endianess -> endianness
dont -> don't
occures -> occurs
independend -> independent
wihin -> within
erease -> erase
blockes -> blocks
...
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NArtem Bityutskiy <dedekind1@gmail.com>

Convert the driver to use ofpart partitions parsing through the generic
parse_mtd_partitions().
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NArtem Bityutskiy <dedekind1@gmail.com>

Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Replace custom invocations of parse_mtd_partitions and mtd_device_register
with common mtd_device_parse_register call. This would bring: standard
handling of all errors, fallback to default partitions, etc.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Consolidate knowledge about partitions in drivers/mtd/devices/lart.c.
Drop all HAVE_PARTITIONS conditionals. Always use partitioning.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

Since 'cmdline, NULL' is now a default for parse_mtd_partitions, don't specify
this in every driver, instead pass NULL to force parse_mtd_partitions
to use default.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>

I no longer work at Bluewater Systems. Update my email address accordingly. I
have deleted my email address from C files rather than change it. This
was suggested by several people, since the commit from my new email
address will cause scripts/get_maintainer.pl to function properly. I
have not added the .mailmap entry as suggested by Joe because I think
it is no longer necessary if I touch all the files which had my name
in them.
Signed-off-by: NRyan Mallon <rmallon@gmail.com>
Cc: Andre Renaud <andre@bluewatersys.com>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: trivial@kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The older add_mtd_device()/add_mtd_partitions() and their removal
counterparts will soon be gone.  Replace uses with mtd_device_register()
and mtd_device_unregister().
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Convert to mtd_device_register() and remove the check for
mtd_has_partitions() as we always have partitioning enabled now.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The previous section mismatch fix for this driver wasn't entirely correct.
The sst25l_flash_info array is now used in the devinit probe func, but is
marked as initdata, so building results in the warning:

WARNING: drivers/mtd/devices/sst25l.o(.devinit.text): Section mismatch
	in reference from the function sst25l_probe()
	to the variable .init.data:sst25l_flash_info

Further, the remove func should be devexit rather than exit to match the
probe func.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

S25FL512S = 64MiB single die, same family as S25FL256S
S70FL01GS = 2x S25FL512S dies in one package (separate chip selects)

These devices are not sampling yet, but they are expected to be very
similar to S25FL256S, which has been tested.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

These are 32MiB parts which use a slightly different 4-byte enable
sequence from Macronix.

Default to the Spansion 4-byte scheme in set_4byte(), as it is more
likely to be copied by other vendors.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the manufacturer ID names from cfi.h instead of hard-coding
hex constants.  Introduce a JEDEC_MFR macro for clarity.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Commit 4f678a58 (mtd: fix memory leaks in phram_setup) missed two cases
where the memory allocated for name would be leaked. This commit frees
the memory when register_device() fails and on unregister_devices().
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Set the 'mtd->writebufsize' field to 64 to mimic modern CFI flashes.
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>