This patch adds initial support for mqprio rate limiters (max_rate only).

Atlantic HW supports Rate-Shaping for time-sensitive traffic at per
Traffic Class (TC) granularity.
Target rate is defined by:
* nominal link rate (always 10G);
* rate factor (ratio between nominal rate and max allowed).
Signed-off-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates TCVEC2RING to accept nic_cfg, which is needed to be able
to use it from hw_atl.
The name is updated to reflect the changes.
Signed-off-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for per-TC queue statistics.

By default (single TC), the output is the same as it used to be, e.g.:
     Queue[0] InPackets: 2
     Queue[0] OutPackets: 8
     Queue[0] Restarts: 0
     Queue[0] InJumboPackets: 0
     Queue[0] InLroPackets: 0
     Queue[0] InErrors: 0

If several TCs are enabled, then each queue statistics line is prefixed
with TC number, e.g.:
     TC0 Queue[0] InPackets: 6
     TC0 Queue[0] OutPackets: 11
Queue numbering is end-to-end, so:
     TC1 Queue[4] InPackets: 0
     TC1 Queue[4] OutPackets: 22
Signed-off-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds multi-TC support.

PTP is automatically disabled when the user enables more than 2 TCs,
otherwise traffic on TC2 won't quite work, because it's reserved for PTP.
Signed-off-by: NDmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: NDmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: NDmitry Bogdanov <dbogdanov@marvell.com>
Co-developed-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contains the following changes:
* add cfg->is_ptp (used for PTP enable/disable switch, which
  is described in more details below);
* add cfg->tc_mode (A1 supports 2 HW modes only);
* setup queue to TC mapping based on TC mode on A2;
* remove hw_tx_tc_mode_get / hw_rx_tc_mode_get hw_ops.

In the first generation of our hardware (A1), a whole traffic class is
consumed for PTP handling in FW (FW uses it to send the ptp data and to
send back timestamps).
The 'is_ptp' flag introduced in this patch will be used in to automatically
disable PTP when a conflicting configuration is detected, e.g. when
multiple TCs are enabled.
Signed-off-by: NDmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the PTP TC initialization into a separate function.
Signed-off-by: NDmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contains the following changes:
* access cfg via aq_nic_get_cfg() in aq_nic_start() and aq_nic_map_skb();
* call aq_nic_get_dev() just once in aq_nic_map_skb();
* move ring allocation/deallocation out of aq_vec_alloc()/aq_vec_free();
* add the missing aq_nic_deinit() in atl_resume_common();
* rename 'tcs' field to 'tcs_max' in aq_hw_caps_s to differentiate it from
  the 'tcs' field in aq_nic_cfg_s, which is used for the current number of
  TCs;
* update _TC_MAX defines to the actual number of supported TCs;
* move tx_tc_mode register defines slightly higher (just to keep the order
  of definitions);
* separate variables for TX/RX buff_size in hw_atl*_hw_qos_set();
* use AQ_HW_*_TC instead of hardcoded magic numbers;
* actually use the 'ret' value in aq_mdo_add_secy();
Signed-off-by: NDmitry Bezrukov <dbezrukov@marvell.com>
Co-developed-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NMark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make the function easier to identify as being part of the ice driver,
prepend ice to the function name.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Self-explanatory.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The variable status cannot be zero due to a prior check of it; remove this
check.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The else conditional expression is always true due to the if conditional
expression; remove it and add a comment to make it obvious still.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In function ice_set_mac_address, we will remove old dev_addr before
adding the new MAC. In the removing and adding process of the MAC,
there is no need to return error if the check finds the to-be-removed
dev_addr does not exist in the MAC filter list or the to-be-added mac
already exists, keep going or return success accordingly.
Signed-off-by: NLihong Yang <lihong.yang@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move filter functions to separate file.

Add functions that prepare suitable ice_fltr_info struct
depending on the filter type and add this struct to earlier created
list:
- ice_fltr_add_mac_to_list
- ice_fltr_add_vlan_to_list
- ice_fltr_add_eth_to_list
This functions are used in adding and removing filters.

Create wrappers for functions mentioned above that alloc list,
add suitable ice_fltr_info to it and call add or remove function.
- ice_fltr_prepare_mac
- ice_fltr_prepare_mac_and_broadcast
- ice_fltr_prepare_vlan
- ice_fltr_prepare_eth
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Memory allocated in the ice_add_prof_id_vsig() function wasn't being
properly freed if an error occurred inside the for-loop in the function.

In particular, 'p' wasn't being freed if an error occurred before it was
added to the resource list at the end of the for-loop.
Signed-off-by: NEric Joyner <eric.joyner@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The vf_id variable is dealt with in the code in inconsistent
ways of sign usage, preventing compilation with -Werror=sign-compare.
Fix this problem in the code by always treating vf_id as unsigned, since
there are no valid values of vf_id that are negative.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change min() macros to min_t() which has compare type specified and it
helps avoid precision loss.

In some cases there was precision loss during calls or assignments.
Some fields in structs were unnecessarily large and gave multiple
warnings.

There were also some minor type differences which are now fixed as well as
some cases where a simple cast was needed.

Callers were were passing data that is a u16 to
ice_sched_cfg_node_bw_alloc() but the function was truncating that to a u8.
Fix that by changing the function to take a u16.
Signed-off-by: NKarol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When printing the ice status or AQ error codes, instead of printing out the
numerical value, provide the description of the error code. This provides
more info about the issue than a number.
Signed-off-by: NLihong Yang <lihong.yang@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As soon as the driver registers the PF netdev, userspace utilities
like NetworkManager try to bring up the associated interface. When
this happens, the driver may not have finished initializing fully,
resulting in a bunch of errors in the interface up flow.

The driver already has a mechanism to indicate if it's not up yet;
by setting the __ICE_DOWN bit in pf->state, but this bit gets
cleared too early in the current flow. So clear this bit only when
the driver is fully up. Also check for the same bit in the ice_open
flow, and return -EBUSY if the bit is set.

Also in ice_open, replace references of vsi->back with a local
variable.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, the ice driver is setting a PHY configuration,
which causes a link drop, and then additionally it calls
for a nway_reset, which restarts auto-negotiation on the
link, which also causes a link drop.  These two link
events in such close timing is causing the FW to not be
able to generate a link interrupt for the driver to
respond to.

Remove the unnecessary auto-negotiation restart from the
set pauseparams flow.  Also remove error path that
would have performed an ice_down/ice_up as that is
also unnecessary.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current implementation for contiguous TC check
is assuming that the UPs will be mapped to TCs in
a linear progressing fashion.  This is obviously
not always true.

Change the check to allow for various UP2TC mapping
configurations.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When there's a Tx timeout for a queue which belongs to a PFC enabled TC,
then it's not because the queue is hung but because PFC is in action.

In PFC, peer sends a pause frame for a specified period of time when its
buffer threshold is exceeded (due to congestion). Netdev on the other
hand checks if ACK is received within a specified time for a TX packet, if
not, it'll invoke the tx_timeout routine.
Signed-off-by: NAvinash JD <avinash.dayanand@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement promiscuous support for VF VSIs. Behaviour of promiscuous support
is based on VF trust as well as the, introduced, vf-true-promisc flag.

A trusted VF with vf-true-promisc disabled will be the default VSI, which
means that all traffic without a matching destination MAC address in the
device's internal switch will be forwarded to this VF VSI.

A trusted VF with vf-true-promisc enabled will go into "true promiscuous
mode". This amounts to the VF receiving all ingress and egress traffic
that hits the device's internal switch.

An untrusted VF will only receive traffic destined for that VF.

The vf-true-promisc-support flag cannot be toggled while any VF is in
promiscuous mode. This flag should be set prior to loading the iavf driver
or spawning VF(s).
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Create a boost TCAM entry for each tunnel port in order to get a tunnel
PTYPE. Update netdev feature flags and implement the appropriate logic to
get and set values for hardware offloads.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The flash memory for the ice hardware contains a block of information
used for link management called the Netlist module.

As this essentially represents another section of firmware, add its
version information to the output of the driver's .info_get handler.

This includes both a version and the first few bytes of a hash of the
module contents.

  fw.netlist -> the version information extracted from the netlist module
  fw.netlist.build-> first 4 bytes of the hash of the contents, similar
                     to fw.mgmt.build
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for XRC-SRQ's and XRC-QP's for upper layer driver.

We maintain separate bitmaps for resource management for srq and
xrc-srq, However, the range in FW is one, The xrc-srq's are first
and then the srq's follow. Therefore we maintain a srq-id offset.

v2: perform cleanups if XRC bitmpas allocation fail.
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NYuval Bason <ybason@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First ILT page for TSDM client is allocated for XRC-SRQ's.
For regular SRQ's skip first ILT page that is reserved for
XRC-SRQ's.
Signed-off-by: NMichal Kalderon <mkalderon@marvell.com>
Signed-off-by: NYuval Bason <ybason@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every time we access the 'etype' and 'vlan_tci' fields from struct
igc_nfc_filter to enable or disable filters in hardware we have to
convert them from big endian to host order so it makes more sense to
simply have these fields in host order.

The byte order conversion should take place in igc_ethtool_get_nfc_
rule() and igc_ethtool_add_nfc_rule(), which are called by .get_rxnfc
and .set_rxnfc ethtool ops, since ethtool subsystem is the one who deals
with them in big endian order.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Network Flow Classification (NFC) support code from IGC driver uses
terms such as 'rule', 'filter', 'entry', 'input' interchangeably when
referring to NFC rules, making it harder to follow the code. This patch
renames IGC's internal APIs, structs, and variables so we stick with the
term 'rule' since this is the term used in ethtool APIs. It also removes
some not applicable comments along the way. No functionality is changed
by this patch.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the prefix 'igc_ethtool_' to all functions defined in
igc_ethtool.c so they align with the name convention already followed by
other parts of the driver (e.g. igc_tsn, igc_ptp). Also, this avoids
some name clashing with functions added to igc_main.c by upcoming
patches in this series. No functionality is changed by this patch, just
function renaming.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch re-writes the second half of igc_ethtool_get_nfc_entry() to
follow the 'return early' pattern seen in other parts of the driver and
removes some duplicate comments.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does a trivial change in igc_ethtool_get_rxnfc() and
igc_ethtool_set_rxnfc() to simplify their logic.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The local function igc_max_channels() is a pointless wrapper around
igc_get_max_rss_queues(). This patch removes it and updates the callers
accordingly. It also does some cleanup on igc_get_max_rss_queues().
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The 'cookie' field is not used anywhere in the code so this patch
removes it from struct igc_nfc_filter.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Per queue good transmitted packet counter not applicable for i225 device.
This patch comes to clean up this register.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Header redirection missed packet counter not applicable for i225 device.
This patch comes to clean up this register.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Part of circuit breaker registers is obsolete
and not applicable for i225 device.
This patch comes to clean up these registers.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are seeing a deadlock in e1000 down when NAPI is being disabled. Looking
over the kernel function trace of the system it appears that the interface
is being closed and then a reset is hitting which deadlocks the interface
as the NAPI interface is already disabled.

To prevent this from happening I am disabling the reset task when
__E1000_DOWN is already set. In addition code has been added so that we set
the __E1000_DOWN while holding the __E1000_RESET flag in e1000_close in
order to guarantee that the reset task will not run after we have started
the close call.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: NMaxim Zhukov <mussitantesmortem@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for Network Flow Classification (NFC) rules
based on source MAC address. Note that the controller doesn't support
rules with both source and destination addresses set, so this special
case is checked in igc_add_ethtool_nfc_entry().
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch extends MAC address filter internal APIs igc_add_mac_filter()
and igc_del_mac_filter(), as well as local helpers, to support filters
based on source address.

A new parameters 'type' is added to the APIs to indicate if the filter
type is source or destination. In case it is source type, the RAH
register is configured accordingly in igc_set_mac_filter_hw().
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In igc_adapter we keep a sort of shadow copy of RAL and RAH registers.
There is not much benefit in keeping it, at the cost of maintainability,
since adding/removing MAC address filters is not hot path, and we
already keep filters information in adapter->nfc_filter_list for cleanup
and restoration purposes.

So in order to simplify the MAC address filtering code and prepare it
for source address support, this patch removes the mac_table from
igc_adapter.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>