This change essentially makes it so that we can enable almost all of the
features all at once.  This patch allows for the combination of SR-IOV,
DCB, and FCoE in the case of the x540.  It also beefs up the SR-IOV by
adding support for RSS to the PF.

The testing matrix gets to be very complex for this patch as there are a
number of different features and subsets for queueing options.  I tried to
narrow these down a bit by restricting the PF to only supporting 4TC DCB
when it is enabled in addition to SR-IOV.

Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change allows all pools from the default pool forward to be enabled vi
ixgbe_configure_virtualization.  This is needed as we are planning to use
queues belonging to adjacent pools for FCoE when SR-IOV and FCoE are both
enabled.

In addition this patch contains some minor formatting changes as there were
a few spots that seemed to be in need of some cleanup.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to make the code much more readable for MTQC and MRQC
configuration.

The big change is that I simplified much of the logic so that we are
essentially handling just 4 cases and their variants. In the cases where
RSS is disabled we are actually just programming the RETA table with all
1s resulting in a single queue RSS. In the case of SR-IOV I am treating
that as a subset of VMDq. This all results int he following configuration
for the hardware:
         DCB
         En       Dis
VMDq En  VMDQ/DCB VMDq/RSS
     Dis DCB/RSS  RSS

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up some of the logic in an attempt to try and simplify
things for how we are configuring DCB w/ RSS.

In this patch I basically did 3 things.  I updated the logic for getting
the first register index.  I applied the fact that all TCs get the same
number of queues to simplify the looping logic in caching the DCB ring
register.  Finally I updated how we configure the RQTC register to match
the fact that all TCs are assigned the same number of queues.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It makes much more sense for us to configure the real number of Tx and Rx
queues in the ixgbe_open call than it does in ixgbe_set_num_queues.  By
setting the number in ixgbe_open we can avoid a number of unecessary
updates and only have to make the calls once.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were exiting without cleaning up the memory internally on the
ixgbe_setup_rx_resources and ixgbe_setup_tx_resources calls.  Instead of
forcing the caller to clean things up for us we should instead just unwind
the rings and free the memory as we go.  This way we can more gracefully
clean up the rings in the event of an allocation failure.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the link status changes on the PF we need to notify the VFs. In order
to do this we should ping all of the VFs in order to trigger a link status
change on them as well.

This fixes issues in which the PF would reset, but the VF didn't because the
NAK flag was not set in the VF mailbox.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change merges the ixgbe_cache_ring_fcoe and ixgbe_set_fcoe_queues
logic into the DCB and RSS initialization calls.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In upcoming patches it will become increasingly common to need to determine
the FCoE traffic class in order to determine the correct queues for FCoE.
In order to make this easier I am adding a function for obtaining the FCoE
traffic class based on the user priority.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There were cases where the prio_tc_map was not populated when we were
calling open.  This will result in us incorrectly configuring the traffic
classes when DCB is enabled.  In order to correct this I have updated the
code so that we now populate the values prior to allocating the q_vectors
and calling ixgbe_open.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces a switch statement for an 82598 workaround with an if
statement that only applies to 82598. In addition I am pulling out several
dead pieces of code and instead of reading the SRRCTL register and then
modifying it we are just writing a value which we generate from scratch.
Finally I am also removing any drop enable related code since that was
moved to a function of its own.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The mask value for ring features was overloaded for FCoE which can lead to
some confusion.  In order to avoid any confusion I am splitting the mask
value and adding an offset value.  This can be used for the start of the
FCoE rings, and in the future I hope to use it to store the start of the
registers for SR-IOV.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are currently using indices to indicate the upper limit on a ring
feature.  However since we can switch back and forth on features such as
DCB and that has effects on other features such as RSS it is preferable to
instead store the upper limit separate from the current value for the
number of rings related to the feature.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It makes much more sense for us to count q_vectors instead of MSI-X
vectors.  We were using num_msix_vectors to find the number of q_vectors in
multiple places.  This was wasteful since we only had one place that
actually needs the number of MSI-X vectors and that is in slow path.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.  Delete
a few that are content-free.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DCB and SR-IOV cannot currently be enabled at the same time as the queueing
schemes are incompatible.  If they are both enabled it will result in Tx
hangs since only the first Tx queue will be able to transmit any traffic.

This simple fix for this is to block us from enabling TCs in ixgbe_setup_tc
if SR-IOV is enabled.  This change will be reverted once we can support
SR-IOV and DCB coexistence.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FCoE target mode was experiencing issues due to the fact that we were
sending up data frames that were padded to 60 bytes after the DDP logic had
already stripped the frame down to 52 or 56 depending on the use of VLANs.
This was resulting in the FCoE DDP logic having issues since it thought the
frame still had data in it due to the padding.

To resolve this, adding code so that we do not pad FCoE frames prior to
handling them to the stack.

CC: <stable@vger.kernel.org>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check for length <= 0 is bogus because length is unsigned, and network
stack never sends zero length packets (unless it is totally broken).

The check for really small packets can be optimized (using unlikely)
and calling skb_pad directly.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a memory leak that was introduced in the 3.4 kernel.  The
leak occurred when FCoE was enabled and traffic was passed over the FCoE
rings reserved for FCoE.  The memory leak was due to us not populating the
compound page information on the order 1 pages needed for FCoE.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a potential Rx timestamp deadlock that causes the Rx
timestamping to stall indefinitely. The issue could occur when a PTP packet is
timestamped by hardware but never reaches the Rx queue. In order to prevent a
permanent loss of timestamping, the RXSTMP(L/H) registers have to be read to
unlock them. (This used to only occur when a packet that was timestamped
reached the software.) However the registers can't be read early otherwise
there is no way to correlate them to the packet.

This patch introduces a filter function which can be used to determine if a
packet should have been timestamped. Supplied with the filter setup by the
hwtstamp ioctl, check to make sure the PTP protocol and message type match the
expected values. If so, then read the timestamp registers (to free them.) At
this point check the descriptor bit, if the bit is set then we know this
packet correlates to the timestamp stored in the RXTSTAMP registers.
Otherwise, assume that packet was dropped by the hardware, and ignore this
timestamp value. However, we have at least unlocked the rxtstamp registers for
future timestamping.

Due to the way the driver handles skb data, it cannot be directly accessed. In
order to work around this, a copy of the skb data into a linear buffer is
made. From this buffer it becomes possible to read the data correctly
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes two minor nits from Richard Cochran. The first is a case of
ambitious line wrapping that wasn't necessary. The second is to re-order the
flag checks for PPS support. Previously, the hardware test was done first, and
the interrupt flag test was done second. Now, test the interrupt flag and use
the unlikely macro.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware bit IXGBE_RXD_STAT_VP appears to be set even when Rx
stripping is disabled. This results in passing frames up the stack
which do not have the 802.1Q tag stripped but have the tci bits
set as if it was.

Working around this with a check for the feature flag bit. I
would welcome any better ideas or a pointer to exactly which
bits in the hardware register need to be cleared to get the
IXGBE_RXD_STAT_VP bit to be set per data sheet.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

DCB can be used independent of if RX VLAN stripping is enabled
or disabled so remove erroneous check.

Also enable or disable VLAN stripping when features are applied so
hardware and feature flags are in sync.

CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update version number to better match the version of the out of tree
driver with similar functionality.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the hwmon code was initially added it was with the assumption that a
sysfs patch would be also coming soon.  Since that isn't the case some
clean up needs to be done.  This patch does that.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the MAC, in order to provide the best software
timestamps. This patch adds this call for that support.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables the PPS system in the PHC framework, by enabling
the clock-out feature on the X540 device. Causes the SDP0 to be set as
a 1Hz clock. Also configures the timesync interrupt cause in order to
report each pulse to the PPS via the PHC framework, which can be used
for general system clock synchronization. (This allows a stable method
for tuning the general system time via the on-board SYSTIM register
based clock.)
Signed-off-by: NJacob E Keller <jacob.e.keller@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables hardware timestamping for use with PTP software by
extracting a ns counter from an arbitrary fixed point cycles counter.
The hardware generates SYSTIME registers using the DMA tick which
changes based on the current link speed. These SYSTIME registers are
converted to ns using the cyclecounter and timecounter structures
provided by the kernel. Using the SO_TIMESTAMPING api, software can
enable and access timestamps for PTP packets.

The SO_TIMESTAMPING API has space for 3 different kinds of timestamps,
SYS, RAW, and SOF. SYS hardware timestamps are hardware ns values that
are then scaled to the software clock. RAW hardware timestamps are the
direct raw value of the ns counter. SOF software timestamps are the
software timestamp calculated as close as possible to the software
transmit, but are not offloaded to the hardware. This patch only
supports the RAW hardware timestamps due to inefficiency of the SYS
design.

This patch also enables the PHC subsystem features for atomically
adjusting the cycle register, and adjusting the clock frequency in
parts per billion. This frequency adjustment works by slightly
adjusting the value added to the cycle registers each DMA tick. This
causes the hardware registers to overflow rapidly (approximately once
every 34 seconds, when at 10gig link). To solve this, the timecounter
structure is used, along with a timer set for every 25 seconds. This
allows for detecting register overflow and converting the cycle
counter registers into ns values needed for providing useful
timestamps to the network stack.

Only the basic required clock functions are supported at this time,
although the hardware supports some ancillary features and these could
easily be enabled in the future.

Note that use of this hardware timestamping requires modifying daemon
software to use the SO_TIMESTAMPING API for timestamps, and the
ptp_clock PHC framework for accessing the clock. The timestamps have
no relation to the system time at all, so software must use the posix
clock generated by the PHC framework instead.
Signed-off-by: NJacob E Keller <jacob.e.keller@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The drop enable bit can be used to improve the performance of the adapter
in the case of multiple queues being present.  This performance gain is due
to the fact that some slower CPUs can cause the FIFO to backfill preventing
faster CPUs from receiving additional work.  By setting the drop enable bit
we prevent this and instead just drop the packets that would have been
bound for the slower CPU.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up the logic in the priority based flow control
configuration routines.  Both the 82599 and 82598 based routines perform
similar functions however they are both arranged completely differently.
This patch goes over both of them to clean up the code.

In addition I am dropping the ixgbe_fc_pfc flow control mode and instead
just replacing it with checks for if priority flow control is enabled.
This allows us to maintain some of the link flow control information which
allows for an easier transition between link and priority flow control.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

PFC stats are only tabulated when PFC is enabled. However in IEEE
mode the ieee_pfc pfc_tc bits were not checked and the calculation
was aborted.

This results in statistics not being reported through ethtool and
possible a false Tx hang occurring when receiving pause frames.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

igb and ixgbe incorrectly call netdev_tx_reset_queue() from
i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except
when the number of real tx queues changes. When the number of real
tx queues changes netdev_tx_reset_queue() only gets called on the
new number of queues so when we reduce the number of queues we risk
triggering the watchdog timer and repeated device resets.

So this is not only a cosmetic issue but causes real bugs. For
example enabling/disabling DCB or FCoE in ixgbe will trigger this.

CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NJohn Bishop <johnx.bishop@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change updates the link flow control configuration so that we
correctly set the link flow control settings for DCB.  Previously we would
have to call the fc_enable call 8 times, once for each packet buffer.  If
we move that logic into the fc_enable call itself we can avoid multiple
unnecessary register writes.

This change also corrects an issue in which we were only shifting the water
marks for 82599 parts by 6 instead of 10.  This was resulting in us only
using 1/16 of the packet buffer when flow control was enabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change replaces the calls to put_page with calls to __free_page.

Since the FCoE code is able to access order 1 pages I thought it would be a
good idea to change things over to using __free_pages since that is the
preferred approach for freeing pages.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we can track instances of where a packet was
dropped due to a packet being received when there are no DMA buffers
available in the ring.

For some reason this was only being enabled with RSC, however it makes
more sense to always have this feature on so that we can track any cases
where we might drop a buffer due to an Rx ring being full.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

After this commit:

commit aacc1bea
Author: Multanen, Eric W <eric.w.multanen@intel.com>
Date:   Wed Mar 28 07:49:09 2012 +0000

    ixgbe: driver fix for link flap

The BIT_APP_UPCHG bit is no longer set when ixgbe_dcbnl_set_all() is
called. This results in the FCoE app user priority never getting set
and the driver will not configure the tx_rings correctly for FCoE
packets which use the SAN MTU and FCoE offloads.

We resolve this regression by fixing ixgbe_copy_dcb_cfg() to also
check for FCoE application changes. Additionally, we can drop the
IEEE variants of get_dcb_app() because this path is never called
with the IEEE mode enabled.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It was possible for shutdown to pull the rug out from other driver entry
points.  Now we just grab the rtnl lock before taking everything apart.
Thanks to Hariharan for noticing this tight race condition.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Cc: Hariharan Nagarajan <hanagara@cisco.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the user request for the number of VFs in the max_vfs parameter is
out of range then reset the value to the default value of zero.  This
makes the behavior of the ixgbe driver the same as for the igb driver.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NRobert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of our adapters have thermal data available, this patch exports
this data via hwmon sysfs interface.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was freeing memory in shutdown instead of remove.  As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver.  This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>