1. replace find_e820_area with memblock_find_in_range
2. replace reserve_early with memblock_x86_reserve_range
3. replace free_early with memblock_x86_free_range.
4. NO_BOOTMEM will switch to use memblock too.
5. use _e820, _early wrap in the patch, in following patch, will
   replace them all
6. because memblock_x86_free_range support partial free, we can remove some special care
7. Need to make sure that memblock_find_in_range() is called after memblock_x86_fill()
   so adjust some calling later in setup.c::setup_arch()
   -- corruption_check and mptable_update

-v2: Move reserve_brk() early
    Before fill_memblock_area, to avoid overlap between brk and memblock_find_in_range()
    that could happen We have more then 128 RAM entry in E820 tables, and
    memblock_x86_fill() could use memblock_find_in_range() to find a new place for
    memblock.memory.region array.
    and We don't need to use extend_brk() after fill_memblock_area()
    So move reserve_brk() early before fill_memblock_area().
-v3: Move find_smp_config early
    To make sure memblock_find_in_range not find wrong place, if BIOS doesn't put mptable
    in right place.
-v4: Treat RESERVED_KERN as RAM in memblock.memory. and they are already in
    memblock.reserved already..
    use __NOT_KEEP_MEMBLOCK to make sure memblock related code could be freed later.
-v5: Generic version __memblock_find_in_range() is going from high to low, and for 32bit
    active_region for 32bit does include high pages
    need to replace the limit with memblock.default_alloc_limit, aka get_max_mapped()
-v6: Use current_limit instead
-v7: check with MEMBLOCK_ERROR instead of -1ULL or -1L
-v8: Set memblock_can_resize early to handle EFI with more RAM entries
-v9: update after kmemleak changes in mainline
Suggested-by: NDavid S. Miller <davem@davemloft.net>
Suggested-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Suggested-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

According to node range in early_node_map[] with __memblock_find_in_range
to find free range.

Will be used by memblock_x86_find_in_range_node()

memblock_x86_find_in_range_node will be used to find right buffer for NODE_DATA
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Borislav Petkov reported his 32bit numa system has problem:

[    0.000000] Reserving total of 4c00 pages for numa KVA remap
[    0.000000] kva_start_pfn ~ 32800 max_low_pfn ~ 375fe
[    0.000000] max_pfn = 238000
[    0.000000] 8202MB HIGHMEM available.
[    0.000000] 885MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 375fe000
[    0.000000]   low ram: 0 - 375fe000
[    0.000000] alloc (nid=8 100000 - 7ee00000) (1000000 - ffffffff) 1000 1000 => 34e7000
[    0.000000] alloc (nid=8 100000 - 7ee00000) (1000000 - ffffffff) 200 40 => 34c9d80
[    0.000000] alloc (nid=0 100000 - 7ee00000) (1000000 - ffffffffffffffff) 180 40 => 34e6140
[    0.000000] alloc (nid=1 80000000 - c7e60000) (1000000 - ffffffffffffffff) 240 40 => 80000000
[    0.000000] BUG: unable to handle kernel paging request at 40000000
[    0.000000] IP: [<c2c8cff1>] __alloc_memory_core_early+0x147/0x1d6
[    0.000000] *pdpt = 0000000000000000 *pde = f000ff53f000ff00
...
[    0.000000] Call Trace:
[    0.000000]  [<c2c8b4f8>] ? __alloc_bootmem_node+0x216/0x22f
[    0.000000]  [<c2c90c9b>] ? sparse_early_usemaps_alloc_node+0x5a/0x10b
[    0.000000]  [<c2c9149e>] ? sparse_init+0x1dc/0x499
[    0.000000]  [<c2c79118>] ? paging_init+0x168/0x1df
[    0.000000]  [<c2c780ff>] ? native_pagetable_setup_start+0xef/0x1bb

looks like it allocates too much high address for bootmem.

Try to cut limit with get_max_mapped()
Reported-by: NBorislav Petkov <borislav.petkov@amd.com>
Tested-by: NConny Seidel <conny.seidel@amd.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>		[2.6.34.x]
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With commits 08677214 and 59be5a8e, alloc_bootmem()/free_bootmem() and
friends use the early_res functions for memory management when
NO_BOOTMEM is enabled. This patch adds the kmemleak calls in the
corresponding code paths for bootmem allocations.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>
Acked-by: NYinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org

Introduce numa_mem_id(), based on generic percpu variable infrastructure
to track "nearest node with memory" for archs that support memoryless
nodes.

Define API in <linux/topology.h> when CONFIG_HAVE_MEMORYLESS_NODES
defined, else stubs.  Architectures will define HAVE_MEMORYLESS_NODES
if/when they support them.

Archs can override definitions of:

numa_mem_id() - returns node number of "local memory" node
set_numa_mem() - initialize [this cpus'] per cpu variable 'numa_mem'
cpu_to_mem()  - return numa_mem for specified cpu; may be used as lvalue

Generic initialization of 'numa_mem' occurs in __build_all_zonelists().
This will initialize the boot cpu at boot time, and all cpus on change of
numa_zonelist_order, or when node or memory hot-plug requires zonelist
rebuild.  Archs that support memoryless nodes will need to initialize
'numa_mem' for secondary cpus as they're brought on-line.

[akpm@linux-foundation.org: fix build]
Signed-off-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rework the generic version of the numa_node_id() function to use the new
generic percpu variable infrastructure.

Guard the new implementation with a new config option:

        CONFIG_USE_PERCPU_NUMA_NODE_ID.

Archs which support this new implemention will default this option to 'y'
when NUMA is configured.  This config option could be removed if/when all
archs switch over to the generic percpu implementation of numa_node_id().
Arch support involves:

  1) converting any existing per cpu variable implementations to use
     this implementation.  x86_64 is an instance of such an arch.
  2) archs that don't use a per cpu variable for numa_node_id() will
     need to initialize the new per cpu variable "numa_node" as cpus
     are brought on-line.  ia64 is an example.
  3) Defining USE_PERCPU_NUMA_NODE_ID in arch dependent Kconfig--e.g.,
     when NUMA is configured.  This is required because I have
     retained the old implementation by default to allow archs to
     be modified incrementally, as desired.

Subsequent patches will convert x86_64 and ia64 to use this implemenation.
Signed-off-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Eric Whitney <eric.whitney@hp.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add global mutex zonelists_mutex to fix the possible race:

     CPU0                                  CPU1                    CPU2
(1) zone->present_pages += online_pages;
(2)                                       build_all_zonelists();
(3)                                                               alloc_page();
(4)                                                               free_page();
(5) build_all_zonelists();
(6)   __build_all_zonelists();
(7)     zone->pageset = alloc_percpu();

In step (3,4), zone->pageset still points to boot_pageset, so bad
things may happen if 2+ nodes are in this state. Even if only 1 node
is accessing the boot_pageset, (3) may still consume too much memory
to fail the memory allocations in step (7).

Besides, atomic operation ensures alloc_percpu() in step (7) will never fail
since there is a new fresh memory block added in step(6).

[haicheng.li@linux.intel.com: hold zonelists_mutex when build_all_zonelists]
Signed-off-by: NHaicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Reviewed-by: NAndi Kleen <andi.kleen@intel.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For each new populated zone of hotadded node, need to update its pagesets
with dynamically allocated per_cpu_pageset struct for all possible CPUs:

    1) Detach zone->pageset from the shared boot_pageset
       at end of __build_all_zonelists().

    2) Use mutex to protect zone->pageset when it's still
       shared in onlined_pages()

Otherwises, multiple zones of different nodes would share same boot strapping
boot_pageset for same CPU, which will finally cause below kernel panic:

  ------------[ cut here ]------------
  kernel BUG at mm/page_alloc.c:1239!
  invalid opcode: 0000 [#1] SMP
  ...
  Call Trace:
   [<ffffffff811300c1>] __alloc_pages_nodemask+0x131/0x7b0
   [<ffffffff81162e67>] alloc_pages_current+0x87/0xd0
   [<ffffffff81128407>] __page_cache_alloc+0x67/0x70
   [<ffffffff811325f0>] __do_page_cache_readahead+0x120/0x260
   [<ffffffff81132751>] ra_submit+0x21/0x30
   [<ffffffff811329c6>] ondemand_readahead+0x166/0x2c0
   [<ffffffff81132ba0>] page_cache_async_readahead+0x80/0xa0
   [<ffffffff8112a0e4>] generic_file_aio_read+0x364/0x670
   [<ffffffff81266cfa>] nfs_file_read+0xca/0x130
   [<ffffffff8117b20a>] do_sync_read+0xfa/0x140
   [<ffffffff8117bf75>] vfs_read+0xb5/0x1a0
   [<ffffffff8117c151>] sys_read+0x51/0x80
   [<ffffffff8103c032>] system_call_fastpath+0x16/0x1b
  RIP  [<ffffffff8112ff13>] get_page_from_freelist+0x883/0x900
   RSP <ffff88000d1e78a8>
  ---[ end trace 4bda28328b9990db ]

[akpm@linux-foundation.org: merge fix]
Signed-off-by: NHaicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Reviewed-by: NAndi Kleen <andi.kleen@intel.com>
Reviewed-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No behavior change here.

Move some of setup_per_cpu_pageset() code into a new function
setup_zone_pageset() that will be useful for memory hotplug.
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NHaicheng Li <haicheng.li@linux.intel.com>
Reviewed-by: NAndi Kleen <andi.kleen@intel.com>
Reviewed-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

free_hot_cold_page() and __free_pages_ok() have very similar freeing
preparation.  Consolidate them.

[akpm@linux-foundation.org: fix busted coding style]
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: NMel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The fragmentation index may indicate that a failure is due to external
fragmentation but after a compaction run completes, it is still possible
for an allocation to fail.  There are two obvious reasons as to why

  o Page migration cannot move all pages so fragmentation remains
  o A suitable page may exist but watermarks are not met

In the event of compaction followed by an allocation failure, this patch
defers further compaction in the zone (1 << compact_defer_shift) times.
If the next compaction attempt also fails, compact_defer_shift is
increased up to a maximum of 6.  If compaction succeeds, the defer
counters are reset again.

The zone that is deferred is the first zone in the zonelist - i.e.  the
preferred zone.  To defer compaction in the other zones, the information
would need to be stored in the zonelist or implemented similar to the
zonelist_cache.  This would impact the fast-paths and is not justified at
this time.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ordinarily when a high-order allocation fails, direct reclaim is entered
to free pages to satisfy the allocation.  With this patch, it is
determined if an allocation failed due to external fragmentation instead
of low memory and if so, the calling process will compact until a suitable
page is freed.  Compaction by moving pages in memory is considerably
cheaper than paging out to disk and works where there are locked pages or
no swap.  If compaction fails to free a page of a suitable size, then
reclaim will still occur.

Direct compaction returns as soon as possible.  As each block is
compacted, it is checked if a suitable page has been freed and if so, it
returns.

[akpm@linux-foundation.org: Fix build errors]
[aarcange@redhat.com: fix count_vm_event preempt in memory compaction direct reclaim]
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Acked-by: NRik van Riel <riel@redhat.com>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch is the core of a mechanism which compacts memory in a zone by
relocating movable pages towards the end of the zone.

A single compaction run involves a migration scanner and a free scanner.
Both scanners operate on pageblock-sized areas in the zone.  The migration
scanner starts at the bottom of the zone and searches for all movable
pages within each area, isolating them onto a private list called
migratelist.  The free scanner starts at the top of the zone and searches
for suitable areas and consumes the free pages within making them
available for the migration scanner.  The pages isolated for migration are
then migrated to the newly isolated free pages.

[aarcange@redhat.com: Fix unsafe optimisation]
[mel@csn.ul.ie: do not schedule work on other CPUs for compaction]
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Acked-by: NRik van Riel <riel@redhat.com>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are two types of zonelist ordering methodologies:

 - node order, preferring allocations on a node to stay local to and

 - zone order, preferring allocations come from a higher zone to avoid
   allocating in lowmem zones even though they may not be local.

The ordering technique used by the kernel is configurable on the command
line, but also has some logic to determine what the default should be.

This logic currently lacks knowledge of systems where a node may only have
lowmem.  For such systems, it is necessary to use node order so that
GFP_KERNEL allocations may be satisfied by nodes consisting of only
lowmem.

If zone order is used, GFP_KERNEL allocations to such nodes are actually
allocated on a node with local affinity that includes ZONE_NORMAL.

This change defaults to node zonelist ordering if any node lacks
ZONE_NORMAL.

To force zone order, append 'numa_zonelist_order=zone' to the kernel
command line.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Acked-by: NMel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Before applying this patch, cpuset updates task->mems_allowed and
mempolicy by setting all new bits in the nodemask first, and clearing all
old unallowed bits later.  But in the way, the allocator may find that
there is no node to alloc memory.

The reason is that cpuset rebinds the task's mempolicy, it cleans the
nodes which the allocater can alloc pages on, for example:

(mpol: mempolicy)
	task1			task1's mpol	task2
	alloc page		1
	  alloc on node0? NO	1
				1		change mems from 1 to 0
				1		rebind task1's mpol
				0-1		  set new bits
				0	  	  clear disallowed bits
	  alloc on node1? NO	0
	  ...
	can't alloc page
	  goto oom

This patch fixes this problem by expanding the nodes range first(set newly
allowed bits) and shrink it lazily(clear newly disallowed bits).  So we
use a variable to tell the write-side task that read-side task is reading
nodemask, and the write-side task clears newly disallowed nodes after
read-side task ends the current memory allocation.

[akpm@linux-foundation.org: fix spello]
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Paul Menage <menage@google.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

page allocator: reduce fragmentation in buddy allocator by adding buddies that are merging to the tail of the free lists

In order to reduce fragmentation, this patch classifies freed pages in two
groups according to their probability of being part of a high order merge.
 Pages belonging to a compound whose next-highest buddy is free are more
likely to be part of a high order merge in the near future, so they will
be added at the tail of the freelist.  The remaining pages are put at the
front of the freelist.

In this way, the pages that are more likely to cause a big merge are kept
free longer.  Consequently there is a tendency to aggregate the
long-living allocations on a subset of the compounds, reducing the
fragmentation.

This heuristic was tested on three machines, x86, x86-64 and ppc64 with
3GB of RAM in each machine.  The tests were kernbench, netperf, sysbench
and STREAM for performance and a high-order stress test for huge page
allocations.

KernBench X86
Elapsed mean     374.77 ( 0.00%)   375.10 (-0.09%)
User    mean     649.53 ( 0.00%)   650.44 (-0.14%)
System  mean      54.75 ( 0.00%)    54.18 ( 1.05%)
CPU     mean     187.75 ( 0.00%)   187.25 ( 0.27%)

KernBench X86-64
Elapsed mean      94.45 ( 0.00%)    94.01 ( 0.47%)
User    mean     323.27 ( 0.00%)   322.66 ( 0.19%)
System  mean      36.71 ( 0.00%)    36.50 ( 0.57%)
CPU     mean     380.75 ( 0.00%)   381.75 (-0.26%)

KernBench PPC64
Elapsed mean     173.45 ( 0.00%)   173.74 (-0.17%)
User    mean     587.99 ( 0.00%)   587.95 ( 0.01%)
System  mean      60.60 ( 0.00%)    60.57 ( 0.05%)
CPU     mean     373.50 ( 0.00%)   372.75 ( 0.20%)

Nothing notable for kernbench.

NetPerf UDP X86
      64    42.68 ( 0.00%)     42.77 ( 0.21%)
     128    85.62 ( 0.00%)     85.32 (-0.35%)
     256   170.01 ( 0.00%)    168.76 (-0.74%)
    1024   655.68 ( 0.00%)    652.33 (-0.51%)
    2048  1262.39 ( 0.00%)   1248.61 (-1.10%)
    3312  1958.41 ( 0.00%)   1944.61 (-0.71%)
    4096  2345.63 ( 0.00%)   2318.83 (-1.16%)
    8192  4132.90 ( 0.00%)   4089.50 (-1.06%)
   16384  6770.88 ( 0.00%)   6642.05 (-1.94%)*

NetPerf UDP X86-64
      64   148.82 ( 0.00%)    154.92 ( 3.94%)
     128   298.96 ( 0.00%)    312.95 ( 4.47%)
     256   583.67 ( 0.00%)    626.39 ( 6.82%)
    1024  2293.18 ( 0.00%)   2371.10 ( 3.29%)
    2048  4274.16 ( 0.00%)   4396.83 ( 2.79%)
    3312  6356.94 ( 0.00%)   6571.35 ( 3.26%)
    4096  7422.68 ( 0.00%)   7635.42 ( 2.79%)*
    8192 12114.81 ( 0.00%)* 12346.88 ( 1.88%)
   16384 17022.28 ( 0.00%)* 17033.19 ( 0.06%)*
             1.64%             2.73%

NetPerf UDP PPC64
      64    49.98 ( 0.00%)     50.25 ( 0.54%)
     128    98.66 ( 0.00%)    100.95 ( 2.27%)
     256   197.33 ( 0.00%)    191.03 (-3.30%)
    1024   761.98 ( 0.00%)    785.07 ( 2.94%)
    2048  1493.50 ( 0.00%)   1510.85 ( 1.15%)
    3312  2303.95 ( 0.00%)   2271.72 (-1.42%)
    4096  2774.56 ( 0.00%)   2773.06 (-0.05%)
    8192  4918.31 ( 0.00%)   4793.59 (-2.60%)
   16384  7497.98 ( 0.00%)   7749.52 ( 3.25%)

The tests are run to have confidence limits within 1%.  Results marked
with a * were not confident although in this case, it's only outside by
small amounts.  Even with some results that were not confident, the
netperf UDP results were generally positive.

NetPerf TCP X86
      64   652.25 ( 0.00%)*   648.12 (-0.64%)*
            23.80%            22.82%
     128  1229.98 ( 0.00%)*  1220.56 (-0.77%)*
            21.03%            18.90%
     256  2105.88 ( 0.00%)   1872.03 (-12.49%)*
             1.00%            16.46%
    1024  3476.46 ( 0.00%)*  3548.28 ( 2.02%)*
            13.37%            11.39%
    2048  4023.44 ( 0.00%)*  4231.45 ( 4.92%)*
             9.76%            12.48%
    3312  4348.88 ( 0.00%)*  4396.96 ( 1.09%)*
             6.49%             8.75%
    4096  4726.56 ( 0.00%)*  4877.71 ( 3.10%)*
             9.85%             8.50%
    8192  4732.28 ( 0.00%)*  5777.77 (18.10%)*
             9.13%            13.04%
   16384  5543.05 ( 0.00%)*  5906.24 ( 6.15%)*
             7.73%             8.68%

NETPERF TCP X86-64
            netperf-tcp-vanilla-netperf       netperf-tcp
                   tcp-vanilla     pgalloc-delay
      64  1895.87 ( 0.00%)*  1775.07 (-6.81%)*
             5.79%             4.78%
     128  3571.03 ( 0.00%)*  3342.20 (-6.85%)*
             3.68%             6.06%
     256  5097.21 ( 0.00%)*  4859.43 (-4.89%)*
             3.02%             2.10%
    1024  8919.10 ( 0.00%)*  8892.49 (-0.30%)*
             5.89%             6.55%
    2048 10255.46 ( 0.00%)* 10449.39 ( 1.86%)*
             7.08%             7.44%
    3312 10839.90 ( 0.00%)* 10740.15 (-0.93%)*
             6.87%             7.33%
    4096 10814.84 ( 0.00%)* 10766.97 (-0.44%)*
             6.86%             8.18%
    8192 11606.89 ( 0.00%)* 11189.28 (-3.73%)*
             7.49%             5.55%
   16384 12554.88 ( 0.00%)* 12361.22 (-1.57%)*
             7.36%             6.49%

NETPERF TCP PPC64
            netperf-tcp-vanilla-netperf       netperf-tcp
                   tcp-vanilla     pgalloc-delay
      64   594.17 ( 0.00%)    596.04 ( 0.31%)*
             1.00%             2.29%
     128  1064.87 ( 0.00%)*  1074.77 ( 0.92%)*
             1.30%             1.40%
     256  1852.46 ( 0.00%)*  1856.95 ( 0.24%)
             1.25%             1.00%
    1024  3839.46 ( 0.00%)*  3813.05 (-0.69%)
             1.02%             1.00%
    2048  4885.04 ( 0.00%)*  4881.97 (-0.06%)*
             1.15%             1.04%
    3312  5506.90 ( 0.00%)   5459.72 (-0.86%)
    4096  6449.19 ( 0.00%)   6345.46 (-1.63%)
    8192  7501.17 ( 0.00%)   7508.79 ( 0.10%)
   16384  9618.65 ( 0.00%)   9490.10 (-1.35%)

There was a distinct lack of confidence in the X86* figures so I included
what the devation was where the results were not confident.  Many of the
results, whether gains or losses were within the standard deviation so no
solid conclusion can be reached on performance impact.  Looking at the
figures, only the X86-64 ones look suspicious with a few losses that were
outside the noise.  However, the results were so unstable that without
knowing why they vary so much, a solid conclusion cannot be reached.

SYSBENCH X86
              sysbench-vanilla     pgalloc-delay
           1  7722.85 ( 0.00%)  7756.79 ( 0.44%)
           2 14901.11 ( 0.00%) 13683.44 (-8.90%)
           3 15171.71 ( 0.00%) 14888.25 (-1.90%)
           4 14966.98 ( 0.00%) 15029.67 ( 0.42%)
           5 14370.47 ( 0.00%) 14865.00 ( 3.33%)
           6 14870.33 ( 0.00%) 14845.57 (-0.17%)
           7 14429.45 ( 0.00%) 14520.85 ( 0.63%)
           8 14354.35 ( 0.00%) 14362.31 ( 0.06%)

SYSBENCH X86-64
           1 17448.70 ( 0.00%) 17484.41 ( 0.20%)
           2 34276.39 ( 0.00%) 34251.00 (-0.07%)
           3 50805.25 ( 0.00%) 50854.80 ( 0.10%)
           4 66667.10 ( 0.00%) 66174.69 (-0.74%)
           5 66003.91 ( 0.00%) 65685.25 (-0.49%)
           6 64981.90 ( 0.00%) 65125.60 ( 0.22%)
           7 64933.16 ( 0.00%) 64379.23 (-0.86%)
           8 63353.30 ( 0.00%) 63281.22 (-0.11%)
           9 63511.84 ( 0.00%) 63570.37 ( 0.09%)
          10 62708.27 ( 0.00%) 63166.25 ( 0.73%)
          11 62092.81 ( 0.00%) 61787.75 (-0.49%)
          12 61330.11 ( 0.00%) 61036.34 (-0.48%)
          13 61438.37 ( 0.00%) 61994.47 ( 0.90%)
          14 62304.48 ( 0.00%) 62064.90 (-0.39%)
          15 63296.48 ( 0.00%) 62875.16 (-0.67%)
          16 63951.76 ( 0.00%) 63769.09 (-0.29%)

SYSBENCH PPC64
                             -sysbench-pgalloc-delay-sysbench
              sysbench-vanilla     pgalloc-delay
           1  7645.08 ( 0.00%)  7467.43 (-2.38%)
           2 14856.67 ( 0.00%) 14558.73 (-2.05%)
           3 21952.31 ( 0.00%) 21683.64 (-1.24%)
           4 27946.09 ( 0.00%) 28623.29 ( 2.37%)
           5 28045.11 ( 0.00%) 28143.69 ( 0.35%)
           6 27477.10 ( 0.00%) 27337.45 (-0.51%)
           7 26489.17 ( 0.00%) 26590.06 ( 0.38%)
           8 26642.91 ( 0.00%) 25274.33 (-5.41%)
           9 25137.27 ( 0.00%) 24810.06 (-1.32%)
          10 24451.99 ( 0.00%) 24275.85 (-0.73%)
          11 23262.20 ( 0.00%) 23674.88 ( 1.74%)
          12 24234.81 ( 0.00%) 23640.89 (-2.51%)
          13 24577.75 ( 0.00%) 24433.50 (-0.59%)
          14 25640.19 ( 0.00%) 25116.52 (-2.08%)
          15 26188.84 ( 0.00%) 26181.36 (-0.03%)
          16 26782.37 ( 0.00%) 26255.99 (-2.00%)

Again, there is little to conclude here.  While there are a few losses,
the results vary by +/- 8% in some cases.  They are the results of most
concern as there are some large losses but it's also within the variance
typically seen between kernel releases.

The STREAM results varied so little and are so verbose that I didn't
include them here.

The final test stressed how many huge pages can be allocated.  The
absolute number of huge pages allocated are the same with or without the
page.  However, the "unusability free space index" which is a measure of
external fragmentation was slightly lower (lower is better) throughout the
lifetime of the system.  I also measured the latency of how long it took
to successfully allocate a huge page.  The latency was slightly lower and
on X86 and PPC64, more huge pages were allocated almost immediately from
the free lists.  The improvement is slight but there.

[mel@csn.ul.ie: Tested, reworked for less branches]
[czoccolo@gmail.com: fix oops by checking pfn_valid_within()]
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Acked-by: NRik van Riel <riel@redhat.com>
Reviewed-by: NPekka Enberg <penberg@cs.helsinki.fi>
Cc: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[Ss]ytem => [Ss]ystem
udpate => update
paramters => parameters
orginal => original
Signed-off-by: NThomas Weber <swirl@gmx.li>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

- introduce dump_page() to print the page info for debugging some error
  condition.

- convert three mm users: bad_page(), print_bad_pte() and memory offline
  failure.

- print an extra field: the symbolic names of page->flags

Example dump_page() output:

[  157.521694] page:ffffea0000a7cba8 count:2 mapcount:1 mapping:ffff88001c901791 index:0x147
[  157.525570] page flags: 0x100000000100068(uptodate|lru|active|swapbacked)
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Alex Chiang <achiang@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Mel Gorman <mel@linux.vnet.ibm.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__zone_pcp_update() iterates over NR_CPUS instead of limiting the access
to the possible cpus.  This might result in access to uninitialized areas
as the per cpu allocator only populates the per cpu memory for possible
cpus.

This problem was created as a result of the dynamic allocation of pagesets
from percpu memory that went in during the merge window - commit
99dcc3e5 ("this_cpu: Page allocator
conversion").
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>
Acked-by: NTejun Heo <tj@kernel.org>
Acked-by: NChristoph Lameter <cl@linux-foundation.org>
Acked-by: NMel Gorman <mel@csn.ul.ie>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

free_area_init_nodes() emits pfn ranges for all zones on the system.
There may be no pages on a higher zone, however, due to memory limitations
or the use of the mem= kernel parameter.  For example:

Zone PFN ranges:
  DMA      0x00000001 -> 0x00001000
  DMA32    0x00001000 -> 0x00100000
  Normal   0x00100000 -> 0x00100000

The implementation copies the previous zone's highest pfn, if any, as the
next zone's lowest pfn.  If its highest pfn is then greater than the
amount of addressable memory, the upper memory limit is used instead.
Thus, both the lowest and highest possible pfn for higher zones without
memory may be the same.

The pfn range for zones without memory is now shown as "empty" instead.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: NChristoph Lameter <cl@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are quite a few GFP_KERNEL memory allocations made during
suspend/hibernation and resume that may cause the system to hang, because
the I/O operations they depend on cannot be completed due to the
underlying devices being suspended.

Avoid this problem by clearing the __GFP_IO and __GFP_FS bits in
gfp_allowed_mask before suspend/hibernation and restoring the original
values of these bits in gfp_allowed_mask durig the subsequent resume.

[akpm@linux-foundation.org: fix CONFIG_PM=n linkage]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reported-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit e815af95 ("change all_unreclaimable zone member to flags") changed
all_unreclaimable member to bit flag.  But it had an undesireble side
effect.  free_one_page() is one of most hot path in linux kernel and
increasing atomic ops in it can reduce kernel performance a bit.

Thus, this patch revert such commit partially. at least
all_unreclaimable shouldn't share memory word with other zone flags.

[akpm@linux-foundation.org: fix patch interaction]
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Huang Shijie <shijie8@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

free_hot_page() is just a wrapper around free_hot_cold_page() with
parameter 'cold = 0'.  After adding a clear comment for
free_hot_cold_page(), it is reasonable to remove a level of call.

[akpm@linux-foundation.org: fix build]
Signed-off-by: NLi Hong <lihong.hi@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Li Ming Chun <macli@brc.ubc.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move a call of trace_mm_page_free_direct() from free_hot_page() to
free_hot_cold_page().  It is clearer and close to kmemcheck_free_shadow(),
as it is done in function __free_pages_ok().
Signed-off-by: NLi Hong <lihong.hi@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Li Ming Chun <macli@brc.ubc.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

trace_mm_page_free_direct() is called in function __free_pages().  But it
is called again in free_hot_page() if order == 0 and produce duplicate
records in trace file for mm_page_free_direct event.  As below:

K-PID    CPU#    TIMESTAMP  FUNCTION
  gnome-terminal-1567  [000]  4415.246466: mm_page_free_direct: page=ffffea0003db9f40 pfn=1155800 order=0
  gnome-terminal-1567  [000]  4415.246468: mm_page_free_direct: page=ffffea0003db9f40 pfn=1155800 order=0
  gnome-terminal-1567  [000]  4415.246506: mm_page_alloc: page=ffffea0003db9f40 pfn=1155800 order=0 migratetype=0 gfp_flags=GFP_KERNEL
  gnome-terminal-1567  [000]  4415.255557: mm_page_free_direct: page=ffffea0003db9f40 pfn=1155800 order=0
  gnome-terminal-1567  [000]  4415.255557: mm_page_free_direct: page=ffffea0003db9f40 pfn=1155800 order=0

This patch removes the first call and adds a call to
trace_mm_page_free_direct() in __free_pages_ok().
Signed-off-by: NLi Hong <lihong.hi@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Li Ming Chun <macli@brc.ubc.ca>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These build errors on some non-x86 platforms (PowerPC for example):

 mm/page_alloc.c: In function '__alloc_memory_core_early':
   mm/page_alloc.c:3468: error: implicit declaration of function 'find_early_area'
   mm/page_alloc.c:3483: error: implicit declaration of function 'reserve_early_without_check'

The function is only needed on CONFIG_NO_BOOTMEM.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Weiner <hannes@saeurebad.de>
Cc: Mel Gorman <mel@csn.ul.ie>
LKML-Reference: <4B747239.4070907@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Finally we can use early_res to replace bootmem for x86_64 now.

Still can use CONFIG_NO_BOOTMEM to enable it or not.

-v2: fix 32bit compiling about MAX_DMA32_PFN
-v3: folded bug fix from LKML message below
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B747239.4070907@kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

After memory pressure has forced it to dip into the reserves, 2.6.32's
5f8dcc21 "page-allocator: split per-cpu
list into one-list-per-migrate-type" has been returning MIGRATE_RESERVE
pages to the MIGRATE_MOVABLE free_list: in some sense depleting reserves.

Fix that in the most straightforward way (which, considering the overheads
of alternative approaches, is Mel's preference): the right migratetype is
already in page_private(page), but free_pcppages_bulk() wasn't using it.

How did this bug show up?  As a 20% slowdown in my tmpfs loop kbuild
swapping tests, on PowerMac G5 with SLUB allocator.  Bisecting to that
commit was easy, but explaining the magnitude of the slowdown not easy.

The same effect appears, but much less markedly, with SLAB, and even
less markedly on other machines (the PowerMac divides into fewer zones
than x86, I think that may be a factor).  We guess that lumpy reclaim
of short-lived high-order pages is implicated in some way, and probably
this bug has been tickling a poor decision somewhere in page reclaim.

But instrumentation hasn't told me much, I've run out of time and
imagination to determine exactly what's going on, and shouldn't hold up
the fix any longer: it's valid, and might even fix other misbehaviours.
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: NMel Gorman <mel@csn.ul.ie>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit f2260e6b (page allocator: update NR_FREE_PAGES only as necessary)
made one minor regression.  if __rmqueue() was failed, NR_FREE_PAGES stat
go wrong.  this patch fixes it.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Reported-by: NHuang Shijie <shijie8@gmail.com>
Reviewed-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current check for 'backward merging' within add_active_range() does
not seem correct.  start_pfn must be compared against
early_node_map[i].start_pfn (and NOT against .end_pfn) to find out whether
the new region is backward-mergeable with the existing range.
Signed-off-by: NKazuhisa Ichikawa <ki@epsilou.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the per cpu allocator functionality to avoid per cpu arrays in struct zone.

This drastically reduces the size of struct zone for systems with large
amounts of processors and allows placement of critical variables of struct
zone in one cacheline even on very large systems.

Another effect is that the pagesets of one processor are placed near one
another. If multiple pagesets from different zones fit into one cacheline
then additional cacheline fetches can be avoided on the hot paths when
allocating memory from multiple zones.

Bootstrap becomes simpler if we use the same scheme for UP, SMP, NUMA. #ifdefs
are reduced and we can drop the zone_pcp macro.

Hotplug handling is also simplified since cpu alloc can bring up and
shut down cpu areas for a specific cpu as a whole. So there is no need to
allocate or free individual pagesets.

V7-V8:
- Explain chicken egg dilemmna with percpu allocator.

V4-V5:
- Fix up cases where per_cpu_ptr is called before irq disable
- Integrate the bootstrap logic that was separate before.

tj: Build failure in pageset_cpuup_callback() due to missing ret
    variable fixed.
Reviewed-by: NMel Gorman <mel@csn.ul.ie>
Signed-off-by: NChristoph Lameter <cl@linux-foundation.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

The zone list code clearly cannot tolerate concurrent writers (I couldn't
find any locks for that), so simply add a global mutex. No need for RCU
in this case.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Memory balloon drivers can allocate a large amount of memory which is not
movable but could be freed to accomodate memory hotplug remove.

Prior to calling the memory hotplug notifier chain the memory in the
pageblock is isolated.  Currently, if the migrate type is not
MIGRATE_MOVABLE the isolation will not proceed, causing the memory removal
for that page range to fail.

Rather than failing pageblock isolation if the migrateteype is not
MIGRATE_MOVABLE, this patch checks if all of the pages in the pageblock,
and not on the LRU, are owned by a registered balloon driver (or other
entity) using a notifier chain.  If all of the non-movable pages are owned
by a balloon, they can be freed later through the memory notifier chain
and the range can still be isolated in set_migratetype_isolate().
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Brian King <brking@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Gerald Schaefer <geralds@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Found one system that boot from socket1 instead of socket0, SRAT get rejected...

[    0.000000] SRAT: Node 1 PXM 0 0-a0000
[    0.000000] SRAT: Node 1 PXM 0 100000-80000000
[    0.000000] SRAT: Node 1 PXM 0 100000000-2080000000
[    0.000000] SRAT: Node 0 PXM 1 2080000000-4080000000
[    0.000000] SRAT: Node 2 PXM 2 4080000000-6080000000
[    0.000000] SRAT: Node 3 PXM 3 6080000000-8080000000
[    0.000000] SRAT: Node 4 PXM 4 8080000000-a080000000
[    0.000000] SRAT: Node 5 PXM 5 a080000000-c080000000
[    0.000000] SRAT: Node 6 PXM 6 c080000000-e080000000
[    0.000000] SRAT: Node 7 PXM 7 e080000000-10080000000
...
[    0.000000] NUMA: Allocated memnodemap from 500000 - 701040
[    0.000000] NUMA: Using 20 for the hash shift.
[    0.000000] Adding active range (0, 0x2080000, 0x4080000) 0 entries of 3200 used
[    0.000000] Adding active range (1, 0x0, 0x96) 1 entries of 3200 used
[    0.000000] Adding active range (1, 0x100, 0x7f750) 2 entries of 3200 used
[    0.000000] Adding active range (1, 0x100000, 0x2080000) 3 entries of 3200 used
[    0.000000] Adding active range (2, 0x4080000, 0x6080000) 4 entries of 3200 used
[    0.000000] Adding active range (3, 0x6080000, 0x8080000) 5 entries of 3200 used
[    0.000000] Adding active range (4, 0x8080000, 0xa080000) 6 entries of 3200 used
[    0.000000] Adding active range (5, 0xa080000, 0xc080000) 7 entries of 3200 used
[    0.000000] Adding active range (6, 0xc080000, 0xe080000) 8 entries of 3200 used
[    0.000000] Adding active range (7, 0xe080000, 0x10080000) 9 entries of 3200 used
[    0.000000] SRAT: PXMs only cover 917504MB of your 1048566MB e820 RAM. Not used.
[    0.000000] SRAT: SRAT not used.

the early_node_map is not sorted because node0 with non zero start come first.

so try to sort it right away after all regions are registered.

also fixs refression by 8716273c (x86: Export srat physical topology)

-v2: make it more solid to handle cross node case like node0 [0,4g), [8,12g) and node1 [4g, 8g), [12g, 16g)
-v3: update comments.
Reported-and-tested-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B2579D2.3010201@kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Fix node-oriented allocation handling in oom-kill.c I myself think of this
as a bugfix not as an ehnancement.

In these days, things are changed as
  - alloc_pages() eats nodemask as its arguments, __alloc_pages_nodemask().
  - mempolicy don't maintain its own private zonelists.
  (And cpuset doesn't use nodemask for __alloc_pages_nodemask())

So, current oom-killer's check function is wrong.

This patch does
  - check nodemask, if nodemask && nodemask doesn't cover all
    node_states[N_HIGH_MEMORY], this is CONSTRAINT_MEMORY_POLICY.
  - Scan all zonelist under nodemask, if it hits cpuset's wall
    this faiulre is from cpuset.
And
  - modifies the caller of out_of_memory not to call oom if __GFP_THISNODE.
    This doesn't change "current" behavior. If callers use __GFP_THISNODE
    it should handle "page allocation failure" by itself.

  - handle __GFP_NOFAIL+__GFP_THISNODE path.
    This is something like a FIXME but this gfpmask is not used now.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hioryu@jp.fujitsu.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Most free pages in the buddy system have no PG_buddy set.
Introduce is_free_buddy_page() for detecting them reliably.

CC: Nick Piggin <npiggin@suse.de>
CC: Mel Gorman <mel@linux.vnet.ibm.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Remove three degrees of obfuscation, left over from when we had
CONFIG_UNEVICTABLE_LRU.  MLOCK_PAGES is CONFIG_HAVE_MLOCKED_PAGE_BIT is
CONFIG_HAVE_MLOCK is CONFIG_MMU.  rmap.o (and memory-failure.o) are only
built when CONFIG_MMU, so don't need such conditions at all.

Somehow, I feel no compulsion to remove the CONFIG_HAVE_MLOCK* lines from
169 defconfigs: leave those to evolve in due course.
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Izik Eidus <ieidus@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Nick Piggin <npiggin@suse.de>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 53d0422c ("tracing: Convert some kmem events to DEFINE_EVENT")
moved the kmem tracepoint creation from util.c to page_alloc.c,
but forgot to move the exports.

Move them back.

Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
LKML-Reference: <4B0E286A.2000405@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Use DECLARE_EVENT_CLASS to remove duplicate code:

   text    data     bss     dec     hex filename
 333987   69800   27228  431015   693a7 mm/built-in.o.old
 330030   69800   27228  427058   68432 mm/built-in.o

8 events are converted:

  kmem_alloc: kmalloc, kmem_cache_alloc
  kmem_alloc_node: kmalloc_node, kmem_cache_alloc_node
  kmem_free: kfree, kmem_cache_free
  mm_page: mm_page_alloc_zone_locked, mm_page_pcpu_drain

No change in functionality.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
LKML-Reference: <4B0E286A.2000405@cn.fujitsu.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Commit 341ce06f ("page allocator:
calculate the alloc_flags for allocation only once") altered watermark
logic slightly by allowing rt_tasks that are handling an interrupt to set
ALLOC_HARDER.  This patch brings the watermark logic more in line with
2.6.30.

This change results in a reduction of the number high-order GFP_ATOMIC
allocation failures reported.  See
http://www.gossamer-threads.com/lists/linux/kernel/1144153

[rientjes@google.com: Spotted the problem]
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Reviewed-by: NPekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: NRik van Riel <riel@redhat.com>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>