Revert the SAI's endianess for fifo data to/from DMA engine.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This is maybe one bug or a limitation of the hardware that the {T,R}CR2's
Synchronous Mode bits must be set as late as possible, or the SAI device
maybe hanged up, and there has not any explaination about this limitation
in the SAI Data Sheet.

And the {T,R}CR2's Synchronous Mode bits must be set at the same time whether
for Tx or Rx stream.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Enables/Disables the corresponding data channel for tx/rx operation.
A channel must be enabled before its FIFO is accessed, and then disable
it when tx/rx is stopped or idle.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Because we cannot make sure which one of _dai_fmt() and _dai_sysclk()
will be firstly called. So move the RCSR/TCSR and TCR1/RCR1's
initialization to _dai_probe(), and this can make sure that before any
of {T,R}CR{1~5} register to be set the RCSR/TCSR's RE/TE bit has been
cleared for the hareware limitation.
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Generally we would write code for local variable like:
static new_func()
{
	struct xxx *yyy;
	...
	int ret;
}

But this driver only follows this pattern for some functions, not all.
Thus this patch sorts the local variable in the general way.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Reviewed-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Since using dev_err() there's no need to mention SAI any more, it will
print the full name of the driver -- fsl_sai.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Reviewed-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

We can save this ret to make the code neater.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Reviewed-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

SAi only supports two data channels on hardware level and the driver also does
register the min->1 and max->2, so no need to check channels.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Reviewed-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Use common helper function snd_pcm_format_width() to make code neater.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Reviewed-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

There are two functions haven't clk_disable_unprepare() if having error.
Thus fix them.
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Reviewed-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Makes the code slightly shorter
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Makes the code slightly shorter
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

There is no need of this function and makes the code slightly shorter
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This adds Freescale SAI ASoC Audio support.
This implementation is only compatible with device tree definition.
Features:
o Supports playback/capture
o Supports 16/20/24 bit PCM
o Supports 8k - 96k sample rates
o Supports master and slave mode.
Signed-off-by: NAlison Wang <b18965@freescale.com>
Signed-off-by: NXiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>