Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 02 12月, 2006 1 次提交
    • I
      PCI: switch pci_{enable,disable}_device() to be nestable · bae94d02
      由 Inaky Perez-Gonzalez 提交于 
      Changes the pci_{enable,disable}_device() functions to work in a
nested basis, so that eg, three calls to enable_device() require three
calls to disable_device().

The reason for this is to simplify PCI drivers for
multi-interface/capability devices. These are devices that cram more
than one interface in a single function. A relevant example of that is
the Wireless [USB] Host Controller Interface (similar to EHCI) [see
http://www.intel.com/technology/comms/wusb/whci.htm]. 

In these kind of devices, multiple interfaces are accessed through a
single bar and IRQ line. For that, the drivers map only the smallest
area of the bar to access their register banks and use shared IRQ
handlers. 

However, because the order at which those drivers load cannot be known
ahead of time, the sequence in which the calls to pci_enable_device()
and pci_disable_device() cannot be predicted. Thus:

1. driverA     starts     pci_enable_device()
2. driverB     starts     pci_enable_device()
3. driverA     shutdown   pci_disable_device()
4. driverB     shutdown   pci_disable_device()

between steps 3 and 4, driver B would loose access to it's device,
even if it didn't intend to.

By using this modification, the device won't be disabled until all the
callers to enable() have called disable().

This is implemented by replacing 'struct pci_dev->is_enabled' from a
bitfield to an atomic use count. Each caller to enable increments it,
each caller to disable decrements it. When the count increments from 0
to 1, __pci_enable_device() is called to actually enable the
device. When it drops to zero, pci_disable_device() actually does the
disabling.

We keep the backend __pci_enable_device() for pci_default_resume() to
use and also change the sysfs method implementation, so that userspace
enabling/disabling the device doesn't disable it one time too much.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      bae94d02
  3. 27 9月, 2006 1 次提交
  5. 13 7月, 2006 1 次提交
    • K
      [PATCH] PCI: PCIE power management quirk · ffadcc2f
      由 Kristen Carlson Accardi 提交于 
      When changing power states from D0->DX and then from DX->D0, some
Intel PCIE chipsets will cause a device reset to occur.  This will
cause problems for any D State other than D3, since any state
information that the driver will expect to be present coming from
a D1 or D2 state will have been cleared.  This patch addes a
flag to the pci_dev structure to indicate that devices should
not use states D1 or D2, and will set that flag for the affected
chipsets.  This patch also modifies pci_set_power_state() so that
when a device driver tries to set the power state on
a device that is downstream from an affected chipset, or on one
of the affected devices it only allows state changes to or
from D0 & D3.  In addition, this patch allows the delay time
between D3->D0 to be changed via a quirk.  These chipsets also
need additional time to change states beyond the normal 10ms.
Signed-off-by: NKristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      ffadcc2f
  7. 28 6月, 2006 1 次提交
  9. 22 6月, 2006 1 次提交
  11. 15 4月, 2006 1 次提交
  13. 24 3月, 2006 1 次提交
  15. 10 1月, 2006 1 次提交
  17. 05 1月, 2006 1 次提交
  19. 29 10月, 2005 1 次提交
    • B
      [PATCH] PCI: Block config access during BIST · e04b0ea2
      由 Brian King 提交于 
      Some PCI adapters (eg.  ipr scsi adapters) have an exposure today in that they
issue BIST to the adapter to reset the card.  If, during the time it takes to
complete BIST, userspace attempts to access PCI config space, the host bus
bridge will master abort the access since the ipr adapter does not respond on
the PCI bus for a brief period of time when running BIST.  On PPC64 hardware,
this master abort results in the host PCI bridge isolating that PCI device
from the rest of the system, making the device unusable until Linux is
rebooted.  This patch is an attempt to close that exposure by introducing some
blocking code in the PCI code.  When blocked, writes will be humored and reads
will return the cached value.  Ben Herrenschmidt has also mentioned that he
plans to use this in PPC power management.
Signed-off-by: NBrian King <brking@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/pci/access.c    |   89 ++++++++++++++++++++++++++++++++++++++++++++++++
 drivers/pci/pci-sysfs.c |   20 +++++-----
 drivers/pci/pci.h       |    7 +++
 drivers/pci/proc.c      |   28 +++++++--------
 drivers/pci/syscall.c   |   14 +++----
 include/linux/pci.h     |    7 +++
 6 files changed, 134 insertions(+), 31 deletions(-)
      e04b0ea2
  21. 10 9月, 2005 1 次提交
  23. 17 8月, 2005 2 次提交
  25. 12 7月, 2005 2 次提交
  27. 18 5月, 2005 1 次提交
  29. 17 4月, 2005 1 次提交
    • L
      Linux-2.6.12-rc2 · 1da177e4
      由 Linus Torvalds 提交于 
      Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
      1da177e4