Extend struct flow_block_offload with "unlocked_driver_cb" flag to allow
registering and unregistering block hardware offload callbacks that do not
require caller to hold rtnl lock. Extend tcf_block with additional
lockeddevcnt counter that is incremented for each non-unlocked driver
callback attached to device. This counter is necessary to conditionally
obtain rtnl lock before calling hardware callbacks in following patches.

Register mlx5 tc block offload callbacks as "unlocked".
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/cirrus/cs89x0.c: In function 'cs89x0_platform_probe':
drivers/net/ethernet/cirrus/cs89x0.c:1847:20: warning:
 variable 'lp' set but not used [-Wunused-but-set-variable]
Reported-by: NHulk Robot <hulkci@huawei.com>
Fixes: 6751edeb ("cirrus: cs89x0: Use managed interfaces")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit ee641b0c.

Actually it is not clear whether this register read is not
needed for it's HW side effects or not.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c: In function mtk_handle_irq:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:1951:6: warning: variable status set but not used [-Wunused-but-set-variable]

Fixes: 296c9120 ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Signed-off-by: NMao Wenan <maowenan@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SFPs can report two different power values, the transmit power and the
receive power. Add labels to make it clear which is which. Also add
labels to the other sensors, VCC power supply, bias and module
temperature.

sensors(1) now shows:

sff2-isa-0000
Adapter: ISA adapter
VCC:          +3.23 V
temperature:  +33.4 C
TX_power:    276.00 uW
RX_power:     20.00 uW
bias:         +0.01 A
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent commit added logic to determine the appropriate statistics block
size to allocate and the size is stored in bp->hw_ring_stats_size.  But
if the firmware spec is older than 1.6.0, it is 0 and not initialized.
This causes the allocation to fail with size 0 and bnxt_open() to
abort.  Fix it by always initializing bp->hw_ring_stats_size to the
legacy default size value.

Fixes: 4e748506 ("bnxt_en: Allocate the larger per-ring statistics block for 57500 chips.")
Reported-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Tested-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
 warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
 warning: tuple_key_info defined but not used [-Wunused-const-variable=]

The two variable is only used in hclge_main.c,
so just move the definition over there.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Aaro this patch causes network problems on
MIPS Loongson platform. Therefore revert it.

Fixes: f072218c ("r8169: remove not needed call to dma_sync_single_for_device")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reported-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return code value could be non deterministic in case of wrong size read.
With this patch, if such error occurs, set rc to be -EIO.

In addition, mlx5_hv_config_common() supports reading of
HV_CONFIG_BLOCK_SIZE_MAX bytes only, fix to early return error with
bad input.

Fixes: 913d14e8 ("net/mlx5: Add wrappers for HyperV PCIe operations")
Reported-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper function "rtl_eee_enable" for setting EEE. Besides, I
move r8153_eee_en() and r8153b_eee_en(). And, I remove r8152b_enable_eee(),
r8153_set_eee(), and r8153b_set_eee().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saving the settings of EEE to avoid they become the default settings
after reset_resume().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a VSI is not using a unicast filter or did not configure that
particular unicast filter, driver should not allow it to be removed
by the rogue VSI.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VSI, especially VF could request to add or remove filter for another VSI,
driver should really guide such request and disallow it.
However, instead of returning error for such malicious request, driver
can simply return success.

In addition, we are not tracking number of MAC filters configured per
VF correctly - and this leads to issue updating VF MAC filters whenever
they were removed and re-configured via bringing VF interface down and
up. Also, since VF could send request to update multiple MAC filters at
once, driver should program those filters individually in the switch, in
order to determine which action resulted to error, and communicate
accordingly to the VF.

So, with this changes, we now track number of filters added right from
when VF resources allocation is done, and could properly add filters for
both trusted and non_trusted VFs, without MAC filters mis-match issue in
the switch...

Also refactor code, so that driver can use new function to add or remove
MAC filters.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Users expect ethtool statistics to be updated on-demand when invoking
'ethtool -S <iface>' instead of providing a snapshot of statistics taken
once a second (the frequency of the watchdog task where stats are currently
updated).  Update stats every time 'ethtool -S <iface>' is run.

Also, fix an indentation style issue and an unnecessary local variable
initialization in ice_get_ethtool_stats() discovered while investigating
the subject issue.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the assignment to local variables after validation.

Remove unnecessary checks in ice_vc_process_vf_msg() as the respective
functions are now performing the checks.
Signed-off-by: N"Amruth G.P" <amruth.gouda.parameshwarappa@intel.com>
Signed-off-by: NNitesh B Venkatesh <nitesh.b.venkatesh@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver should never clear the auto_fec_enable bit.
Signed-off-by: NChinh T Cao <chinh.t.cao@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When checking the PHY for status, by specification, the driver
should be using "topology" mode when querying the module type.
Signed-off-by: NChinh T Cao <chinh.t.cao@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some circumstances, VF devices can be deactivated while a message is
in-flight. In that case, a series of scary error message will be
printed in the log. Since these are actually harmless, check for this
case and suppress them. No harm, no foul.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current flag name of "enable-fw-lldp" is a bit cumbersome.

Change priv-flag name to "fw-lldp-agent" with a value of on or
off.  This is more straight-forward in meaning.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The virtchnl interface provides a mechanism for a VF driver to request
head writeback support. This feature is deprecated as of AVF 1.0, but
older versions of a VF driver may still attempt to request the mode.

Since the ice hardware does not support head writeback, we should not
accept Tx queue configuration which attempts to enable it.

Currently, the driver simply assumes that the headwb_enabled bit will
never be set.

If a VF driver does request head writeback, the configuration will
return successfully, even though head writeback is not enabled. This
leaves the VF driver in a non functional state since it is assuming to
be operating in head writeback mode.

Fix the PF driver to reject any attempt to setup headwb_enabled.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In rebuild DCB desired_dcbx_cfg was copy to local_dcbx_cfg, but
if DCBX mode is IEEE desired_dcbx_cfg is not initialized by DCBX
config from FW. Change logic to copy config value only if mode is
set to CEE.

If driver copy desired_dcbx_cfg to local_dcbx_cfg in IEEE mode there
is problem with globr. System is frozen after two or more globr.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a port is not cabled, but DCBx is enabled in the
firmware, the status of DCBx will be NOT_STARTED.  This
is a valid state for FW enabled and should not be
treated as a is_fw_lldp true automatically.

Add the code to treat NOT_STARTED as another valid state.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we will call synchronize_irq() from the host for VF's. This is
not correct, so don't allow it.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, only the DCBx status is taken into account to
determine if FW LLDP is possible.  But there are NVM version
coming out with DCBx enabled, and FW LLDP disabled.  This
is causing errors where the driver sees that DCBx is not
disabled, and then tries to register for LLDP MIB change
events, and fails.

Change the logic to detect both DCBx and LLDP states in the
FW engine.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For control packets (i.e. LLDP packets) to be able to egress
from the main VSI, a bit has to be set in the TX_descriptor.
This should only be done for the main VSI and only if the
FW LLDP agent is disabled.  A bit to allow this also has to
be set in the VSI context.

Add the logic to add the necessary bits in the VSI context
for the PF_VSI and the TX_descriptors for control packets
egressing the PF_VSI.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Acked-by: NSean Nyekjaer <sean@geanix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two
staged access model in order to increase the address space.

This patch adds support for C45 MDIO read and write accesses, which are
used whenever the MII_ADDR_C45 flag in the regnum argument is set.
In case it is not set, C22 accesses are used as before.
Signed-off-by: NMarco Hartmann <marco.hartmann@nxp.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed a bug where driver was breaking out of the loop and
reporting an error without retrying first.
Signed-off-by: NMarcin Formela <marcin.formela@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a function to read NVM module data and uses it to
read current LLDP agent configuration from NVM API version 1.8.
Signed-off-by: NSylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver waits after issuing a reset. When a reset takes too long a driver
gives up. Implemented by invoking PF reset in a loop. After defined
number of unsuccessful PF reset trials it returns error.
Without this patch PF reset fails when NIC is in recovery mode.

So make i40e_set_mac_type() public. i40e driver requires i40e_set_mac_type()
to be public. It is required for recovery mode handling. Without this patch
recovery mode could not be detected in i40e_probe().
Signed-off-by: NPiotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes function i40e_update_dcb_config(). Instead of
i40e_update_dcb_config() we use i40e_init_dcb(), which implements the
correct NVM read.
Signed-off-by: NGrzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add update to the VSI pointer passed to the i40e_set_vf_mac function.
If VF is in reset state the driver waits in i40e_set_vf_mac function
for the reset to be complete, yet after reset the vsi pointer
that was passed into this function is no longer valid.

The patch updates local VSI pointer directly from pf->vsi array,
by using the id stored in VF pointer (lan_vsi_idx).

Without this commit the driver might occasionally invoke general
protection fault in kernel and disable the OS entirely.
Signed-off-by: NSlawomir Laba <slawomirx.laba@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The stats structure for the VEB switch statistics is reset periodically,
but the tc_stats are not reset at the same time.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Upcoming FW increment API version to 1.9 due to Extend PHY access AQ
command support. SW is ready for that support as well.
Signed-off-by: NPiotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Function check_recovery_mode had wrong if statement.
Now we check proper FWS1B register values, which are responsible for
the recovery mode. Recovery mode has 4 values for x710 and 2 for x722.
That's why we need 6 different flags which are defined in the code.
Now in the if statement, we recognize type of mac address
and register value.
Without those changes driver could show wrong state.
Signed-off-by: NAdrian Podlawski <adrian.podlawski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds "drop mode" parameter to set mac config AQ command.
This bit controls the behavior when a no-drop packet is blocking a TC
queue.
0 – The PF driver is notified.
1 – The blocking packet is dropped and then the PF driver is notified.
Signed-off-by: NSylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes following error reported by cppcheck:
(error) Shifting signed 32-bit value by 31 bits is undefined behaviour
Signed-off-by: NBeilei Xing <beilei.xing@intel.com>
Signed-off-by: NFerruh Yigit <ferruh.yigit@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>