This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Acked-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

A few function prototypes were left in header files during code re-
organization. Delete them.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:

* tunning off L1 data cache and the MMU
* putting SDRAM into self-refresh
* storing some EMC registers and SCLK burst policy
* switching CPU to CLK_M (12MHz OSC)
* switching SCLK to CLK_S (32KHz OSC)
* tunning off PLLM, PLLP and PLLC
* shutting off the CPU rail

The sequence of LP1 resuming:

* re-enabling PLLM, PLLP, and PLLC
* restoring some EMC registers and SCLK burst policy
* setting up CCLK burst policy to PLLP
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41

Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored, CCLK burst policy be set in PLLP. Then jumping to
"tegra_resume" that was expected to be stored in PMC_SCRATCH41 to restore
CPU context and back to kernel.

Based on the work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:

* tunning off L1 data cache and the MMU
* storing some EMC registers, DPD (deep power down) status, clk source of
  mselect and SCLK burst policy
* putting SDRAM into self-refresh
* switching CPU to CLK_M (12MHz OSC)
* tunning off PLLM, PLLP, PLLA, PLLC and PLLX
* switching SCLK to CLK_S (32KHz OSC)
* shutting off the CPU rail

The sequence of LP1 resuming:

* re-enabling PLLM, PLLP, PLLA, PLLC and PLLX
* restoring the clk source of mselect and SCLK burst policy
* setting up CCLK burst policy to PLLX
* restoring DPD status and some EMC registers
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41

Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored, CCLK burst policy be set in PLLX. Then jumping to
"tegra_resume" that was expected to be stored in PMC_SCRATCH41 to restore
CPU context and back to kernel.

Based on the work by: Scott Williams <scwilliams@nvidia.com>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The LP1 suspending mode on Tegra means CPU rail off, devices and PLLs are
clock gated and SDRAM in self-refresh mode. That means the low level LP1
suspending and resuming code couldn't be run on DRAM and the CPU must
switch to the always on clock domain (a.k.a. CLK_M 12MHz oscillator). And
the system clock (SCLK) would be switched to CLK_S, a 32KHz oscillator.
The LP1 low level handling code need to be moved to IRAM area first. And
marking the LP1 mask for indicating the Tegra device is in LP1. The CPU
power timer needs to be re-calculated based on 32KHz that was originally
based on PCLK.

When resuming from LP1, the LP1 reset handler will resume PLLs and then
put DRAM to normal mode. Then jumping to the "tegra_resume" that will
restore full context before back to kernel. The "tegra_resume" handler
was expected to be found in PMC_SCRATCH41 register.

This is common LP1 procedures for Tegra, so we do these jobs mainly in
this patch:
* moving LP1 low level handling code to IRAM
* marking LP1 mask
* copying the physical address of "tegra_resume" to PMC_SCRATCH41
* re-calculate the CPU power timer based on 32KHz
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
[swarren, replaced IRAM_CODE macro with IO_ADDRESS(TEGRA_IRAM_CODE_AREA)]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

tegra_{set,clear}_cpu_in_lp2 can easily determine which CPU ID they are
running on; there is no need to pass the CPU ID into those functions.
So, remove their CPU ID function parameter.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This fixes the building error when the PM_SLEEP is disabled. The fucntional
defintion of "tegra_pm_validate_suspend_mode" without "static inline"
would become a multiple definition error.
Reported-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

After the patch series for system suspending support, tegra_idle_lp2_last()
no longer uses its parameters cpu_on_time or cpu_off_time, so remove them.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Adding suspend to RAM support for Tegra platform. There are three suspend
mode for Tegra. The difference were below.

* LP2: CPU voltage off
* LP1: CPU voltage off, DRAM in self-refresh
* LP0: CPU + Core voltage off, DRAM in self-refresh

After this patch, the LP2 suspend mode will be supported.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The L2 RAM is in different power domain from the CPU cluster. So the
L2 content can be retained over CPU suspend/resume. To do that, we
need to disable L2 after the MMU is disabled, and enable L2 before
the MMU is enabled. But the L2 controller is in the same power domain
with the CPU cluster. We need to restore it's settings and re-enable
it after the power be resumed.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This is a power gating idle mode. It support power gating vdd_cpu rail
after all cpu cores in "powered-down" status. For Tegra30, the CPU0 can
enter this state only when all secondary CPU is offline. We need to take
care and make sure whole secondary CPUs were offline and checking the
CPU power gate status. After that, the CPU0 can go into "powered-down"
state safely. Then shut off the CPU rail.

Be aware of that, you may see the legacy power state "LP2" in the code
which is exactly the same meaning of "CPU power down".

Base on the work by:
Scott Williams <scwilliams@nvidia.com>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This supports power-gated idle on secondary CPUs for Tegra30. The
secondary CPUs can go into powered-down state independently. When
CPU goes into this state, it saves it's contexts and puts itself
to flow controlled WFI state. After that, it will been power gated.

Be aware of that, you may see the legacy power state "LP2" in the
code which is exactly the same meaning of "CPU power down".

Based on the work by:
Scott Williams <scwilliams@nvidia.com>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

During pinctrl_get(), if the client device has a device tree node, look
for the common pinctrl properties there. If found, parse the referenced
device tree nodes, with the help of the pinctrl drivers, and generate
mapping table entries from them.

During pinctrl_put(), free any results of device tree parsing.
Acked-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This PMC driver is enough to parse the nvidia,invert-interrupt property
from device tree, and configure the PMC's to honor that.

In the future, this file could expand to centralize all other PMC accesses
within the mach-tegra code.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite.  Remove arm_machine_restart() as this function
no longer does anything useful.

For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions.  As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds basic support for the Calxeda Highbank platform.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Reviewed-by: NJamie Iles <jamie@jamieiles.com>
Reviewed-by: NShawn Guo <shawn.guo@linaro.org>

The IPS driver is designed to be able to run detached from i915 and
just not enable GPU turbo in that case, in order to avoid module
dependencies between the two drivers.  This means that we don't know
what the load order between the two is going to be, and we had
previously only supported IPS after (optionally) i915, but not i915
after IPS.  If the wrong order was chosen, you'd get no GPU turbo, and
something like half the possible graphics performance.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Signed-off-by: NAvi Kivity <avi@redhat.com>

After moving the the include files there were a few clean-ups:

1) Some files used #include <asm-ia64/xyz.h>, changed to <asm/xyz.h>

2) Some comments alerted maintainers to look at various header files to
make matching updates if certain code were to be changed. Updated these
comments to use the new include paths.

3) Some header files mentioned their own names in initial comments. Just
deleted these self references.
Signed-off-by: NTony Luck <tony.luck@intel.com>

Three header files are added:
asm-ia64/kvm.h
asm-ia64/kvm_host.h
asm-ia64/kvm_para.h
Signed-off-by: NXiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>