This patch removes the chip select function.  Chip select should instead be
supported using GPIOs, defining the DT entry "cs-gpios", and letting the SPI
core assert/deassert the chip select as it sees fit.

The chip select control inside the controller is buggy.  It is supposed to
automatically assert the chip select based on the activity in the controller,
but it is buggy and doesn't work at all.  So instead we elect to use GPIOs.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

P2WI (Push/Pull 2 Wire Interface) is an SMBus like bus used to communicate
with some PMICs (like the AXP221).

Document P2WI DT bindings which are pretty much the same as the one defined
for the marvell's mv64xxx controller.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Driver for the native I2C adapter found in Rockchip RK3xxx SoCs.

Configuration is only possible through devicetree. The driver is
interrupt driven and supports the I2C_M_IGNORE_NAK mangling bit.
Signed-off-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Document new compatible strings for clock provided by the PRCM
(Power/Reset/Clock Management) unit.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

Support for the USB gates and resets on A31 has been recently added
using a new compatible, so let's document it here.
Signed-off-by: NEmilio López <emilio@elopez.com.ar>

This commit documents the new support for "marvell,armada-{375,380}-wdt"
compatible strings and the extra 'reg' entry requirement.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This panel is used by nyan-big and can be supported by the simple-panel
driver.
Signed-off-by: NStéphane Marchesin <marcheu@chromium.org>
[treding@nvidia.com: add device tree binding document]
Signed-off-by: NThierry Reding <treding@nvidia.com>

This enables the setting of a custom clock name for the clock provided by
the hym8563 rtc.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: NLoc Ho <lho@apm.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

MPU DPLL on OMAP5, DRA75x, DRA72x has a limitation on the maximum
frequency it can be locked at. Duty Cycle Correction circuit is used
to recover a correct duty cycle for achieving higher frequencies
(hardware internally switches output to M3 output(CLKOUTHIF) from M2
output (CLKOUT)).

So provide support to setup required data to handle Duty cycle by
the setting up the minimum frequency for DPLL. 1.4GHz is common
for all these devices and is based on Technical Reference Manual
information for OMAP5432((SWPU282U) chapter 3.6.3.3.1 "DPLLs Output
Clocks Parameters", and equivalent information from DRA75x, DRA72x
documentation(SPRUHP2E, SPRUHI2P).
Signed-off-by: NNishanth Menon <nm@ti.com>
[t-kristo@ti.com: updated for latest dpll init API call]
Signed-off-by: NTero Kristo <t-kristo@ti.com>

This patch provides the documentation of the device bindings
for the AMD 10GbE platform driver.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DSI controllers are powered by a (typically 1.2V) regulator. Usually
this is always on, so there was no need to support enabling or disabling
it thus far. But in order not to consume any power when DSI is inactive,
give the driver a chance to enable or disable the supply as needed.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Revert commit 18ebc0f4 "drm/tegra: hdmi: Enable VDD earlier for
hotplug/DDC" and instead add a new supply for the +5V pin on the HDMI
connector.

The vdd-supply property refers to the regulator that supplies the
AVDD_HDMI input on Tegra, rather than the +5V HDMI connector pin. This
was never a problem before, because all boards had that pin hooked up to
a regulator that was always on. Starting with Dalmore and continuing
with Venice2, the +5V pin is controllable via a GPIO. For reasons
unknown, the GPIO ended up as the controlling GPIO of the AVDD_HDMI
supply in the Dalmore and Venice2 DTS files. But that's not correct.
Instead, a separate supply must be introduced so that the +5V pin can be
controlled separately from the supplies that feed the HDMI block within
Tegra.

A new hdmi-supply property is introduced that takes the place of the
vdd-supply and vdd-supply is only enabled when HDMI is enabled rather
than all the time.
Signed-off-by: NThierry Reding <treding@nvidia.com>

This panel is sold by Toradex for Colibri T20/T30 and Apalis T30
evaluation kits.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The EDT ETM0700G0DH6 and ET070080DH6 are 7" 800x480 panels,
which can be supported by the simple panel driver.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The Allwinner sunxi mmc host uses dma in bus-master mode using a built-in
designware idmac controller, which is identical to the one found in the mmc-dw
hosts. However the rest of the host is not identical to mmc-dw, it deals with
sending stop commands in hardware which makes it significantly different
from the mmc-dw devices.
Signed-off-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch>
[hdegoede@redhat.com: various cleanups and fixes]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NChris Ball <chris@printf.net>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The glue around the core designware IP is significantly different between
the Exynos and i.MX implementation, which is reflected in the DT bindings.

This changes the i.MX6 binding to reuse as much as possible from the common
designware binding and removes old cruft.

I removed the optional GPIOs with the following reasoning:
- disable-gpio: endpoint specific GPIO, not currently wired up in any code.
  Should be handled by the PCI device driver, not the host controller
  driver.
- wake-up-gpio: same as above.
- power-on-gpio: No user in any upstream DT.  This should be handled by a
  regulator which shouldn't be controlled by the host driver, but rather by
  the PCI device driver.

[bhelgaas: whitespace fixes]
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The Keystone II devices have a set of registers that are used to control
the status of its peripherals. This node is intended to allow access to
this functionality.
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

On ARM Chromebooks we have a few devices that are accessed by both the
AP (the main "Application Processor") and the EC (the Embedded
Controller).  These are:
* The battery (sbs-battery).
* The power management unit tps65090.

On the original Samsung ARM Chromebook these devices were on an I2C
bus that was shared between the AP and the EC and arbitrated using
some extranal GPIOs (see i2c-arb-gpio-challenge).

The original arbitration scheme worked well enough but had some
downsides:
* It was nonstandard (not using standard I2C multimaster)
* It only worked if the EC-AP communication was I2C
* It was relatively hard to debug problems (hard to tell if i2c issues
  were caused by the EC, the AP, or some device on the bus).

On the HP Chromebook 11 the design was changed to:
* The AP/EC comms were still i2c, but the battery/tps65090 were no
  longer on the bus used for AP/EC communication.  The battery was
  exposed to the AP through a limited i2c tunnel and tps65090 was
  exposed to the AP through a custom Linux driver.

On the Samsung ARM Chromebook 2 the scheme is changed yet again, now:
* The AP/EC comms are now using SPI for faster speeds.
* The EC's i2c bus is exposed to the AP through a full i2c tunnel.

The upstream "tegra124-venice2" uses the same scheme as the Samsung
ARM Chromebook 2, though it has a different set of components on the
other side of the bus.

This driver supports the scheme used by the Samsung ARM Chromebook 2.
Future patches to this driver could add support for the battery tunnel
on the HP Chromebook 11 (and perhaps could even be used to access
tps65090 on the HP Chromebook 11 instead of using a special driver,
but I haven't researched that enough).
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Document DT bindings of the PRCM (Power/Reset/Clock Management) unit.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In certain boards the source for the clk32k clock can be gated. In these
boards the clk32k clock can be provided to the driver and it is going to be
enabled/disabled when it is needed.
If the clk32k clock is not provided the driver will assume that it is always
running.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a driver for the Renesas usdhi6rol0 SD/SDIO host controller
in both PIO and DMA modes.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NChris Ball <chris@printf.net>

Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Exynos drm hdmi driver used to get dummy hdmiphy clock to
control the PMU bit for hdmiphy. This bit needs to be set
before setting any resolution to hdmi hardware. This was
handled using dummy hdmiphy clock which is removed here.

PMU is already defined as system controller for exynos
SoCs. Hdmi driver is modified to control the phy enable bit
inside PMU using regmap interfaces.

Devicetree binding document for hdmi is also updated.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Enable support for hdmi for exynos5420 hdmiphy. Add
compatible string in the of_match table. Also added
hdmiphy configuration values for exynos5420.
Signed-off-by: NRahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: NShirish S <s.shirish@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Certain bridge chips use a GPIO to indicate the cable status instead
of the I_DP_HPD pin.  This adds an optional device-tree property,
"samsung,hpd-gpio", to the exynos-dp controller which indicates that
the specified GPIO should be used for hotplug detection.
The GPIO is then set up as an edge-triggered interrupt where the
rising edge indicates hotplug-in and the falling edge indicates hotplug-out.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NAjay Kumar <ajaykumar.rs@samsung.com>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The correct name of the third clock is hda2codec_2x.
Signed-off-by: NDylan Reid <dgreid@chromium.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add support for a generic PCI host controller, such as a
firmware-initialised device with static windows or an emulation by
something such as kvmtool.

The controller itself has no configuration registers and has its address
spaces described entirely by the device-tree (using the bindings from
ePAPR).  Both CAM and ECAM are supported for Config Space accesses.

Add corresponding documentation for the DT binding.

[bhelgaas: currently uses the ARM-specific pci_common_init_dev() interface]
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NLiviu Dudau <liviu.dudau@arm.com>

This patch add pmusysreg node for Exynos3250 to access PMU
(Power Management Unit) register in a centralized way using
syscon driver.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The EXYNOS5410 clocks are statically listed and registered
using the Samsung specific common clock helper functions.
Signed-off-by: NTarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: NVyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

A new PLL (gpll4) is added on msm8974 PRO devices to support a
faster sdc1 clock rate. Add support for this and the two new sdcc
cal clocks.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This patch adds pin definitiones for the MSM8x74 TLMM.
New definitions include:

BLSP devices (I2C, UART, SPI, and UIM), mi2s, gp clk,
pdm, gcc clk, cci_timer, cci_i2c, cam_clk, hsic, tsif,
sdc3, sdc4, and other assorted pins.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Acked-By: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds DT support to the tsc2005 touchscreen driver. It also adds
regulator support to the driver if booted via DT.
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add common DT binding documentation for touchscreen devices and
implement input_parse_touchscreen_of_params, which parses the common
properties and configures the input device accordingly.

The method currently does not interpret the axis inversion properties,
since there is no matching flag in the generic linux input device.
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The generic SPMI example was missing an equal sign in the assignment
of the #size-cells property.
Signed-off-by: NJosh Cartwright <joshc@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit extends the compatible string list of the xhci-platform
binding with the new "renesas,xhci-r8a7790" and "renesas,xhci-r8a7791"
compatible strings. It is used to describe the xHCI controller which
is available in the R-Car H2 and M2 SoCs.
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

8250 uart driver currently supports only software assisted hw flow
control. The software assisted hw flow control maintains a hw_stopped
flag in the tty structure to stop and start transmission and use modem
status interrupt for the event to drive the handshake signals. This is
not needed if hw has flow control capabilities. This patch adds a
DT attribute for enabling hw flow control for a uart port. Also skip
stop and start if this flag is present in flag field of the port
structure.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On sam9x5, dedicated CTS (and RTS) pins are unusable together with the
LCDC, the EMAC, or the MMC because they share the same line.

Moreover, the USART controller doesn't handle DTR/DSR/DCD/RI signals,
so we have to control them via GPIO.

This patch permits to use GPIOs to control the CTS/RTS/DTR/DSR/DCD/RI
signals.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>