The am53c974 is a re-implementation of the tmscsim driver,
and provides the same functionality.
So remove the tmscsim driver and make am53c974 an alias to tmscsim.
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

CONFIG2_FENAB ('feature enable') changed definition between chip
revisions, from 'Latch SCSI Phase' to 'Latch SCSI Phase, display
chip ID upon reset, and enable 24 bit addresses'.
So only enable it for am53c974 where we know what it's doing.
Acked-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

On PCscsi, the FENAB configuration also enables 24-bit DMA
transfer lengths (and provides the chip id in TCHI after reset).
We want to be able to enable this parameter from the DMA driver.

Check if the caller of scsi_esp_register provided a value for esp->config2.
If this is the case, assume this is not an ESP100, skip the detection
phase and leave esp->config2 untouched.  It will be used in esp_reset_esp.
Reviewed-by: NHannes Reinecke <hare@suse.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The am53c974 returns the same ID as the FAS236, but implements
things slightly differently. So detect the am53c974 by checking
for ESP_CONFIG4 register.
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The am53c974 has an design issue where a single byte might be
left in the SCSI FIFO after a DMA transfer.
As the handling code is currently untested add a WARN_ON()
statement here.
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch adds a new implementation for the Tekram DC-390T /
AMD AM53c974 SCSI controller, based on the generic
esp_scsi infrastructure.
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Using DMA for command submission has the drawback that it might
generate additional DMA completion interrupts after the command
has been submitted to the device.
Additionally the am53c974 has a design flaw causing it
to generate spurious interrupts even though DMA completion
interrupts are not enabled.
This can be avoided by using the FIFO for command submission.
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

A read to ESP_INTRPT will clear ESP_STATUS and ESP_SSTEP. So read
all status registers in one go to avoid losing information.
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add new debug definitions for event and command logging.
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Use dev_printk functions for correct device annotations.
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add a field 'num_tags' to the esp structure to allow drivers
to overwrite the number of avialable tags if required.
Default is ESP_DEFAULT_TAGS.
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Remove overly verbose debugging output that pokes into mid-layer internal
structures that looks like copy & paste from the mpt2/3 drivers.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Merge two functions, and remove overly verbose debugging output that pokes
into mid-layer internal structures.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Merge two functions, and remove overly verbose debugging output that pokes
into mid-layer internal structures.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

We won't ever queue more commands than the host allows.  Instead of
letting drivers either reject or ignore this case handle it in
common code.  Note that various driver use internal constant or
variables that are assigned to both shost->can_queue and checked
in ->change_queue_depth - I did remove those checks as well.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.

Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NVenkatesh Srinivas <venkateshs@google.com>

James Smart said the userspace to consume these events never emerged.  Given
that these get in the way of the following patches remove support for them.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Acked-by: NJames Smart <james.smart@emulex.com>

Do not process any SCSI and IOCTL command further (return them with
appropriate return values to callers), while driver removal is in
progress or PCI shutdown is invoked.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch addresses few endianness related bug fixes.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Corrected wait_event() call which was waiting for wrong completion
status (0xFF).
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

In OCR(Online Controller Reset) path, driver sets adapter state to
MEGASAS_HBA_OPERATIONAL before getting new RAID map.  There will be a small
window where IO will come from OS with old RAID map. This patch will update
adapter state to MEGASAS_HBA_OPERATIONAL, only after driver has new RAID
map to avoid any IOs getting build using old RAID map.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

In OCR (Online Controller Reset) path, driver sets adapter state to
MEGASAS_HBA_OPERATIONAL before getting new RAID map.  There will be a small
window where IO will come from OS with old RAID map.  This patch will
update adapter state to MEGASAS_HBA_OPERATIONAL, only after driver has new
RAID map to avoid any IOs getting build using old RAID map.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: NKashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Update MAINTAINERS list and copyright information for megaraid_sas driver.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Update driver version and remove some meta data (release date and extended
version) about megaraid_sas driver.
Signed-off-by: NSumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch improves the Fibre Channel port scan behaviour of the zfcp lldd.
Without it the zfcp device driver may churn up the storage area network by
excessive scanning and scan bursts, particularly in big virtual server
environments, potentially resulting in interference of virtual servers and
reduced availability of storage connectivity.

The two main issues as to the zfcp device drivers automatic port scan in
virtual server environments are frequency and simultaneity.
On the one hand, there is no point in allowing lots of ports scans
in a row. It makes sense, though, to make sure that a scan is conducted
eventually if there has been any indication for potential SAN changes.
On the other hand, lots of virtual servers receiving the same indication
for a SAN change had better not attempt to conduct a scan instantly,
that is, at the same time.

Hence this patch has a two-fold approach for better port scanning:
the introduction of a rate limit to amend frequency issues, and the
introduction of a short random backoff to amend simultaneity issues.
Both approaches boil down to deferred port scans, with delays
comprising parts for both approaches.

The new port scan behaviour is summarised best by:

                                               NEW:    NEW:
                          no_auto_port_rescan  random  rate    flush
                                               backoff limit   =wait

adapter resume/thaw       yes                  yes     no      yes*
adapter online (user)     no                   yes     no      yes*
port rescan (user)        no                   no      no      yes
adapter recovery (user)   yes                  yes     yes     no
adapter recovery (other)  yes                  yes     yes     no
incoming ELS              yes                  yes     yes     no
incoming ELS lost         yes                  yes     yes     no

Implementation is straight-forward by converting an existing worker to
a delayed worker. But care is needed whenever that worker is going to be
flushed (in order to make sure work has been completed), since a flush
operation cancels the timer set up for deferred execution (see * above).

There is a small race window whenever a port scan work starts
running up to the point in time of storing the time stamp for that port
scan. The impact is negligible. Closing that gap isn't trivial, though, and
would the destroy the beauty of a simple work-to-delayed-work conversion.
Signed-off-by: NMartin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: NSteffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Through sysfs attributes, zfcp unit objects
provide a trigger for manual LUN recovery
and export information for problem determination.

With commit
f8210e34
"[SCSI] zfcp: Allow midlayer to scan for LUNs when running in NPIV mode"
and when attaching SCSI devices through this new optional method,
no more zfcp unit objects are allocated for such SCSI devices.
Hence, the above-mentioned trigger and information were missing.

The information and context is located in SCSI transport device data since
b62a8d9b
"[SCSI] zfcp: Use SCSI device data zfcp_scsi_dev instead of zfcp_unit"
57c23773
"[SCSI] zfcp: Add zfcp private struct as SCSI device driver data"
Hence, introduce the trigger and the information unconditionally
for all SCSI devices attached through zfcp.

We prefix the attribute names with 'zfcp_' to prevent collisions and
to avoid mix-ups such as with the common 'state' attribute.

Since some of the new attribute views do not need zfcp_port
in the ZFCP_DEFINE_SCSI_ATTR helper macro, remove zfcp_port
to avoid compiler warnings on unused variable.
It's easy to open code the conversion from zfcp_scsi_dev to zfcp_port
for the two already existing attributes hba_id and wwpn.
Signed-off-by: NSteffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: NMartin Peschke <mpeschke@linux.vnet.ibm.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch also removes unnecessary printk(KERN_INFO
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Acked-by: NAnil Gurumurthy <anil.gurumurthy@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch removes some leftovers for commit
663e0890
"[SCSI] zfcp: remove access control tables interface".

The "access denied" case for ports is gone, as well.
The corresponding flag was cleared, but never set.
So clean it up.

Sysfs flag is kept, though, for backward-compatibility.
Now it returns always 0.
Signed-off-by: NMartin Peschke <mpeschke@linux.vnet.ibm.com>
Signed-off-by: NSteffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Since virtio_scsi has supported multi virtqueue already,
it is natural to map the virtque to hw-queue of blk-mq.
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

It is already using atomic test_and_set_bit to do the
allocation.

There is some microscopic chance of starvation, but it is
so microscopic that it should never happen in reality.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NWebb Scales <webbnh@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

If the kernel is booted with the reset_device parameter, which
is done for kdump, then the driver needs to call pci_set_master
after pci_enable_device to reenable bus mastering (since
the preceding pci_disable_device call disables bus mastering).

Also, place that after pci_request_regions both in the
kdump code and the normal pci_init code.

Remove the comment summarizing what pci_set_master
does, with the incomplete commentary on the impact of
pci_disable_device.
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

There isn't anything in hpsa that requires the host lock to be held
during queuecommand.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: NStephen M. Cameron <stephenmcameron@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

We were printing a lot of useless information before ultimately
just passing things up to the SCSI mid layer.  Just let the
midlayer handle it without LLD chatter.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NStephen M. Cameron <stephenmcameron@gmail.com>
Reviewed-by: NJoe Handzik <joseph.t.handzik@hp.com>
Reviewed-by: NScott Teel <scott.teel@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Use atomics for commands_outstanding instead of protecting with spin locks.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NStephen M. Cameron <stephenmcameron@gmail.com>
Reviewed-by: NJoe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Using bit fields for hardware command fields isn't portable and
relies on assumptions about how the compiler lays out the bits.
We can fix this in the driver's internal command structure, but the
ioctl interface we can't change because it is part of the
userland ABI.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NWebb Scales <webb.scales@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The hardware needs little endian scatter gather addresses and
lengths but we were not bothering to convert from cpu byte
order as we should have been.  On Intel, this is all just
a bunch of no-ops macros, but it makes the code endian-clean(er).
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Reviewed-by: NWebb Scales <webbnh@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

We were allocating roughly double the amount of memory
we should be due to ReportLUNdata and ExtendedReportLUNdata
containing a non-zero sized array but adding extra memory
to allocate as if the array were zero sized.

Track the logical and physical sizes separately.
Allocate the memory based on the specific data
structure sizes.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NWebb Scales <webb.scales@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

In the case of LUN data changing, the driver will
auto rescan and so it's not even true that "action" is
"required".

Remove "action required" phrases from warning messages and
replace with description phrases.
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Reviewed-by: NStephen M. Cameron <stephenmcameron@gmail.com>
Reviewed-by: NJoe Handzik <joseph.t.handzik@hp.com>
Reviewed-by: NWebb Scales <webb.scales@hp.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>