Avoid duplicating code by moving the calls to spi_nor_write_enable() and
spi_nor_wait_till_ready() inside the Write Status Register methods.

Move spi_nor_write_sr() to avoid forward declaration of
spi_nor_wait_till_ready().
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

spi_nor_clear_sr() and spi_nor_clear_fsr() are called just in case
of errors. The callers didn't check their return value, make them
of type void.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Rename 'sst_write_err' label to 'out' as it is no longer generic for
all the errors in the sst_write() method, and may introduce confusion.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Check for the return vales of each Register Operation.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NVignesh Raghavendra <vigneshr@ti.com>

Spare the callers of printing debug messages by themselves.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NVignesh Raghavendra <vigneshr@ti.com>

What most users care about is "my dev is not working properly".
All low level information should be discovered when activating
the debug traces.

Keep error messages just for the following cases:
- when the SR/FSR report program or erase fails, or attempts of
  modifying a protected sector,
- when the JEDEC ID is not recognized,
- when the resume() call fails,
- when the spi_nor_check() fails.
Suggested-by: NBoris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NVignesh Raghavendra <vigneshr@ti.com>

spi_nor_read_raw() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.

Fixes: f384b352 ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

spi_nor_read() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.

Fixes: 59451e12 ("mtd: spi-nor: change return value of read/write")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Intel Comet Lake-H PCH has the same SPI serial flash controller as Comet
Lake-LP. Add Comet Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Print identifying information about struct device.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Constify the data to write to the Status Register.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

In case the write of the first byte failed, retlen was incorrectly
incremented to *retlen += actual; on the exit path. retlen should be
incremented when actual data was written to the flash.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Drop the error messages from the callers, since the callees
already print an error message in case of failure.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Let the callers pass the pointer to the DMA-able buffer where
the value of the Configuration Register will be written. This way we
avoid the casts between int and u8, which can be confusing.

Callers stop compare the return value of spi_nor_read_cr() with negative,
spi_nor_read_cr() returns 0 on success and -errno otherwise.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Let the callers pass the pointer to the DMA-able buffer where
the value of the Flag Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.

Caller stops compare the return value of spi_nor_read_fsr() with negative,
spi_nor_read_fsr() returns 0 on success and -errno otherwise.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Let the callers pass the pointer to the DMA-able buffer where
the value of the Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.

Callers stop compare the return value of spi_nor_read_sr() with negative,
spi_nor_read_sr() returns 0 on success and -errno otherwise.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Do not overwrite the error numbers received the Register Operations
methods.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

ret is already of type int.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

spi_mem_exec_op()
nor->controller_ops->write_reg()
nor->controller_ops->read_reg()
spi_nor_wait_till_ready()
Return 0 on success, -errno otherwise.

Stop compare with negative and compare with zero in all the register
operations methods.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Group all register methods up in the file, to avoid forward
declarations.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Two new lines, one after another, drop one.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

All the core functions should begin with "spi_nor_".
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

n_tx was never used, drop it. Replace 'const u8 *txbuf' with 'u8 opcode',
to comply with the SPI NOR int (*read_reg)() method. The 'const'
qualifier has no meaning for parameters passed by value, drop it.
Going furher, the opcode was passed to cqspi_calc_rdreg() and never used,
drop it.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Move all SPI NOR controller driver specific ops in a dedicated
structure. 'struct spi_nor' becomes lighter.

Use size_t for lengths in 'int (*write_reg)()' and 'int (*read_reg)()'.
Rename wite/read_buf to buf, the name of the functions are
suggestive enough. Constify buf in int (*write_reg). Comply with these
changes in the SPI NOR controller drivers.
Suggested-by: NBoris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

The pointer to 'struct spi_nor' is kzalloc'ed above in the code.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>

Tested on HiWiFi C526A

Datasheet is available at:
http://www.xinyahong.com/upLoad/product/month_1411/201411201256018276.pdfSigned-off-by: NDENG Qingfang <dqfext@gmail.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Now that SPI flash controllers without a software sequencer are
supported, it's trivial to add support for CNL and its PCI ID.

Values from https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/300-series-chipset-pch-datasheet-vol-2.pdfSigned-off-by: NJethro Beekman <jethro@fortanix.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Some flash controllers don't have a software sequencer. Avoid
configuring the register addresses for it, and double check
everywhere that its not accidentally trying to be used.

Every use of `sregs` is now guarded by a check of `sregs` or
`swseq_reg`. The check might be done in the calling function.
Signed-off-by: NJethro Beekman <jethro@fortanix.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Commit 7e534323 ("mtd: rawnand: Pass a nand_chip object to
chip->read_xxx() hooks") modified the prototype of the struct nand_chip
read_buf function pointer. In the au1550nd driver we have 2
implementations of read_buf. The previously mentioned commit modified
the au_read_buf() implementation to match the function pointer, but not
au_read_buf16(). This results in a compiler warning for MIPS
db1xxx_defconfig builds:

  drivers/mtd/nand/raw/au1550nd.c:443:57:
    warning: pointer type mismatch in conditional expression

Fix this by updating the prototype of au_read_buf16() to take a struct
nand_chip pointer as its first argument, as is expected after commit
7e534323 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx()
hooks").

Note that this shouldn't have caused any functional issues at runtime,
since the offset of the struct mtd_info within struct nand_chip is 0
making mtd_to_nand() effectively a type-cast.
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Fixes: 7e534323 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx() hooks")
Cc: stable@vger.kernel.org # v4.20+
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

write_sr() sends data to the SPI memory, fix the direction.

Fixes: b35b9a10 ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Reported-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: NJohn Garry <john.garry@huawei.com>
Acked-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/mtd/devices/pmc551.c: In function pmc551_erase:
drivers/mtd/devices/pmc551.c:142:15: warning: variable soff_lo set but not used [-Wunused-but-set-variable]
drivers/mtd/devices/pmc551.c: In function pmc551_read:
drivers/mtd/devices/pmc551.c:232:15: warning: variable soff_lo set but not used [-Wunused-but-set-variable]
drivers/mtd/devices/pmc551.c: In function pmc551_write:
drivers/mtd/devices/pmc551.c:289:15: warning: variable soff_lo set but not used [-Wunused-but-set-variable]

It is not used since commit cdf0a7d1 ("[MTD]
pmc551 whitespace cleanup")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: Nzhengbin <zhengbin13@huawei.com>
Signed-off-by: NRichard Weinberger <richard@nod.at>

The chip state is set to erasing by the function after getting chip.
So it should be to get chip as erasing mode at first.
But previously it was to get chip as writing mode then fix as erasing.
Signed-off-by: NTokunori Ikegami <ikegami.t@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: NRichard Weinberger <richard@nod.at>

In sm_init_zone(), 'zone->lba_to_phys_table' is allocated through
kmalloc_array() and 'zone->free_sectors' is allocated in kfifo_alloc()
respectively. However, they are not deallocated in the following execution
if sm_read_sector() fails, leading to memory leaks. To fix this issue, free
them before returning -EIO.
Signed-off-by: NWenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: NRichard Weinberger <richard@nod.at>

This moves the CMDLINE partition parser down into the
parser subdirectory. No functional change.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRichard Weinberger <richard@nod.at>

This moves the OF/device tree partition parser down into the
parser subdirectory. No functional change.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRichard Weinberger <richard@nod.at>

This moves the BCM63xx partition parser down into the
parser subdirectory. No functional change.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRichard Weinberger <richard@nod.at>

This moves the BCM47xx partition parser down into the
parser subdirectory. No functional change.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRichard Weinberger <richard@nod.at>

This moves the TI AR7 partition parser down into the
parser subdirectory. No functional change.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRichard Weinberger <richard@nod.at>

We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NRichard Weinberger <richard@nod.at>

The phram code implements managing multiple devices through a linked
list.
However, due to the module parameter permission of 0, the
/sys/module/phram/parameters/phram interface is missing.
The command line arguments in insmod can only create one device.

Therefore, add writable permissions to the module parameters, create
/sys/module/phram/parameters/phram interface, and create multi-device
support.
Signed-off-by: NXiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: NRichard Weinberger <richard@nod.at>