There are currently 2 differents naming conventions used between the
existing Armada SoC DT files for pinctrl entries (*_pin(s): *-pin(s)
and pmx_*: pmx-*) with a vast majority of files using the former:

$ grep _pin arch/arm/boot/dts/armada-*.dts* | wc -l
155
$ grep pmx arch/arm/boot/dts/armada-*.dts* | wc -l
13

In fact, only some Armada XP files are using the second variant.
This patch normalizes those files (mainly ge0/1 entries) to use
the first variant.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/00114c3169e1d93259ff4150ed46ee36eae16b1e.1416670812.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

While renaming pinctrl entries during reviews of Synology DS414 support
series, I missed three entries, as reported by Ben. This patch fixes
those.
Reported-by: NBen Peddell <klightspeed@killerwolves.net>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/608e4fd6e06e9c5289a84b9c38e81b2456dbcd79.1416670812.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Synology DS414 is a 4-bay NAS powered by a Marvell Armada XP
(mv78230 dual-core @1.33Ghz). It is very similar on many aspects
to previous 4-bay synology models based on Marvell kirkwood SoC.
Here is a short summary of the device:

 - 1GB RAM
 - Boot on SPI flash (64Mbit Micron N25Q064)
 - 2 GbE interfaces (Armada MAC connected to two Marvell 88E1512
   PHY via RGMII)
 - 1 front USB 2.0 ports (directly handled by the Armada 370)
 - 2 rear USB 3.0 ports (handled by an EtronTech EJ168A XHCI
   controller on the PCIe bus)
 - 4 internal SATA ports handled by a Marvell 88SX7042 SATA-II
   controller on the PCIe bus)
 - Seiko S-35390A I2C RTC chip
 - UART0 providing serial console
 - UART1 used for poweroff (connected to a Microchip PIC16F883)

Additional note: the front LEDs the and the two fans are not directly
connected to the SoC and under its control. The former are presumably
driven by the SATA controller, the latter by the PIC.

[ jac: fixed up s/ge[01]_rgmii_pins/pmx_ge[01]_rgmii/ to match
armada-xp.dtsi ]
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/5b678d6d1f2f42f4bf0d087878b9d8024d463ea7.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Synology DS213j is a 2-bay NAS powered by a Marvell Armada 370
(88F6710 @1.2Ghz). It is very similar on many aspects to previous
2-bay synology models based on Marvell kirkwood SoC. Here is a
short summary of the device:

 - 512MB RAM
 - boot on SPI flash (64Mbit Micron N25Q064)
 - 1 GbE interface (Armada MAC connected to a Marvell 88E1512
   PHY via SGMII)
 - 2 rear USB 2.0 ports (directly handled by the Armada 370)
 - 2 internal SATA ports handled by the Armada 370: 2 GPIO for
   presence, 2 for powering them
 - two front amber LED (disk1, disk2) controlled by the SoC
 - Seiko S-35390A I2C RTC chip
 - UART0 providing serial console
 - UART1 used for poweroff (connected to a TI MSP430F2111)
 - Fan handled via 4 GPIO (3 for speed, 1 for alarm)
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/20f1a03897df1d825b62abdd525e588a8e39b3ec.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This patch defines common Armada XP pinctrl settings in armada-xp.dtsi
for the supported SPI interface (MPP36-39) and use it as default
for Armada XP spi interface. That being done, it removes the now
redundant definitions in armada-xp-axpwifiap.dts.

Note: this patch has the potential to break out-of-tree users w/o
specific pinctrl settings for their spi interfaces if the default
above does not match their config (i.e. if they do not use CS0).
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/d404b7abd80ee5a0fd8e8d3586d33cd37740d589.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This patch defines common Armada XP pinctrl settings for uart2 and
uart3 interfaces (uart0 and uart1 rx/tx do not rely on MPP):

 uart2: MPP42-43 as default
 uart3: MPP44-45 as default
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/fd51c080c7139a67ec01df8d797f1e88ce557796.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This patch defines common Armada 370 pinctrl settings for uart0 and
uart1 interfaces:

 uart0: MPP0-1 as default
 uart1: MPP41-42 as default

Note: this patch has the potential to break out-of-tree users w/o
specific pinctrl settings for their uart interfaces if the default
above does not match their config.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/31412e57955c98bc9cc47b70726b5072af945cc3.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This patch defines common Armada 370 pinctrl settings for spi0 and spi1
interfaces:

 spi0: MPP33-36 as default, MPP32,63-65 as available alternate config
 spi1: MPP49-52 as default

Currently, the Armada 370 DB .dts file has no explicit pinctrl info
for the spi0 interface used to access the flash on the board. The
patch fixes that by also adding explicit pinctrl info (MPP32,63-65)
for this SPI interface.

Note: this patch has the potential to break out-of-tree users w/o
specific pinctrl settings for their spi interfaces if the default
above does not match their config.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/1e812eb63b37718e273463e22e4d7512f8f0b624.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

What was done by Sebastian in 264a05e1 ("ARM: mvebu: armada-xp:
Add node alias to pinctrl and add base address") and 01c43422
("ARM: mvebu: armada-xp: Use pinctrl node alias") can also be done for
Armada 370, i.e.

 - Rename Armada 370 pinctrl node to pin-ctrl with its address encoded
 - Add a node alias to access the pinctrl node easily.
 - use the newly available alias in existing Armada 370 .dts files

We can even go a bit further by putting the pinctrl node definition in
armada-370-xp.dtsi, with only its reg property defined. This allows us
to then also use the newly defined node alias in armada-xp.dtsi,
armada-370.dtsi.
Suggested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/b54eb45e5242728aace3ce8aef2eae4251f8dea3.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Now that labels for uartX are available in Marvell Armada .dtsi files,
this patch replaces the "/soc/internal-regs/serial@12000" found in
armada-xp-lenovo-ix4-300d.dts file for stdout-path property by the more
concise &uart0.
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/d1a883510e01f7f212a385e826dccbef903fae42.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds uartX labels for Armada SoC serial nodes. This is
a preliminary work to be able to easily reference the serial lines
in Device Tree files. One expected use is when providing stdout-path
property for barebox.
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/0683d1a823fe9b75849f3dafcf1cf6ee291cdca6.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

As reported by Andrew, the vendor prefix for Seiko Instruments, Inc.
S-35390A I2C RTC chip in kirkwood-synology.dtsi has a typo (ssi
instead of sii). This patches fixes it.

Note: i2c devices ignore the optional vendor prefix, which explains
why it worked with the typo and also why there is no backward
compatibility issues with the fix.
Reported-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/0444140a267d982c3e5f5f2b7b5f2dc41d010e2a.1416613429.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Commit a095b1c7 ("ARM: mvebu: sort DT nodes by address")
missed placing the system-controller in the correct order.

Fixes: a095b1c7 ("ARM: mvebu: sort DT nodes by address")
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/20141114204333.GS27002@pengutronix.deSigned-off-by: NJason Cooper <jason@lakedaemon.net>

In order to update MAC address entries in the ethernet nodes in Device Tree
both mainline U-Boot and Barebox bootloaders accept the same format of aliases,
which is 'ethernetX', where X stands for an interface number.
Other platforms in the mainline Linux, that comprise ethernet references in
'/aliases' node (like various flavours of imx or sunXi), follow the naming
scheme described above.

This commit ajusts ethernet aliases of Marvell Armada 38x SoC to be properly
recognized by bootloaders' MAC address fixup routines.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-5-git-send-email-mw@semihalf.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

For proper operation of Armada 38x SDHCI controller proper 'clocks' property
is sufficient. Therefore it is not useful to keep an additional
'clock-frequency' property in SDHCI controller node of board-level Device Tree
file for Armada 385 DB.

This commit gets rid of useless 'clock-frequency' property.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-4-git-send-email-mw@semihalf.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

The Marvell Armada 38x SoC's SDHCI interface is capable of using 1.8v voltage,
needed for driving "UHS-I" SD cards at their full speed. It is not, however,
possible on the DB board. Due to physical connectivity connector supply is tied
to 3v and any attempt of changing voltage in order to operate in the fastest UHS
modes fails.

This patch enables equivalent SDHCI quirk in order to adjust controller
operation to system capabilities.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-3-git-send-email-mw@semihalf.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

The 370 rd has a 7 port, mv88E6182 switch, connected to eth1.  Add a
fixed-link subnode to the ethernet device tree node, to force
gigabit/full duplex.  Add a dsa node, with describing the four used
ports. This requires adding an alias to the mdio node, so it can be
referenced as a phandle.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415214121-29286-3-git-send-email-andrew@lunn.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This commit modifies the Armada 370 and Armada 370 DB Device Tree
descriptions to use the simple-card DT binding to describe the audio
complex of the Armada 370 DB instead of a custom audio machine driver.

To do so, it:

 - Adds the sound-dai-cells properties to the CS42L51 node, the audio
   controller node and the SPDIF in/out nodes.

 - Completely changes the description of the sound complex to use the
   "simple-audio-card" DT binding instead of the
   "marvell,a370db-audio" DT binding.

 - Fixes the indentation to properly use tabs instead of spaces.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-6-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Back when audio was enabled, the muxing of some MPP pins was causing
problems. However, since commit fea038ed ("ARM: mvebu: Add proper
pin muxing on the Armada 370 DB board"), those problematic MPP pins
have been assigned a proper muxing for the Ethernet interfaces. This
proper muxing is now conflicting with the hog pins muxing that had
been added as part of 249f3822 ("ARM: mvebu: add audio support to
Armada 370 DB").

Therefore, this commit simply removes the hog pins muxing, which
solves a warning a boot time due to the conflicting muxing
requirements.

Fixes: fea038ed ("ARM: mvebu: Add proper pin muxing on the Armada 370 DB board")
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-5-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

There is only one 74hc595 connected to GPIO but two were given
in the registers-number property. Fix it up.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: NBenoit Masson <yahoo@perenite.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

There is an I2C eeprom connected on Lenovo ix4-300d, add the
corresponding node.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: NBenoit Masson <yahoo@perenite.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Lenovo ix4-300d has two ethernet PHYs connected via RGMII. Add the
corresponding pinctrl settings.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: NBenoit Masson <yahoo@perenite.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

There is a GMII setting for GE0, add it to the common pinctrl node.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: NBenoit Masson <yahoo@perenite.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Pinctrl settings for GE0 and GE1 are not only usable on RD-AXPWiFiAP.
Moreover, naming the RGMII settings pmx-ge{0,1} is not precise enough
as there is also a GMII setting for GE0.

Move the pinctrl sub-nodes to the common pinctrl node and rename them
to pmx-ge{0,1}-rgmii.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: NBenoit Masson <yahoo@perenite.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Armada XP pinctrl node gained an alias, make use of it.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-By: NBenoit Masson <yahoo@perenite.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

In other MVEBU SoCs, the pin controller node is called pin-ctrl with
its base address added. Also, we have a node alias to access the pinctrl
node easily. Fix this for Armada XP pinctrl nodes to be consistent with
other SoCs.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-By: NBenoit Masson <yahoo@perenite.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

All current Armada XP SoCs have their pin controller at 0x18000/0x38.
Move the common properties of pinctrl nodes to armada-xp.dtsi to allow
to share pinctrl settings later.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-By: NBenoit Masson <yahoo@perenite.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The DIR665 has an 8 port Ethernet Switch, a Marvell mv88e6171. Add a
DSA node in DT, to instantiate DSA support for the 4 back panel ports,
the Internet port, and the port to the CPU which is connected to eth0.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414793613-11798-3-git-send-email-andrew@lunn.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Add a device tree description of the DLINK DIR665 wireless access
point. The support for the 88E6171 switch will be added in a later
patch.
Signed-off-by: NClaudio Leite <leitec@staticky.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414793613-11798-2-git-send-email-andrew@lunn.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>

NETGEAR ReadyNAS 2120 supports its four main SATA disks via 2
Marvell 88SE9170 SATA controllers connected on the PCIe bus
of the the SoC. The two eSATA ports available at the rear of
the device are handled by the native SATA controller of the
Armada XP SoC powering the NAS. This patch enables the SoC
SATA controller in the .dts file to make those two rear ports
available.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/f3876c7a9ef11eb758b9df18c671ee740b8be614.1414250947.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Now that the timer and watchdog drivers support the Armada 375 usage of
the reference clock, we can enable it in the devicetree.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1414248522-16055-5-git-send-email-ezequiel.garcia@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

On NETGEAR ReadyNAS 102, the two disks are connected to the external
Marvell 88SE9170 SATA Controller connected to the PCIe bus. The rear
eSATA port is connected to the native Armada 370 SATA controller.

This patch updates the comments in .dts file wrt SATA interfaces and
reduces the number of ports for native Armada 370 interface from 2
to 1.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/4af680f9a68281755e31df2491f0590046138230.1414185031.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

When writing initial .dts file for NETGEAR ReadyNAS 102, I put the wrong color
for backup and SATA leds (green instead of blue for all three).
Reported-by: NJohan Kristell <johan.kristell@gmail.com>
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/4eb4049d934a3a8fe9f7235dafb6842422792566.1414185031.git.arno@natisbad.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

The L2 cache controller on the Armada 370 and Armada XP SoCs is a
unified cache. Moreover, the Aurora cache controller is compatible
with the L2x0 cache controller: the "cache-unified" property is
required by its binding.

This patch fixes the Aurora L2 cache node for the Armada 370 and
Armada XP SoCs by adding this property.
Reported-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1412588276-4514-1-git-send-email-gregory.clement@free-electrons.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Explicitly set the dr_mode for the second dwc3 controller on the
Arndale Octa board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is build
with USB gadget support.
Reported-By: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

In case the optional dr_mode property isn't set in the dwc3 nodes the
the controller will go into OTG mode if both USB host and USB gadget
functionality are enabled in the kernel configuration. Unfortunately
this results in USB not working on exynos5420-peach-pit and
exynos5800-peach-pi with such a kernel configuration unless manually
change the mode. To resolve that explicitly configure the dual role
mode as host.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

CM-QS600 is a APQ8064 based computer on module.
The details are available at
http://compulab.co.il/products/computer-on-modules/cm-qs600/Signed-off-by: NMike Rapoport <mike.rapoport@gmail.com>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.
Signed-off-by: NTim Bird <tim.bird@sonymobile.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add SATA PHY and SATA AHCI controller nodes to device tree to enable
generic ahci support on the IPQ8064/AP148 board.
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Fix wrong compatible string of Exynos3250 RTC (Real-Time Clock) dt node.
The RTC of Exynos3250 must need additional source clock (XrtcXTI).
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>