Add a new spi_master.flags word listing constraints relevant to that
controller.  Define the first constraint bit: a half duplex restriction.
Include that constraint in the OMAP1 MicroWire controller driver.

Have the mmc_spi host be the first customer of this flag.  Its coding
relies heavily on full duplex transfers, so it must fail when the
underlying controller driver won't perform them.

(The spi_write_then_read routine could use it too: use the
temporarily-withdrawn full-duplex speedup unless this flag is set, in
which case the existing code applies.  Similarly, any spi_master
implementing only SPI_3WIRE should set the flag.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:

 * SPI_NO_CS ... a second 3-wire variant, where the chipselect
   line is removed instead of a data line; transfers are still
   full duplex.

   This obviously has STRONG protocol implications since the
   chipselect transitions can't be used to synchronize state
   transitions with the SPI master.

 * SPI_READY ... defines open drain signal that's pulled low
   to pause the clock.  This defines a 5-wire variant (normal
   4-wire SPI plus READY) and two 4-wire variants (READY plus
   each of the 3-wire flavors).

   Such hardware flow control can be a big win.  There are ADC
   converters and flash chips that expose READY signals, but not
   many host controllers support it today.

The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack.  That's a mode most hardware can easily support
(unlike SPI_READY).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: "Paulraj, Sandeep" <s-paulraj@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With ELF, at generating coredump, some more headers other than used
vmas are added.

When max_map_count == 65536, a core generated by following kinds of
code can be unreadable because the number of ELF's program header is
written in 16bit in Ehdr (please see elf.h) and the number overflows.

==
	... = mmap(); (munmap, mprotect, etc...)
	if (failed)
		abort();
==

This can happen in mmap/munmap/mprotect/etc...which calls split_vma().

I think 65536 is not safe as _default_ and reduce it to 65530 is good
for avoiding unexpected corrupted core.

Anyway, max_map_count can be enlarged by sysctl if a user is brave..
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Jakub Jelinek <jakub@redhat.com>
Acked-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the PCI-Express NetMos 9901 Multi-IO card.

0001:06:00.0 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
        Subsystem: Device [a000:1000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 65
        Region 0: I/O ports at 0030 [size=8]
        Region 1: Memory at 80105000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80104000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: serial
        Kernel modules: 8250_pci

0001:06:00.1 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
        Subsystem: Device [a000:1000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 65
        Region 0: I/O ports at 0020 [size=8]
        Region 1: Memory at 80103000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80102000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: serial
        Kernel modules: 8250_pci

0001:06:00.2 Parallel controller [0701]: NetMos Technology Device [9710:9901] (prog-if 03 [IEEE1284])
        Subsystem: Device [a000:2000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 65
        Region 0: I/O ports at 0010 [size=8]
        Region 1: I/O ports at <unassigned>
        Region 2: Memory at 80101000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80100000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: parport_pc
        Kernel modules: parport_pc

[   16.760181] PCI parallel port detected: 416c:0100, I/O at 0x812010(0x0), IRQ 65
[   16.760225] parport0: PC-style at 0x812010, irq 65 [PCSPP,TRISTATE,EPP]
[   16.851842] serial 0001:06:00.0: enabling device (0004 -> 0007)
[   16.883776] 0001:06:00.0: ttyS0 at I/O 0x812030 (irq = 65) is a ST16650V2
[   16.893832] serial 0001:06:00.1: enabling device (0004 -> 0007)
[   16.926537] 0001:06:00.1: ttyS1 at I/O 0x812020 (irq = 65) is a ST16650V2
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

alpha percpu access requires custom SHIFT_PERCPU_PTR() definition for
modules to work around addressing range limitation.  This is done via
generating inline assembly using C preprocessing which forces the
assembler to generate external reference.  This happens behind the
compiler's back and makes the compiler think that static percpu variables
in modules are unused.

This used to be worked around by using __unused attribute for percpu
variables which prevent the compiler from omitting the variable; however,
recent declare/definition attribute unification change broke this as
__used can't be used for declaration.  Also, in the process,
PER_CPU_ATTRIBUTES definition in alpha percpu.h got broken.

This patch adds PER_CPU_DEF_ATTRIBUTES which is only used for definitions
and make alpha use it to add __used for percpu variables in modules.  This
also fixes the PER_CPU_ATTRIBUTES double definition bug.
Signed-off-by: NTejun Heo <tj@kernel.org>
Tested-by: Nmaximilian attems <max@stro.at>
Acked-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change the eventfd interface to de-couple the eventfd memory context, from
the file pointer instance.

Without such change, there is no clean way to racely free handle the
POLLHUP event sent when the last instance of the file* goes away.  Also,
now the internal eventfd APIs are using the eventfd context instead of the
file*.

This patch is required by KVM's IRQfd code, which is still under
development.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: Gregory Haskins <ghaskins@novell.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit 2f0d0fd2 ("ide-acpi: cleanup
do_drive_get_GTF()") didn't account for the lack of hwif->acpidata
check in generic_ide_suspend() [ indirect user of do_drive_get_GTF()
through ide_acpi_exec_tfs() ] resulting in broken resume when ACPI
support is enabled but ACPI data is unavailable.

Fix it by adding ide_port_acpi() helper for checking if port needs
ACPI handling and cleaning generic_ide_{suspend,resume}() to use it
instead of hiding hwif->acpidata and ide_noacpi checks in IDE ACPI
helpers (this should help in preventing similar bugs in the future).

While at it:
- kill superfluous debugging printks in ide_acpi_{get,push}_timing()
Reported-and-tested-by: NEtienne Basset <etienne.basset@numericable.fr>
Also-reported-and-tested-by: NJeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new fsnotify infrastructure (starting at 90586523) causes an oops in
spufs, where we populate a directory with files before instantiating the
directory itself. The new changes seem to have introduced an assumption
that a dentry's parent will be positive when instantiating.

This change makes it once again possible to d_instantiate a dentry
with a negative parent, and brings __fsnotify_d_instantiate() into
line with inotify_d_instantiate(), which already has this NULL check.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NEric Paris <eparis@redhat.com>

This patch fixes an imbalance message as reported by J.R. Okajima.
The IMA file counters are incremented in ima_path_check. If the
actual open fails, such as ETXTBSY, decrement the counters to
prevent unnecessary imbalance messages.
Reported-by: NJ.R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: NMimi Zohar <zohar@us.ibm.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

make_all_cpus_request contains a race condition which can
trigger false request completed status, as follows:

CPU0                                              CPU1

if (test_and_set_bit(req,&vcpu->requests))
   ....                                        	   if (test_and_set_bit(req,&vcpu->requests))
   ..                                                  return
proceed to smp_call_function_many(wait=1)

Use a spinlock to serialize concurrent CPUs.

Cc: stable@kernel.org
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_kill_rq()
  and ide_floppy_do_request() for failed requests.
  [ bugfix part ]

* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_do_devset()
  and ide_complete_drive_reset().  Then remove ide_rq_bytes().
  [ cleanup part ]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces a new sysctl:

    /proc/sys/kernel/panic_on_io_nmi

which defaults to 0 (off).

When enabled, the kernel panics when the kernel receives an NMI
caused by an IO error.

The IO error triggered NMI indicates a serious system
condition, which could result in IO data corruption. Rather
than contiuing, panicing and dumping might be a better choice,
so one can figure out what's causing the IO error.

This could be especially important to companies running IO
intensive applications where corruption must be avoided, e.g. a
bank's databases.

[ SuSE has been shipping it for a while, it was done at the
  request of a large database vendor, for their users. ]
Signed-off-by: NKurt Garloff <garloff@suse.de>
Signed-off-by: NRoberto Angelino <robertangelino@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <20090624213211.GA11291@kroah.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Currently the 4th parameter of get_user_pages() is called len, but its
in pages, not bytes. Rename the thing to nr_pages to avoid future
confusion.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

helpers: get_cached_acl(inode, type), set_cached_acl(inode, type, acl),
forget_cached_acl(inode, type).

ubifs/xattr.c needed includes reordered, the rest is a plain switchover.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

No helpers, no conversions yet.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This patch adds ioctls to vfs for compatibility with legacy XFS
pre-allocation ioctls (XFS_IOC_*RESVP*). The implementation
effectively invokes sys_fallocate for the new ioctls.
Also handles the compat_ioctl case.
Note: These legacy ioctls are also implemented by OCFS2.

[AV: folded fixes from hch]
Signed-off-by: NAnkit Jain <me@ankitjain.org>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

When the kernel is configured with CONFIG_TIMER_STATS but timer
stats are runtime disabled we still get calls to
__timer_stats_timer_set_start_info which initializes some
fields in the corresponding struct timer_list.

So add some quick checks in the the timer stats setup functions
to avoid function calls to __timer_stats_timer_set_start_info
when timer stats are disabled.

In an artificial workload that does nothing but playing ping
pong with a single tcp packet via loopback this decreases cpu
consumption by 1 - 1.5%.

This is part of a modified function trace output on SLES11:

 perl-2497  [00] 28630647177732388 [+  125]: sk_reset_timer <-tcp_v4_rcv
 perl-2497  [00] 28630647177732513 [+  125]: mod_timer <-sk_reset_timer
 perl-2497  [00] 28630647177732638 [+  125]: __timer_stats_timer_set_start_info <-mod_timer
 perl-2497  [00] 28630647177732763 [+  125]: __mod_timer <-mod_timer
 perl-2497  [00] 28630647177732888 [+  125]: __timer_stats_timer_set_start_info <-__mod_timer
 perl-2497  [00] 28630647177733013 [+   93]: lock_timer_base <-__mod_timer
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mustafa Mesanovic <mustafa.mesanovic@de.ibm.com>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20090623153811.GA4641@osiris.boeblingen.de.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

There are some broken devices that report multiple DMA xfer modes
enabled at once (ATA spec doesn't allow it) but otherwise work fine
with DMA so just delete ide_id_dma_bug().

[ As discovered by detective work by Frans and Bart, due to how
  handling of the ID block was handled before commit c4199930
  ("ide-iops: only clear DMA words on setting DMA mode") this
  check was always seeing zeros in the fields or other similar
  garbage.  Therefore this check wasn't actually checking anything.
  Now that the tests actually check the real bits, all we see are
  devices that trigger the check yet work perfectly fine, therefore
  killing this useless check is the best thing to do. -DaveM ]
Reported-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A number of places in the audit system we send an op= followed by a string
that includes spaces.  Somehow this works but it's just wrong.  This patch
moves all of those that I could find to be quoted.

Example:

Change From: type=CONFIG_CHANGE msg=audit(1244666690.117:31): auid=0 ses=1
subj=unconfined_u:unconfined_r:auditctl_t:s0-s0:c0.c1023 op=remove rule
key="number2" list=4 res=0

Change To: type=CONFIG_CHANGE msg=audit(1244666690.117:31): auid=0 ses=1
subj=unconfined_u:unconfined_r:auditctl_t:s0-s0:c0.c1023 op="remove rule"
key="number2" list=4 res=0
Signed-off-by: NEric Paris <eparis@redhat.com>

To support domain-isolation usages, the platform hardware must be
capable of uniquely identifying the requestor (source-id) for each
interrupt message. Without source-id checking for interrupt remapping
, a rouge guest/VM with assigned devices can launch interrupt attacks
to bring down anothe guest/VM or the VMM itself.

This patch adds source-id checking for interrupt remapping, and then
really isolates interrupts for guests/VMs with assigned devices.

Because PCI subsystem is not initialized yet when set up IOAPIC
entries, use read_pci_config_byte to access PCI config space directly.
Signed-off-by: NWeidong Han <weidong.han@intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

After the recent changes that went into mm/vmscan.c to overhaul stuff, we
ended up with these warnings on no-mmu systems:

  mm/vmscan.c: In function `shrink_page_list':
  mm/vmscan.c:580: warning: unused variable `vm_flags'
  mm/vmscan.c: In function `shrink_active_list':
  mm/vmscan.c:1294: warning: `vm_flags' may be used uninitialized in this function
  mm/vmscan.c:1242: note: `vm_flags' was declared here

This is because the no-mmu function defines page_referenced() to work on
the first argument only (the page).  It does not clear the vm_flags given
to it because for no-mmu systems, they never actually get utilized.  Since
that is no longer strictly true, we need to set vm_flags to 0 like
everyone else so gcc can do proper dead code elimination without annoying
us with unused warnings.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: NDavid McCullough <davidm@snapgear.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If a kthread happens to use get_user_pages() on an mm (as KSM does),
there's a chance that it will end up trying to read in a swap page, then
oops in grab_swap_token() because the kthread has no mm: GUP passes down
the right mm, so grab_swap_token() ought to be using it.

We have not identified a stronger case than KSM's daemon (not yet in
mainline), but the issue must have come up before, since RHEL has included
a fix for this for years (though a different fix, they just back out of
grab_swap_token if current->mm is unset: which is what we first proposed,
but using the right mm here seems more correct).
Reported-by: NIzik Eidus <ieidus@redhat.com>
Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org>
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Futher document blink_set function pointer
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

There already is a "default-on" trigger but there are problems with it.

For one, it's a inefficient way to do it and requires led trigger support
to be compiled in.

But the real reason is that is produces a glitch on the LED.  The GPIO is
allocate with the LED *off*, then *later* when the trigger runs it is
turned back on.  If the LED was already on via the GPIO's reset default or
action of the firmware, this produces a glitch where the LED goes from on
to off to on.  While normally this is fast enough that it wouldn't be
noticeable to a human observer, there are still serious problems.

One is that there may be something else on the GPIO line, like a hardware
alarm or watchdog, that is fast enough to notice the glitch.

Another is that the kernel may panic before the LED is turned back on, thus
hanging with the LED in the wrong state.  This is not just speculation, but
actually happened to me with an embedded system that has an LED which
should turn off when the kernel finishes booting, which was left in the
incorrect state due to a bug in the OF LED binding code.

We also let GPIO LEDs get their initial value from whatever the current
state of the GPIO line is.  On some systems the LEDs are put into some
state by the firmware or hardware before Linux boots, and it is desired to
have them keep this state which is otherwise unknown to Linux.

This requires that the underlying GPIO driver support reading the value of
output GPIOs.  Some drivers support this and some do not.

The platform device binding gains a field in the platform data
"default_state" that controls this.  There are three constants defined to
select from on, off, or keeping the current state.  The OpenFirmware
binding uses a property named "default-state" that can be set to "on",
"off", or "keep".  The default if the property isn't present is off.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

LEDs driver for National Semiconductor LP3944 Funlight Chip
http://www.national.com/pf/LP/LP3944.html

This helper chip can drive up to 8 leds, with two programmable DIM
modes; it could even be used as a gpio expander but this driver assumes
it is used as a led controller.

The DIM modes are used to set _blink_ patterns for leds, the pattern is
specified supplying two parameters:
  - period: from 0s to 1.6s
  - duty cycle: percentage of the period the led is on, from 0 to 100

LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
leds, the camera flash light and the displays backlights.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The documentation for the parameters of blink_set() was a bit hard
to find so put some where I'd expected to find it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

handle_mm_fault() is now passing fault flags rather than write_access
down to hugetlb_fault(), so better recognize that in hugetlb_fault(),
and in hugetlb_no_page().
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change all the code that deals directly with ICMPv6 type and code
values to use u8 instead of a signed int as that's the actual data
type.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gspca_ov519: add support for the ov511 bridge
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds autobrightness (so that it can
be turned off to make the already present brightness
control work) and light frequency filtering controls.

The lightfreq control needed 2 different entries
in the ctrls array, as the number of options differs
depending on the sensor. Always one of the 2 entires is
disabled ofcourse.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The purpose of this patch is to improve the remote mount path lookup
support for distributed filesystems such as the NFSv4 client.

When given a mount command of the form "mount server:/foo/bar /mnt", the
NFSv4 client is required to look up the filehandle for "server:/", and
then look up each component of the remote mount path "foo/bar" in order
to find the directory that is actually going to be mounted on /mnt.
Following that remote mount path may involve following symlinks,
crossing server-side mount points and even following referrals to
filesystem volumes on other servers.

Since the standard VFS path lookup code already supports walking paths
that contain all these features (using in-kernel automounts for
following referrals) we would like to be able to reuse that rather than
duplicate the full path traversal functionality in the NFSv4 client code.

This patch therefore defines a VFS helper function create_mnt_ns(), that
sets up a temporary filesystem namespace and attaches a root filesystem to
it. It exports the create_mnt_ns() and put_mnt_ns() function for use by
filesystem modules.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In order to allow modules to use it without having to export vfsmount_lock.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SLAB uses get/put_online_cpus() which use a mutex which is itself only
initialized when cpu_hotplug_init() is called.  Currently we hang suring
boot in SLAB due to doing that too late.

Reported by James Bottomley and Sachin Sant (and possibly others).
Debugged by Benjamin Herrenschmidt.

This just removes the dynamic initialization of the data structures, and
replaces it with a static one, avoiding this dependency entirely, and
removing one unnecessary special initcall.
Tested-by: NSachin Sant <sachinp@in.ibm.com>
Tested-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some filesystems need to set lockdep map for i_mutex differently for
different directories. For example OCFS2 has system directories (for
orphan inode tracking and for gathering all system files like journal
or quota files into a single place) which have different locking
locking rules than standard directories. For a filesystem setting
lockdep map is naturaly done when the inode is read but we have to
modify unlock_new_inode() not to overwrite the lockdep map the filesystem
has set.

Acked-by: peterz@infradead.org
CC: mingo@redhat.com
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NJoel Becker <joel.becker@oracle.com>