Now that the config option is gone, the driver needs to be converted
over to using the dynamic_debug infrastructure, like all other USB
drivers have been already.

Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>

The config option is gone, so port the driver over to using the dynamic
debug infrastructure instead, like all other USB drivers.

Cc: Jarod Wilson <jarod@wilsonet.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Cc: Matina Maria Trompouki <mtrompou@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It wasn't even being used for anything, so remove the test for the
config option (as the config option isn't present anymore), and remove
the unused module parameter "debug" so as to not confuse anyone.

Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: "Antti Seppälä" <a.seppala@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the dev_dbg dynamic infrastructure instead of rolling our own custom
debug logic.  This is needed as CONFIG_USB_DEBUG is now gone.

Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Sean Young <sean@mess.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jonathan McCrohan <jmccrohan@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The rr3_ftr function duplicates the in-kernel tracing logic, so remove
it.

This is step 1 of of removing the CONFIG_USB_DEBUG depandancy in this
driver.

Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Sean Young <sean@mess.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jonathan McCrohan <jmccrohan@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A set of new VID/PIDs retrieved from the out-of-tree GobiNet/GobiSerial
Sierra Wireless drivers.
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Link: http://marc.info/?l=linux-usb&m=140136310027293&w=2
Cc: <stable@vger.kernel.org>	# backport in link above
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

module_spi_driver simplifies the code by eliminating
boilerplate code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NDavid Mosberger <davidm@egauge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NDavidm Mosberger <davidm@egauge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

kmalloc the SPI rx and tx data buffers.  This appears to be the only
portable way to guarantee that the buffers are DMA-safe (e.g., in
separate DMA cache-lines).  This patch makes the spi_rdX()/spi_wrX()
non-reentrant, but that's OK because calls to them are guaranteed to
be serialized by the per-HCD SPI-thread.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NDavid Mosberger <davidm@egauge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid Mosberger <davidm@egauge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit extends the compatible string list of the xhci-platform
binding with the new "renesas,xhci-r8a7790" and "renesas,xhci-r8a7791"
compatible strings. It is used to describe the xHCI controller which
is available in the R-Car H2 and M2 SoCs.
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some platforms (such as the Renesas R-Car) need to initialize some specific
registers after xhci driver calls usb_add_hcd() and before the driver calls
xhci_run(). So, this patch adds the xhci_plat_start() function.
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid Mosberger <davidm@egauge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit c4128cac.

This should come through Felipe's tree first, and there was a bunch of
other patches that are needed after this one as well that I didn't have.

Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As the config option is gone, it's a bit hard to enable it so remove the
reference to it.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that CONFIG_USB_DEBUG is gone, remove it from a number of defconfig
files that were enabling it.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Unconditionally wake up the child device when the power session is
recovered.

This addresses the following scenarios:

1/ The device may need a reset on power-session loss, without this
   change port power-on recovery exposes khubd to scenarios that
   usb_port_resume() is set to handle.  Prior to port power control the
   only time a power session would be lost is during dpm_suspend of the
   hub.  In that scenario usb_port_resume() is guaranteed to be called
   prior to khubd running for that port.  With this change we wakeup the
   child device as soon as possible (prior to khubd running again for this
   port).

   Although khubd has facilities to wake a child device it will only do
   so if the portstatus / portchange indicates a suspend state.  In the
   case of port power control we are not coming from a hub-port-suspend
   state.  This implementation simply uses pm_request_resume() to wake the
   device and relies on the port_dev->status_lock to prevent any collisions
   between khubd and usb_port_resume().

2/ This mechanism rate limits port power toggling.  The minimum port
   power on/off period is now gated by the child device suspend/resume
   latency.  Empirically this mitigates devices downgrading their connection
   on perceived instability of the host connection.  This ratelimiting is
   really only relevant to port power control testing, but it is a nice
   side effect of closing the above race.  Namely, the race of khubd for
   the given port running while a usb_port_resume() event is pending.

3/ Going forward we are finding that power-session recovery requires
   warm-resets (http://marc.info/?t=138659232900003&r=1&w=2).  This
   mechanism allows for warm-resets to be requested at the same point in
   the resume path for hub dpm_suspend power session losses, or port
   rpm_suspend power session losses.

4/ If the device *was* disconnected the only time we'll know for sure is
   after a failed resume, so it's necessary for usb_port_runtime_resume()
   to expedite a usb_port_resume() to clean up the removed device.  The
   reasoning for this is "least surprise" for the user. Turning on a port
   means that hotplug detection is again enabled for the port, it is
   surprising that devices that were removed while the port was off are not
   disconnected until they are attempted to be used.  As a user "why would
   I try to use a device I removed from the system?"

1, 2, and 4 are not a problem in the system dpm_resume() case because,
although the power-session is lost, khubd is frozen until after device
resume.  For the rpm_resume() case pm_request_resume() is used to
request re-validation of the device, and if it happens to collide with a
khubd run we rely on the port_dev->status_lock to synchronize those
operations.

Besides testing, the primary scenario where this mechanism is expected
to be triggered is when the user changes the port power policy
(control/pm_qos_no_poweroff, or power/control).   Each time power is
enabled want to revalidate the child device, where the revalidation is
handled by usb_port_resume().

Given that this arranges for port_dev->child to be de-referenced in
usb_port_runtime_resume() we need to make sure not to collide with
usb_disconnect() that frees the usb_device.  To this end we hold the
port active with the "child_usage" reference across the disconnect
event.  Subsequently, the need to access hub->child_usage_bits lead to
the creation of hub_disconnect_children() to remove any ambiguity of
which "hub" is being acted on in usb_disconnect() (prompted-by sharp
eyes from Alan).

Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Per Alan:
"You mean from within hub_handle_remote_wakeup()?  That routine will
never get called if CONFIG_PM_RUNTIME isn't enabled, because khubd
never sees wakeup requests if they arise during system suspend.

In fact, that routine ought to go inside the "#ifdef CONFIG_PM_RUNTIME"
portion of hub.c, along with the other suspend/resume code."
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In general we do not want khubd to act on port status changes that are
the result of in progress resets or USB runtime PM operations.
Specifically port power control testing has been able to trigger an
unintended disconnect in hub_port_connect_change(), paraphrasing:

	if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
	    udev->state != USB_STATE_NOTATTACHED) {
		if (portstatus & USB_PORT_STAT_ENABLE) {
			/* Nothing to do */
		} else if (udev->state == USB_STATE_SUSPENDED &&
				udev->persist_enabled) {
			...
		} else {
			/* Don't resuscitate */;
		}
	}

...by falling to the "Don't resuscitate" path or missing
USB_PORT_STAT_CONNECTION because usb_port_resume() was in the middle of
modifying the port status.

So, we want a new lock to hold off khubd for a given port while the
child device is being suspended, resumed, or reset.  The lock ordering
rules are now usb_lock_device() => usb_lock_port().  This is mandated by
the device core which may hold the device_lock on the usb_device before
invoking usb_port_{suspend|resume} which in turn take the status_lock on
the usb_port.  We attempt to hold the status_lock for the duration of a
port_event() run, and drop/re-acquire it when needing to take the
device_lock.  The lock is also dropped/re-acquired during
hub_port_reconnect().

This patch also deletes hub->busy_bits as all use cases are now covered
by port PM runtime synchronization or the port->status_lock and it
pushes down usb_device_lock() into usb_remote_wakeup().
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If a port is powered-off, or in the process of being powered-off, prevent
khubd from operating on it.  Otherwise, the following sequence of events
leading to an unintended disconnect may occur:

Events:
(0) <set pm_qos_no_poweroff to '0' for port1>
(1) hub 2-2:1.0: hub_resume
(2) hub 2-2:1.0: port 1: status 0301 change 0000
(3) hub 2-2:1.0: state 7 ports 4 chg 0002 evt 0000
(4) hub 2-2:1.0: port 1, power off status 0000, change 0000, 12 Mb/s
(5) usb 2-2.1: USB disconnect, device number 5

Description:
(1) hub is resumed before sending a ClearPortFeature request
(2) hub_activate() notices the port is connected and sets
    hub->change_bits for the port
(3) hub_events() starts, but at the same time the port suspends
(4) hub_connect_change() sees the disabled port and triggers disconnect
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation for synchronizing port handling with pm_runtime
transitions refactor port handling into its own subroutine.

We expect that clearing some status flags will be required regardless of
the port state, so handle those first and group all non-trivial actions
at the bottom of the routine.

This also splits off the bottom half of hub_port_connect_change() into
hub_port_reconnect() in prepartion for introducing a port->status_lock.
hub_port_reconnect() will expect the port lock to not be held while
hub_port_connect_change() expects to enter with it held.

Other cleanups include:
1/ reflowing to 80 columns
2/ replacing redundant usages of 'hub->hdev' with 'hdev'
3/ consolidate clearing of ->change_bits() in hub_port_connect_change
4/ consolidate calls to usb_reset_device
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The port pm_runtime implementation unconditionally clears FEAT_C_ENABLE
after clearing PORT_POWER, but the bit is reserved on usb3 hub ports.
We expect khubd to be prevented from running because the port state is
not RPM_ACTIVE, so we need to clear any errors for usb2 ports.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Three reasons:
1/ It's an invalid operation on usb3 ports
2/ There's no guarantee of when / if a usb2 port has entered an error
   state relative to PORT_POWER request
3/ The port is active / powered at this point, so khubd will clear it as
   a matter of course
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ClearPortFeature(PORT_POWER) on a usb3 port places the port in either a
DSPORT.Powered-off-detect / DSPORT.Powered-off-reset loop, or the
DSPORT.Powered-off state.  There is no way to ensure that RX
terminations will persist in this state, so it is possible a device will
degrade to its usb2 connection.  Prevent this by blocking power-off of a
usb3 port while its usb2 peer is active, and powering on a usb3 port
before its usb2 peer.

By default the latency between peer power-on events is 0.  In order for
the device to not see usb2 active while usb3 is still powering up inject
the hub recommended power_on_good delay.  In support of satisfying the
power_on_good delay outside of hub_power_on() refactor the places where
the delay is consumed to call a new hub_power_on_good_delay() helper.

Finally, because this introduces several new checks for whether a port
is_superspeed, cache that disctinction at port creation so that we don't
need to keep looking up the parent hub device.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
[alan]: add a 'superspeed' flag to the port
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We want to manipulate ->did_runtime_put in usb_port_runtime_resume(),
but we don't want that to collide with other updates.  Move usb_port
flags to new port-bitmap fields in usb_hub. "did_runtime_put" is renamed
"child_usage_bits" to reflect that it is strictly standing in for the
fact that usb_devices are not the device_model children of their parent
port.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The usb topology after this change will have symlinks between usb3 ports
and their usb2 peers, for example:

usb2/2-1/2-1:1.0/2-1-port1/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port1
usb2/2-1/2-1:1.0/2-1-port2/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port2
usb2/2-1/2-1:1.0/2-1-port3/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port3
usb2/2-1/2-1:1.0/2-1-port4/peer => ../../../../usb3/3-1/3-1:1.0/3-1-port4
usb2/2-0:1.0/usb2-port1/peer    => ../../../usb3/3-0:1.0/usb3-port1
usb2/2-0:1.0/usb2-port2/peer    => ../../../usb3/3-0:1.0/usb3-port2
usb2/2-0:1.0/usb2-port3/peer    => ../../../usb3/3-0:1.0/usb3-port3
usb2/2-0:1.0/usb2-port4/peer    => ../../../usb3/3-0:1.0/usb3-port4

usb3/3-1/3-1:1.0/usb3-1-port1/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port1
usb3/3-1/3-1:1.0/usb3-1-port2/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port2
usb3/3-1/3-1:1.0/usb3-1-port3/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port3
usb3/3-1/3-1:1.0/usb3-1-port4/peer => ../../../../usb2/2-1/2-1:1.0/2-1-port4
usb3/3-0:1.0/usb3-port1/peer       => ../../../usb2/2-0:1.0/usb2-port1
usb3/3-0:1.0/usb3-port2/peer       => ../../../usb2/2-0:1.0/usb2-port2
usb3/3-0:1.0/usb3-port3/peer       => ../../../usb2/2-0:1.0/usb2-port3
usb3/3-0:1.0/usb3-port4/peer       => ../../../usb2/2-0:1.0/usb2-port4

Introduce link_peers_report() to notify on all link_peers() failure
cases.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI identifies peer ports by setting their 'group_token' and
'group_position' _PLD data to the same value.  If a platform has tier
mismatch [1] , ACPI can override the default (USB3 defined) peer port
association for internal hubs.  External hubs follow the default peer
association scheme.

Location data is cached as an opaque cookie in usb_port_location data.

Note that we only consider the group_token and group_position attributes
from the _PLD data as ACPI specifies that group_token is a unique
identifier.

When we find port location data for a port then we assume that the
firmware will also describe its peer port.  This allows the
implementation to only ever set the peer once.  This leads to a question
about what happens when a pm runtime event occurs while the peer
associations are still resolving.  Since we only ever set the peer
information once, a USB3 port needs to be prevented from suspending
while its ->peer pointer is NULL (implemented in a subsequent patch).

There is always the possibility that firmware mis-identifies the ports,
but there is not much the kernel can do in that case.

[1]: xhci 1.1 appendix D figure 131
[2]: acpi 5 section 6.1.8

[alan]: don't do default peering when acpi data present
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Given that root hub port peers are already established, external hub peer
ports can be determined by traversing the device topology:

1/ ascend to the parent hub and find the upstream port_dev

2/ walk ->peer to find the peer port

3/ descend to the peer hub via ->child

4/ find the port with the matching port id

Note that this assumes the port labeling scheme required by the
specification [1].

[1]: usb3 3.1 section 10.3.3
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Assume that the peer of a superspeed port is the port with the same id
on the shared_hcd root hub.  This identification scheme is required of
external hubs by the USB3 spec [1].  However, for root hubs, tier mismatch
may be in effect [2].  Tier mismatch can only be enumerated via platform
firmware.  For now, simply perform the nominal association.

A new lock 'usb_port_peer_mutex' is introduced to synchronize port
device add/remove with peer lookups.  It protects peering against
changes to hcd->shared_hcd, hcd->self.root_hub, hdev->maxchild, and
port_dev->child pointers.

[1]: usb 3.1 section 10.3.3
[2]: xhci 1.1 appendix D

Cc: Alan Stern <stern@rowland.harvard.edu>
[alan: usb_port_peer_mutex locking scheme]
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Once usb-acpi has set the port's connect type the usb_device's
->removable attribute can be set in the standard location
set_usb_port_removable().

This also changes behavior in the case where the firmware says that the
port connect type is unknown.  In that case just use the default setting
determined from the hub descriptor.

Note, we no longer pass udev->portnum to acpi_find_child_device() in the
root hub case since:
1/ the usb-core sets this to zero
2/ acpi always expects zero
...just pass zero.
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The current port name "portX" is ambiguous.  Before adding more port
messages rename ports to "<hub-device-name>-portX"

This is an ABI change, but the suspicion is that it will go unnoticed as
the port power control implementation has been broken since its
introduction.  If however, someone was relying on the old name we can
add sysfs links from the old name to the new name.

Additionally, it unifies/simplifies port dev_printk messages and modifies
instances of:
	dev_XXX(hub->intfdev, ..."port %d"...
	dev_XXX(&hdev->dev, ..."port%d"...
into:
	dev_XXX(&port_dev->dev, ...

Now that the names are unique usb_port devices it would be nice if they
could be included in /sys/bus/usb.  However, it turns out that this
breaks 'lsusb -t'.  For now, create a dummy port driver so that print
messages are prefixed "usb 1-1-port3" rather than the
subsystem-ambiguous " 1-1-port3".

Finally, it corrects an odd usage of sscanf("port%d") in usb-acpi.c.
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A hub indicates whether it supports per-port power control via the
wHubCharacteristics field in its descriptor.  If it is not supported
a hub will still emulate ClearPortPower(PORT_POWER) requests by
stopping the link state machine.  However, since this does not save
power do not bother suspending.

This also consolidates support checks into a
hub_is_port_power_switchable() helper.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB core doesn't properly handle mutual exclusion between
resetting a hub and changing the power states of the hub's ports.  We
need to avoid sending port-power requests to the hub while it is being
reset, because such requests cannot succeed.

This patch fixes the problem by keeping track of when a reset is in
progress.  At such times, attempts to suspend (power-off) a port will
fail immediately with -EBUSY, and calls to usb_port_runtime_resume()
will update the power_is_on flag and return immediately.  When the
reset is complete, hub_activate() will automatically restore each port
to the proper power state.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit fixes the following sparse warning:

drivers/usb/host/pci-quirks.c:
    - 252: warning: symbol 'usb_hcd_amd_remote_wakeup_quirk' was not
      declared. Should it be static?

This function is exported so the fix was to add it's declaration to the
header file.
Signed-off-by: NKonrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 193ab2a6 ("usb: gadget: allow multiple gadgets to be built")
basically renamed the Kconfig symbol USB_GADGET_PXA25X to USB_PXA25X. It
did not rename the related macros in use at that time. Commit
c0a39151 ("ARM: pxa: fix inconsistent CONFIG_USB_PXA27X") did so for
all but one macro. Rename that last macro too now.

Fixes: 193ab2a6 ("usb: gadget: allow multiple gadgets to be built")
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: NBenoit Taine <benoit.taine@lip6.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

TEST 11 unlinks the URB read request for N times. When host and gadget
both initialize pattern 1 (mod 63) data series to do IN transfer, the
host side function should check the data buffer if it is as mod 63
series, because the data packet which host receivced will follow
pattern 1. So this patch adds this checking action.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

TEST 12 and TEST 24 unlinks the URB write request for N times. When
host and gadget both initialize pattern 1 (mod 63) data series to
transfer, the gadget side will complain the wrong data which is not
expected.  Because in host side, usbtest doesn't fill the data buffer
as mod 63 and this patch fixed it.

[20285.488974] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.489181] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.489423] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb50800 length 512 last
[20285.489727] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.490055] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.490281] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.490492] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Active
[20285.490713] dwc3 dwc3.0.auto: ep1out-bulk: endpoint busy
[20285.490909] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Complete
[20285.491117] dwc3 dwc3.0.auto: request ffff8800aa6cb480 from ep1out-bulk completed 512/512 ===> 0
[20285.491431] zero gadget: bad OUT byte, buf[1] = 0
[20285.491605] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Set Stall' params 00000000 00000000 00000000
[20285.491915] dwc3 dwc3.0.auto: Command Complete --> 0
[20285.492099] dwc3 dwc3.0.auto: queing request ffff8800aa6cb480 to ep1out-bulk length 512
[20285.492387] dwc3 dwc3.0.auto: ep1out-bulk: Transfer Not Ready
[20285.492595] dwc3 dwc3.0.auto: ep1out-bulk: reason Transfer Not Active
[20285.492830] dwc3 dwc3.0.auto: ep1out-bulk: req ffff8800aa6cb480 dma aeb51000 length 512 last
[20285.493135] dwc3 dwc3.0.auto: ep1out-bulk: cmd 'Start Transfer' params 00000000 a9eaf000 00000000
[20285.493465] dwc3 dwc3.0.auto: Command Complete --> 0

Cc: <stable@vger.kernel.org>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

USB3503 chip supports 8 values of reference clock. The value is
specified by REF_SEL[1:0] pins and INT_N line. This patch add support
for getting 'refclk' clock, enabling it and setting INT_N line according
to the value of the gathered clock. If no clock has been specified,
driver defaults to the old behaviour (assuming that clock has been
specified by REF_SEL pins from primary reference clock frequencies
table).
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>