Introduced in drbd: always write bitmap on detach,
the bitmap bulk writeout on detach was indicating
it expected exclusive bitmap access.

Where I meant to say: expect no more modifications,
but testing/counting is still allowed.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

We used to calculate all on-disk meta data offsets, and then compare
the stored offsets, basically treating them as magic numbers.

Now with the activity log striping, the activity log size is no longer
fixed.  We need to first read the super block, then base the activity
log and bitmap offsets on the stored offsets/al stripe settings.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Make it obvious that this value is in units of 512 Byte sectors.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Introduce two new on-disk meta data fields: al_stripes and al_stripe_size_4k
The intended use case is activity log on RAID 0 or similar.
Logically consecutive transactions will advance their on-disk position
by al_stripe_size_4k 4kB (transaction sized) blocks.

Right now, these are still asserted to be the backward compatible
values al_stripes = 1, al_stripe_size_4k = 8 (which amounts to 32kB).

Also introduce a caching member for meta_dev_idx in the in-core
structure: even though it is initially passed in in the rcu-protected
disk_conf structure, it cannot change without a detach/attach cycle.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Add a comment about our meta data layout variants,
and rename a few defines (e.g. MD_RESERVED_SECT -> MD_128MB_SECT)
to make it clear that they are short hand for fixed constants,
and not arbitrarily to be redefined as one may see fit.

Properly pad struct meta_data_on_disk to 4kB,
and initialize to zero not only the first 512 Byte,
but all of it in drbd_md_sync().
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

This fixes ASSERT( mdev->state.disk == D_FAILED ) in drivers/block/drbd/drbd_main.c

When we detach from local disk, we let the local refcount hit zero twice.

First, we transition to D_FAILED, so we won't give out new references
to incoming requests; we still may give out *internal* references, though.
Once the refcount hits zero [1] while in D_FAILED, we queue a transition
to D_DISKLESS to our worker.  We need to queue it, because we may be in
atomic context when putting the reference.
Once the transition to D_DISKLESS actually happened [2] from worker context,
we don't give out new internal references either.

Between hitting zero the first time [1] and actually transition to
D_DISKLESS [2], there may be a few very short lived internal get/put,
so we may hit zero more than once while being in D_FAILED, or even see a
race where a an internal get_ldev() happened while D_FAILED, but the
corresponding put_ldev() happens just after the transition to D_DISKLESS.

That's why we have the additional test_and_set_bit(GO_DISKLESS,);
and that's why the assert was placed wrong.
Since there was exactly one code path left to drbd_go_diskless(),
and that checks already for D_FAILED, drop that assert,
and fold in the drbd_queue_work().
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Convert to the much saner new idr interface.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Smatch complained about it this redundanct check.

The check was introduced in 2006-09-13. On 2007-07-24 the body of the
function was enclosed by get_ldev()/put_ldev() reference counting.
Since then the check is useless and miss leading.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

recent commit
    drbd: always write bitmap on detach
introduced a bitmap writeout during detach,
which obviously needs some meta data device to write to.

Unfortunately, that same error path may be taken if we fail to attach,
e.g. due to UUID mismatch, after we changed state to D_ATTACHING,
but before the lower level device pointer is even assigned.

We need to test for presence of mdev->ldev.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

If we detach due to local read-error (which sets a bit in the bitmap),
stay Primary, and then re-attach (which re-reads the bitmap from disk),
we potentially lost the "out-of-sync" (or, "bad block") information in
the bitmap.

Always (try to) write out the changed bitmap pages before going diskless.

That way, we don't lose the bit for the bad block,
the next resync will fetch it from the peer, and rewrite
it locally, which may result in block reallocation in some
lower layer (or the hardware), and thereby "heal" the bad blocks.

If the bitmap writeout errors out as well, we will (again: try to)
mark the "we need a full sync" bit in our super block,
if it was a READ error; writes are covered by the activity log already.

If that superblock does not make it to disk either, we are sorry.

Maybe we just lost an entire disk or controller (or iSCSI connection),
and there actually are no bad blocks at all, so we don't need to
re-fetch from the peer, there is no "auto-healing" necessary.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Without this, the meta-data gets updates after 5 seconds by the
md_sync_timer. Better to do it immeditaly after a state change.

If the asender detects a network failure, it may take a bit until
the worker processes the according after-conn-state-change work item.

  The worker might be blocked in sending something, i.e. it
  takes until it gets into its timeout. That is 6 seconds by
  default which is longer than the 5 seconds of the md_sync_timer.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

If the md_sync_timer triggers a second time,
while the work queued during the first time is still pending,
this could result in list_add() of an already added item,
and corrupt the work item list.

This likely only triggered because of the erroneous
batch-dequeueing of work items fixed with
  drbd: dequeue single work items in wait_for_work()

Still, skip queueing if md_sync_work is already queued.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

There is at least the worker context, the receiver context, the context of
receiving netlink packts.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

To avoid confusion with REQ_DISCARD aka TRIM, rename our
"discard concurrent write acks" from P_DISCARD_WRITE to P_SUPERSEDED.

At the same time, rename the drbd request event DISCARD_WRITE
to CONFLICT_RESOLVED. It already triggers both successful completion
or restart of the request, depending on our RQ_POSTPONED flag.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In 8.4, we may have bios spanning two activity log extents.
Fixup drbd_al_begin_io() and drbd_al_complete_io() to deal with zero sized bios.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

If the drbd worker thread is synchronously waiting for some userland
callback, we don't want some casual pageout to block on us.
Have drbd_congested() report congestion in that case.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Aborting local requests (not waiting for completion from the lower level
disk) is dangerous: if the master bio has been completed to upper
layers, data pages may be re-used for other things already.
If local IO is still pending and later completes,
this may cause crashes or corrupt unrelated data.

Only abort local IO if explicitly requested.
Intended use case is a lower level device that turned into a tarpit,
not completing io requests, not even doing error completion.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Sometimes, a lower level block device turns into a tar-pit,
not completing requests at all, not even doing error completion.

We can force-detach from such a tar-pit block device,
either by disk-timeout, or by drbdadm detach --force.

Queueing for retry only from the request destruction path (kref hit 0)
makes it impossible to retry affected read requests from the peer,
until the local IO completion happened, as the locally submitted
bio holds a reference on the drbd request object.

If we can only complete READs when the local completion finally
happens, we would not need to force-detach in the first place.

Instead, queue for retry where we otherwise had done the error completion.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch

The logic for when to get or put a reference is in mod_rq_state().

To not get confused in the freeze/thaw respectively resend/restart
paths, or when cleaning up requests waiting for P_BARRIER_ACK, this
also introduces additional state flags:
RQ_COMPLETION_SUSP, and RQ_EXP_BARR_ACK.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The previous commit causes __drbd_make_request() to always return 0.
Change it to void.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch

DRBD requests (struct drbd_request) are already on the per resource
transfer log list, and carry their epoch number. We do not need to
additionally link them on other ring lists in other structs.

The drbd sender thread can recognize itself when to send a P_BARRIER,
by tracking the currently processed epoch, and how many writes
have been processed for that epoch.

If the epoch of the request to be processed does not match the currently
processed epoch, any writes have been processed in it, a P_BARRIER for
this last processed epoch is send out first.
The new epoch then becomes the currently processed epoch.

To not get stuck in drbd_al_begin_io() waiting for P_BARRIER_ACK,
the sender thread also needs to handle the case when the current
epoch was closed already, but no new requests are queued yet,
and send out P_BARRIER as soon as possible.

This is done by comparing the per resource "current transfer log epoch"
(tconn->current_tle_nr) with the per connection "currently processed
epoch number" (tconn->send.current_epoch_nr), while waiting for
new requests to be processed in wait_for_work().
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch
In 8.4, we don't distinguish between "resource work" and "connection
work" yet, we have one worker for both, as we still have only one connection.

We only ever used the "data.work",
no need to keep the "meta.work" around.

Move tconn->data.work to tconn->sender_work.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch

In 8.4, we still use drbd_queue_work_front(),
so in normal operation, we can not dequeue batches,
but only single items.

Still, followup commits will wake the worker
without explicitly queueing a work item,
so up() is replaced by a simple wake_up().
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked from drbd 9 devel branch.

In preparation of multiple connections, the "barrier number" or
"epoch number" needs to be tracked per-resource, not per connection.
The sequence number space will not be reset anymore.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Meanwhile, this is used to restart failed READ requests as well.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The buffer 'sc.cpu_mask' is a kernel buffer.  If bitmap_parse is used
instead of __bitmap_parse the extra parameter that indicates a kernel
buffer is not needed.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Transfer log epochs, and therefore P_BARRIER packets,
are per resource, not per volume.
We must not associate them with "some random volume".
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

w_restart_write(), run from worker context, calls __drbd_make_request()
and further drbd_al_begin_io(, delegate=true), which then
potentially deadlocks.  The previous patch moved a BUG_ON to expose
such call paths, which would now be triggered.

Also, if we call __drbd_make_request() from resource worker context,
like w_restart_write() did, and that should block for whatever reason
(!drbd_state_is_stable(), resource suspended, ...),
we potentially deadlock the whole resource, as the worker
is needed for state changes and other things.

Create a dedicated retry workqueue for this instead.

Also make sure that inc_ap_bio()/dec_ap_bio() are properly paired,
even if do_retry() needs to retry itself,
in case __drbd_make_request() returns != 0.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We send left-over garbage from the previous packet in P_DATA_REPLY and
P_RS_DATA_REPLY packets. That's bad behaviour.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

This is necessary since the transfer_log on the sending is also
per tconn.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

This is necessary in order to prepare the move of the (receiver side)
epoch list from the device (mdev) to the connection (tconn) objects.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

That is necessary since the whole transfer log is per connection(tconn)
and not per device(mdev).

This bug caused list corruption on the worker list. When a barrier is queued
for sending in the context of one device, another device did not see the
CREATE_BARRIER bit, and queued the same object again -> list corruption.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

* drbd-8.3:
  drbd: O_SYNC gives EIO on ramdisks for some kernels (eg. RHEL6).
  drbd: send intermediate state change results to the peer
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

* drbd-8.3:
  drbd: fix spurious meta data IO "error"
  drbd: Fixed a race condition between detach and start of resync
  drbd: fix harmless race to not trigger an ASSERT
  drbd: Derive sync-UUIDs only from the bitmap-uuid if it is non-zero
  drbd: Fixed current UUID generation (regression introduced recently, after 8.3.11)
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>