The names of STI and CLI macros were derived from i386 arch historically,
but their name are incomprehensible.
So, for easy to understand, rename these macros to ENABLE_INTERRUPTS
and DISABLE_INTERRUPTS, respectively.
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

This patch fixes the following compile error:
<--  snip  -->
 ...
  AS      arch/m32r/kernel/entry.o
/home/bunk/linux/kernel-2.6/linux-2.6.23-rc3-mm1/arch/m32r/kernel/entry.S: Assembler messages:
/home/bunk/linux/kernel-2.6/linux-2.6.23-rc3-mm1/arch/m32r/kernel/entry.S:358: Error: bad instruction `addi r0,#(((((0)+(64))+(32))+(32)))'
make[2]: *** [arch/m32r/kernel/entry.o] Error 1
<--  snip  -->
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Cc: Adrian Bunk <bunk@kernel.org>

- Separate sys_call_table from arch/m32r/kernel/entry.S and
  move it to arch/m32r/kernel/system_call.S.
- Change sys_call_table section from .data to .rodata.
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

- Remove unused symbols *_MASK
- Change indentation of comments, etc.
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

If no IRQ request is found in the IRQ check of ei_handler,
we can exit directly by jumping "restore_all", instead of via
"ret_from_intr".

This modification is also likely effective for IPI operations,
because scheduler call never happen at the exit of IPIs.
Signed-off-by: NHitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

Simplify and clean up messy ei_handler code in arch/m32r/kernel/entry.S.
- Remove ifdef's for CONFIG_CHIP_* configulations.
- Rearrange the M32700 workaround code.
- Remove the messy platform-dependent interrupt check routines and
  consolidate them to common INT0/INT1/INT2 check routines for all
  platforms with cascaded interrupt controllers.
Signed-off-by: NHitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

On some m32r platforms, cascaded ICUs are used.
This patch is required to simplify ei_handler and consolidate platform-
dependent ICU check routines.

  platform       ICU/INT1  ICU/INT0  ICU/INT2
 --------------  --------  --------  --------
  m32104ut        o         -         -
  m32700ut        o         o         o
  opsput          o         o         o
  usrv            o         -         -
  (others)        -         -         -
Signed-off-by: NHitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

Move dot.gdbinit files from arch/m32r/{platforms}/dot.gdbinit*
to arch/m32r/platforms/{platform}/.
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

Rearrange platform-dependent codes from arch/m32r/kernel/*.c
to arch/m32r/platforms/{platform}/.
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

Add usrv_defcofig file for the usrv (M32R MicroServer) platform.

  platform    defconfig                 Note
 ----------  ----------------------    ---------------------------
  usrv        usrv_defconfig            SMP
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

Update defconfig files for 2.6.23-rc1 in arch/m32r/configs/.
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

Change defconfig file's location from arch/m32r/{platform}/defconfig*
to arch/m32r/configs/{platform}_defconfig.

Applying this patch, we can use defconfig file for each m32r platform
easily, like other architectures.

  ex. Setup defconfig for cross-building
    $ make ARCH=m32r CROSS_COMPILE=m32r-linux-gnu- {platform}_defconfig.

  platform    defconfig                 Note
 ----------  ----------------------    ---------------------------
  m32104ut    m32104ut_defconfig        MMU-less
  m32700ut    m32700ut.smp_defconfig    SMP
  m32700ut    m32700ut.up_defconfig     UP
  mappi       mappi.smp_defconfig       SMP
  mappi       mappi.up_defconfig        UP
  mappi       mappi.nommu_defconfig     MMU-less
  mappi2      mappi2.opsp_defconfig     FPGA env. (CPU Core: OPSP)
  mappi2      mappi2.vdec2_defconfig    FPGA env. (CPU Core: VDEC2)
  mappi3      imappi3.smp_defconfig     SMP
  oaks32r     oaks32r_defconfig         MMU-less
  opsput      opsput_defconfig          UP
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
  [x86 setup] Don't rely on the VESA BIOS being register-clean

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ehca: SRQ fixes to enable IPoIB CM
  IB/ehca: Fix Small QP regressions

This avoids the recent NFS mount regression (returning EBUSY when
mounting the same filesystem twice with different parameters).

The best I can do given the constraints appears to be to have the kernel
first look for a superblock that matches both the fsid and the
user-specified mount options, and then spawn off a new superblock if
that search fails.

Note that this is not the same as specifying nosharecache everywhere
since nosharecache will never attempt to match an existing superblock.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: NHua Zhong <hzhong@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

lguest didn't initialize the kernel stack the way a real i386 kernel
does, and ended up triggering a corner-case in the stack frame checking
that doesn't happen on naive i386, and that the stack dumping didn't
handle quite right.

This makes the frame handling more correct, and tries to clarify the
code at the same time so that it's a bit more obvious what is going on.

Thanks to Rusty Russell for debugging the lguest failure-

Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The HPET clocksource in drivers/char/hpet.c was written as generic code
for ia64, but it is not yet ready to replace the native HPET clocksource
implementations that the i386/x86-64 architectures use.

On x86[-64], trying to register this clocksource results in potentially
multiple hpet-based clocksources being registered, and if the ia64 one
is chosen on x86_64 some users have experienced hangs.

Eventually all three architectures may end up using the same code, but
that is not the case right now.

Cc: John Stultz <johnstul@us.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paolo Ornati <ornati@fastwebnet.it>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  - cxgb3 engine microcode load
  cxgb3 - Fix dev->priv usage
  qeth: Drop ARP packages on HiperSockets interface with NOARP attribute.
  qeth: provide specific message for OSA-adapters exclusively used
  qeth: crash during reboot after failing online setting
  qeth: Announce tx checksumming for qeth devices in TSO/EDDP mode
  qeth: dont return the return values of void functions.
  qeth: enforce a rate limit for inbound scatter gather messages
  qeth: ungrouping a device must not be interruptible
  netxen: fix crashes during module unload
  netxen: Avoid firmware load in PCI probe
  PS3: fix the bug that 'ifconfig down' would hang
  IOC3: Program UART predividers.

Fix ehca SRQ support so that IPoIB connected mode works:

 - Report max_srq > 0 if SRQ is supported
 - Report "last wqe reached" asynchronous event when base QP dies;
   this is required by the IB spec and IPoIB CM relies on receiving it
   when cleaning up.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The new Small QP code had a few bugs that would also make it trigger
for non-Small QPs.  Fix them.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The VESA BIOS is specified to be register-clean.  However, we have now
found at least one system which violates that.  Thus, be as paranoid
about VESA calls as about everything else.

Huge thanks to Will Simoneau for reporting, diagnosing, and testing
this out on Dell Inspiron 5150.

Cc: Will Simoneau <simoneau@ele.uri.edu>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: clean up task_new_fair()
  sched: small schedstat fix
  sched: fix wait_start_fair condition in update_stats_wait_end()
  sched: call update_curr() in task_tick_fair()
  sched: make the scheduler converge to the ideal latency
  sched: fix sleeper bonus limit

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] Bump driver versions
  ata_piix: implement IOCFG bit18 quirk
  libata: implement BROKEN_HPA horkage and apply it to affected drives
  sata_promise: FastTrack TX4200 is a second-generation chip
  pata_marvell: Add more identifiers
  ata_piix: add Satellite U200 to broken suspend list
  ata: add ATA_MWDMA* and ATA_SWDMA* defines
  ata_piix: IDE mode SATA patch for Intel Tolapai
  libata-core: Allow translation setting to fail

Load the engine microcode when an interface
is brought up, instead of of doing it when the module
is loaded.
Loosen up tight binding between the driver and the
engine microcode version.
There is no need for microcode update with T3A boards.
Fix the file naming.
Do a better job at logging the loading activity.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

cxgb3 used netdev_priv() and dev->priv for different purposes.
In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix.
This patch is a partial backport of Dave Miller's changes in the
net-2.6.24 git branch.

Without this fix, cxgb3 crashes on 2.6.23.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A network interface can get ARP packets even when the interface has
NOARP specified. In a HiperSockets environment this disturbs receiving
systems when packets are sent on the multicast queue. (E.g. TCP/IP on
z/VM issues messages reporting invalid data on the HiperSockets
interface.)
Qeth will no longer send ARP packets on HiperSockets interface when
interface has the NOARP attribute.
Signed-off-by: NKlaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Exclusive usage of OSA-cards has been introduced. Even though Linux
does not make use of it, qeth should be prepared to receive a bad RC
for some initialization steps. A meaningful message is now given,
if an OSA-device is set online, even though the OSA-adapter is already
exclusively used by another host.
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Online setting of a qeth device may fail for instance because of:
- out-of-memory condition when allocating qdio queues
- IDX ACTIVATE problem
- ...
Such a device is still returned in a driver_for_each_device loop
processed in qeth_reboot_event(), which calls
qeth_clear_qdio_buffers(). Make sure qeth_clear_output_buffer() is
called only, if the qdio queues have been successfully allocated
during initialization of a qeth device.
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

TSO requires tx checksumming. For non GSO frames in TSO/EDDP mode we
have to manually calculate the checksum.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

under memory pressure scatter gather mode switching messages must be
rate limited.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Problem:
A recovery thread must not be active when device is removed.
In qeth_remove_device() an interruptible wait operation is used
to wait until a qeth recovery thread is finished. If a user really
interrupts the ungroup operation of a qeth device while a recovery
is running, cio and qeth are out of sync (device already removed
from cio, but kept in qeth). A following module unload of qeth
results in a kernel OOPS here.

Solution:
Do not allow interruption of ungroup operation to guarantee
finishing of a potentially running qeth recovery thread.
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes two problems during driver unload. The pci_disable_device()
call is before firmware reload, causing reads and writes across PCI bus after
disabling device. Second problem is the register window was wrong during
firmware reload

Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Loading firmware during PCI probe can lead to incorrect initialization,
rendering the card unusable until next reboot.  This was introduced a while
ago as a workaround for firmware bug, a better workaround was submitted for
this a while ago. So removing original hack that loads firmware during probe.

Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix the bug that 'ifconfig eth0 down' would hang up, reported by Stefan
Assmann <sassmann@suse.de>.
As we removed netif_poll_enable() from dev->open(), we should not use
netif_poll_disable() in dev->stop().
Signed-off-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The IOC3 driver's UART detection bits used to rely on the the firmware
setting the UART pre-divider in a way that's apropriate for the 8250
driver which doesn't currently program this register.  This happens
to work for the console but not rarely for additional ports.

While at it, also program the UART to RS-232 PIO mode; it the UART might
have been in mac-serial and/or DMA mode though that hasn't actually been
observed in practice.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Bump the versions for drivers that were modified, but had not already
had a version number bump.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Page migration currently does not check if the target of the move contains
nodes that that are invalid (if root attempts to migrate pages)
and may try to allocate from invalid nodes if these are specified
leading to oopses.

Return -EINVAL if an offline node is specified.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For hugepage mappings, the file offset, like the address and size, needs to
be aligned to the size of a hugepage.

In commit 68589bc3, the check for this was
moved into prepare_hugepage_range() along with the address and size checks.
 But since BenH's rework of the get_unmapped_area() paths leading up to
commit 4b1d8929, prepare_hugepage_range()
is only called for MAP_FIXED mappings, not for other mappings.  This means
we're no longer ever checking for an aligned offset - I've confirmed that
mmap() will (apparently) succeed with a misaligned offset on both powerpc
and i386 at least.

This patch restores the check, removing it from prepare_hugepage_range()
and putting it back into hugetlbfs_file_mmap().  I'm putting it there,
rather than in the get_unmapped_area() path so it only needs to go in one
place, than separately in the half-dozen or so arch-specific
implementations of hugetlb_get_unmapped_area().
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>