make action upon failure in "drm_atomic_add_affected_connectors()"
consistent with the rest of failures in amdgpu_dm_atomic_check().
Signed-off-by: NShirish S <shirish.s@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
If timing and bpp of displays on mst hub are not changed,
pbn, slot_num for displays should not be changed. Linux
user mode may initiate atomic_check with different display
configuration after set mode finished. This will call to
amdgpu_dm to re-compute payload, slot_num of displays and
saved to dm_connect_state. stream->timing.flags.dsc, pbn,
slot_num are updated to values which may be different from
that were used for set mode. when dsc hub with 3 4k@60hz dp
connected, 3 dsc engines are enabled. timing.flags.dsc = 1.
timing.flags.dsc are changed to 0 due to atomic check. when
dsc hub is unplugged, amdgpu driver check timing.flags.dsc
for last mode set and find out flags.dsc = 0, then does not
disable dsc.

[HOW]
check status of  displays on dsc mst hubs. re-compute pbn,
slot_num, timing.flags.dsc only if there is mode, connect
or enable/disable change.
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NHersen Wu <hersenwu@amd.com>
Reviewed-by: NMikita Lipski <Mikita.Lipski@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

commit 652de07a ("drm/amd/display: Fully switch to dmub for all dcn21
asics") switched over to using dmub on Renoir to fix Gitlab 1735, but this
implied a new dependency on newer firmware which might not be met on older
kernel versions.

Since sw_init runs before hw_init, there is an opportunity to determine
whether or not the firmware version is new to adjust the behavior.

Cc: Roman.Li@amd.com
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1772
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1735
Fixes: 652de07a ("drm/amd/display: Fully switch to dmub for all dcn21 asics")
Signed-off-by: NMario Limonciello <mario.limonciello@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
DMUB binary is common for both A0 and B0. Hence, driver should
notify FW about the support for DPIA in B0.

[How]
Added dpia_supported bit in dmub_fw_boot_options and will be set
only for B0.

Assign dpia_supported to true before dm_dmub_hw_init
in B0 case.

v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Signed-off-by: NJude Shih <shenshih@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Notify data from outbox corrupt, the notify type should be 2 (HPD) instead of 0
(No data). We copied the address instead of the value. The memory might be
freed in the end of outbox IRQ

[How]
We should allocate the memory of notify and copy the whole content from outbox to
hpd handle function

Fixes: 88f52b1f ("drm/amd/display: Support for SET_CONFIG processing with DMUB")
Signed-off-by: NJude Shih <shenshih@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
B0 has pipe mux for DIGC and DIGD which can be connected to PHYF/PHYG or
PHYC/PHY D.

[How]
Based on chip internal hardware revision id determine it is B0 and set
DMUB scratch register so DMUBFW can connect the display pipe is
connected correctly to the dig.

Cc: Wayne Lin <wayne.lin@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NHansen <Hansen.Dsouza@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Stutter mode is a power saving feature on GPUs, however at
least one early raven system exhibits stability issues with
it.  Add a quirk to disable it for that system.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214417
Fixes: 00544006 ("drm/amdgpu: enable gfxoff again on raven series (v2)")
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Need to guard some things with CONFIG_DRM_AMD_DC_DCN.

Fixes: 41724ea2 ("drm/amd/display: Add DP 2.0 MST DM Support")
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NLyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211027223914.1776061-1-alexander.deucher@amd.com

[Why]
Add DP2 MST and debugfs support

[How]
Update the slot info based on the link encoding format
Reviewed-by: N"Lin, Wayne" <Wayne.Lin@amd.com>
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NFangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: NLyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025223825.301703-5-lyude@redhat.com

This reverts commits ddab8bd7 ("drm/amd/display: Fix two cursor duplication
when using overlay") and e7d9560a ("Revert "drm/amd/display: Fix overlay
validation by considering cursors"").

tl;dr ChromeOS uses the atomic interface for everything except the cursor. This
is incorrect and forces amdgpu to disable some hardware features. Let's revert
the ChromeOS-specific workaround in mainline and allow the Chrome team to keep
it internally in their own tree.

See [1] for more details. This patch is an alternative to [2], which added
ChromeOS detection.

[1]: https://lore.kernel.org/amd-gfx/JIQ_93_cHcshiIDsrMU1huBzx9P9LVQxucx8hQArpQu7Wk5DrCl_vTXj_Q20m_L-8C8A5dSpNcSJ8ehfcCrsQpfB5QG_Spn14EYkH9chtg0=@emersion.fr/
[2]: https://lore.kernel.org/amd-gfx/20211011151609.452132-1-contact@emersion.fr/Signed-off-by: NSimon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: ddab8bd7 ("drm/amd/display: Fix two cursor duplication when using overlay")
Fixes: e7d9560a ("Revert "drm/amd/display: Fix overlay validation by considering cursors"")
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
On renoir usb-c port stops functioning on resume after f/w update.
New dmub firmware caused regression due to conflict with dmcu.
With new dmub f/w dmcu is superseded and should be disabled.

[How]
- Disable dmcu for all dcn21.

Check dmesg for dmub f/w version.
The old firmware (before regression):
[drm] DMUB hardware initialized: version=0x00000001
All other versions require this patch for renoir.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1735Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Tested-by: NMario Limonciello <mario.limonciello@amd.com>
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
For optimal power savings on panels that can support it.

This was previously left disabled by default because of issues with
compositors that do not pageflip and scan out directly to the
frontbuffer.

For these compositors we now have detection methods that wait for x
number of pageflips after a full update - triggered by a buffer or
format change typically.

This may introduce bugs or new cases not tested by users so this is
only currently targeting newer DCN.

[How]
Add code in DM to set PSR state by default for newer DCN while falling
back to the feature mask for older.

Add a global debug flag that can be set to disable it for either.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The current logic checks whether the cursor plane blending
properties match the primary plane's. However that's wrong,
because the cursor is painted on all planes underneath. If
the cursor is over the primary plane and the overlay plane,
it's painted on both pipes.

Iterate over the CRTC planes and check their scaling match
the cursor's.

v4: fix typo in commit message (Harry)
Signed-off-by: NSimon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
For those video format with 60 fps, the user space player could
ask for 120Hz for playback.

[How]
Add 120 in the table of common rates.
Signed-off-by: NSolomon Chiu <solomon.chiu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Condition variable sometimes terminated unexpectedly

[How]
Use wait_for_completion_timeout to avoid unexpected termination of CV
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NWayne Lin <Wayne.Lin@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NJude Shih <shenshih@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
1. HPD callback function has deadlock problem
2. HPD status is not assigned
3. There is crash due to null pointer
4. link_enc is NULL in DPIA case

[How]
1. Fix deadlock problem by moving it out of the
   drm_modeset_lock
2. Assign HPD status from the notify of outbox
   from dmub FW
3. Fix the crash by checking if pin or enc exists
4. Use link_enc_cfg_get_link_enc_used_by_link to
   dynamically assign
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NWayne Lin <Wayne.Lin@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NJude Shih <shenshih@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.

[How]
1) DMUB posts SET_CONFIG reply as an Outbox1 message of type
   DMUB_OUT_CMD__SET_CONFIG_REPLY.
2) The dmub async to sync mechanism for AUX is modified to accommodate
   SET_CONFIG commands for both command issue and reply code paths.
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NWayne Lin <Wayne.Lin@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NJude Shih <shenshih@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

ind_block_64b_no_128bcl means INDEP_64B && INDEP_128B &&
MAX_COMPRESSED_BLOCK_SIZE == 64B. Only used by gfx10.3.

ind_block_64b means INDEP_64B && !INDEP_128B &&
MAX_COMPRESSED_BLOCK_SIZE == 64B. Only used by gfx9 and gfx10.
Signed-off-by: NMarek Olšák <marek.olsak@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Allow us to query instances versions more cleanly.

Instancing support is not consistent unfortunately. SDMA is a
good example.  Sienna cichlid has 4 total SDMA instances, each
enumerated separately (HWIDs 42, 43, 68, 69).  Arcturus has 8
total SDMA instances, but they are enumerated as multiple
instances of the same HWIDs (4x HWID 42, 4x HWID 43).  UMC
is another example.  On most chips there are multiple
instances with the same HWID.  This allows us to support both
forms.

v2: rebase
v3: clarify instancing support
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Otherwise, we will run into error case path.

v2: fix build when CONFIG_DRM_AMD_DC_DCN is not set
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NGuchun Chen <guchun.chen@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use IP versions rather than asic_type to differentiate
IP version specific features.
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use IP versions rather than asic_type to differentiate
IP version specific features.

v2: drop unrelated change

Acked-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
add display related cyan_skillfish files in.

makefile controlled by CONFIG_DRM_AMD_DC_DCN201 flag.

v2: squash in clang fixes from Harry, Nathan
v3: squash in missing CONFIG_DRM_AMD_DC check (Alex)
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Signed-off-by: NZhan Liu <zhan.liu@amd.com>
Reviewed-by: NCharlene Liu <charlene.liu@amd.com>
Acked-by: NJun Lei <jun.lei@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit 299f040e.

This patchset breaks on intel platforms and was previously NACK'd by
Ville.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fernando Ramos <greenfoo@u92.eu>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211002154542.15800-2-sean@poorly.run

As requested in Documentation/gpu/todo.rst, replace driver calls to
drm_modeset_lock_all() with DRM_MODESET_LOCK_ALL_BEGIN() and
DRM_MODESET_LOCK_ALL_END()
Signed-off-by: NFernando Ramos <greenfoo@u92.eu>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210924064324.229457-16-greenfoo@u92.eu

[why]
pci deviceid not passed to dal dc, without proper break,
dcn2.x falls into dcn3.x code path

[how]
pass in pci deviceid, and break once dal_version initialized.
Reviewed-by: NZhan Liu <Zhan.Liu@amd.com>
Acked-by: NAnson Jacob <Anson.Jacob@amd.com>
Signed-off-by: NCharlene Liu <Charlene.Liu@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Stack variable params.backlight_ramping_override is uninitialized, so it
contains junk data

[How]
Initialize the variable to false
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Acked-by: NAnson Jacob <Anson.Jacob@amd.com>
Signed-off-by: NJosip Pavic <Josip.Pavic@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
pci deviceid not passed to dal dc, without proper break,
dcn2.x falls into dcn3.x code path

[how]
pass in pci deviceid, and break once dal_version initialized.
Reviewed-by: NZhan Liu <Zhan.Liu@amd.com>
Acked-by: NAnson Jacob <Anson.Jacob@amd.com>
Signed-off-by: NCharlene Liu <Charlene.Liu@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[Why]
Stack variable params.backlight_ramping_override is uninitialized, so it
contains junk data

[How]
Initialize the variable to false
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Acked-by: NAnson Jacob <Anson.Jacob@amd.com>
Signed-off-by: NJosip Pavic <Josip.Pavic@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[Why]
Currently, the 32bit kernel build fails due to an incorrect string
format specifier. ARRAY_SIZE() returns size_t type as it uses sizeof().
However, we specify it in a string as %ld. This causes a compiler error
and causes the 32bit build to fail.

[How]
Change the %ld to %zu as size_t (which sizeof() returns) is an unsigned
integer data type. We use 'z' to ensure it also works with 64bit build.
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NHayden Goodfellow <Hayden.Goodfellow@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Why:
DC core is being released from DM before it's referenced
from hpd_rx wq destruction code.

How: Move hpd_rx destruction before DC core destruction.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Some games, ie. Doom Eternal, present from compute following compute
post-fx and would benefit from having DCC image stores available.

DCN on gfx10_3 doesn't need INDEPENDENT_128B_BLOCKS = 0 so we can expose
these modifiers capable of DCC image stores.
Signed-off-by: NJoshua Ashton <joshua@froggi.es>
Reviewed-by: NBas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Adds the missing logic to set the correct value of dcc_ind_blk for this tiling version.
Signed-off-by: NJoshua Ashton <joshua@froggi.es>
Reviewed-by: NBas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We don't need to do this workaround if we start setting this value when we fill the plane attributes.
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NJoshua Ashton <joshua@froggi.es>
Reviewed-by: NBas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The "base_addr_is_mc_addr" field was added for dcn3.1 support but
pa_config was never updated to set it to false.

Uninitialized memory causes it to be set to true which results in
address mistranslation and white screen.

[How]
Use memset to ensure all fields are initialized to 0 by default.

Fixes: 64b1d0e8 ("drm/amd/display: Add DCN3.1 HWSEQ")
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NAaron Liu <aaron.liu@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch allows panel orientation quirks from DRM core to be
used. They attach a DRM connector property "panel orientation"
which indicates in which direction the panel has been mounted.
Some machines have the internal screen mounted with a rotation.

Since the panel orientation quirks need the native mode from the
EDID, check for it in amdgpu_dm_connector_ddc_get_modes.
Signed-off-by: NSimon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The "base_addr_is_mc_addr" field was added for dcn3.1 support but
pa_config was never updated to set it to false.

Uninitialized memory causes it to be set to true which results in
address mistranslation and white screen.

[How]
Use memset to ensure all fields are initialized to 0 by default.

Fixes: 64b1d0e8 ("drm/amd/display: Add DCN3.1 HWSEQ")
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NAaron Liu <aaron.liu@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

This patch allows panel orientation quirks from DRM core to be
used. They attach a DRM connector property "panel orientation"
which indicates in which direction the panel has been mounted.
Some machines have the internal screen mounted with a rotation.

Since the panel orientation quirks need the native mode from the
EDID, check for it in amdgpu_dm_connector_ddc_get_modes.
Signed-off-by: NSimon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Intermittently, there presents two occurrences of 0 stream
commits in a single HPD event. Current HDCP sequence does
not consider such scenerio, and will thus disable HDCP.

[How]
Add condition check to include stream remove and re-enable
case for HDCP enable.
Reviewed-by: NBhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
call stack of amdgpu dsc mst pbn, slot num calculation is as below:
-compute_bpp_x16_from_target_bandwidth
-decide_dsc_target_bpp_x16
-setup_dsc_config
-dc_dsc_compute_bandwidth_range
-compute_mst_dsc_configs_for_link
-compute_mst_dsc_configs_for_state

from pbn -> dsc target bpp_x16

bpp_x16 is calulated by compute_bpp_x16_from_target_bandwidth.
Beside pixel clock and bpp, num_slices_h and bpp_increment_div
will also affect bpp_x16.

from dsc target bpp_x16 -> pbn

within dm_update_mst_vcpi_slots_for_dsc,
pbn = drm_dp_calc_pbn_mode(clock, bpp_x16, true);

drm_dp_calc_pbn_mode(int clock, int bpp, bool dsc)
{
  return DIV_ROUND_UP_ULL(mul_u32_u32(clock * (bpp / 16), 64 * 1006),
            8 * 54 * 1000 * 1000);
}

bpp / 16 trunc digits after decimal point. This will cause calculation
delta. drm_dp_calc_pbn_mode does not have other informations,
like num_slices_h, bpp_increment_div. therefore, it does not do revese
calcuation properly from bpp_x16 to pbn.

pbn from drm_dp_calc_pbn_mode is less than pbn from
compute_mst_dsc_configs_for_state. This cause not enough mst slot
allocated to display. display could not visually light up.

[How]
pass pbn from compute_mst_dsc_configs_for_state to
dm_update_mst_vcpi_slots_for_dsc

Cc: stable@vger.kernel.org
Reviewed-by: NScott Foster <Scott.Foster@amd.com>
Acked-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NHersen Wu <hersenwu@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>