Fix omap2_map_common_io for multi-omap
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix dmtimer.c for multi-omap boot. Also remove legacy
clk_enable/disable wrappers that are no longer needed.

Note that the clock handling should be further improved
to make use of the clock aliases.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Allows compiling in omap2 and omap3.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Make get_irqnr_and_base common for mach-omap2 multiboot

Thanks to a tip from Russell King <rmk+kernel@arm.linux.org.uk>,
this also optimizes the code for non-multiboot configurations by
using get_irqnr_preamble.

Note that this will only work currently for 24xx and 34xx.
Support for 44xx can be added later on for basic multiboot,
and similar patch should be done for mach-omap1/entry-macro.S.
Signed-off-by: NTony Lindgren <tony@atomide.com>

These are no longer needed. Note that zoom boards
should now set their own function in uncompress.h
and debug-macro.S for the external UART.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.

NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:

$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
	arch/arm/*/include/*/debug-macro.S
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
[tomi.valkeinen@nokia.com: removed defconfig changes]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
[tomi.valkeinen@nokia.com: removed evm defconfig changes]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The platform data allocated with kmalloc() will become unreachable once
the init is complete, so it should be freed. The problem was discovered
by kmemleak.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This reverts commit 70362511 ("tty: fix race in tty_fasync") and
commit b04da8bf ("fnctl: f_modown should call write_lock_irqsave/
restore") that tried to fix up some of the fallout but was incomplete.

It turns out that we really cannot hold 'tty->ctrl_lock' over calling
__f_setown, because not only did that cause problems with interrupt
disables (which the second commit fixed), it also causes a potential
ABBA deadlock due to lock ordering.

Thanks to Tetsuo Handa for following up on the issue, and running
lockdep to show the problem.  It goes roughly like this:

 - f_getown gets filp->f_owner.lock for reading without interrupts
   disabled, so an interrupt that happens while that lock is held can
   cause a lockdep chain from f_owner.lock -> sighand->siglock.

 - at the same time, the tty->ctrl_lock -> f_owner.lock chain that
   commit 70362511 introduced, together with the pre-existing
   sighand->siglock -> tty->ctrl_lock chain means that we have a lock
   dependency the other way too.

So instead of extending tty->ctrl_lock over the whole __f_setown() call,
we now just take a reference to the 'pid' structure while holding the
lock, and then release it after having done the __f_setown.  That still
guarantees that 'struct pid' won't go away from under us, which is all
we really ever needed.
Reported-and-tested-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NAmérico Wang <xiyou.wangcong@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (w83781d) Request I/O ports individually for probing
  hwmon: (lm78) Request I/O ports individually for probing
  hwmon: (adt7462) Wrong ADT7462_VOLT_COUNT

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: Fix leak of relocs along do_execbuffer error path
  drm/i915: slow acpi_lid_open() causes flickering - V2
  drm/i915: Disable SR when more than one pipe is enabled
  drm/i915: page flip support for Ironlake
  drm/i915: Fix the incorrect DMI string for Samsung SX20S laptop
  drm/i915: Add support for SDVO composite TV
  drm/i915: don't trigger ironlake vblank interrupt at irq install
  drm/i915: handle non-flip pending case when unpinning the scanout buffer
  drm/i915: Fix the device info of Pineview
  drm/i915: enable vblank interrupt on ironlake
  drm/i915: Prevent use of uninitialized pointers along error path.
  drm/i915: disable hotplug detect before Ironlake CRT detect

We incorrectly depended on the 'node_state/node_isset()' functions
testing the node range, rather than checking it explicitly.  That's not
reliable, even if it might often happen to work.  So do the proper
explicit test.
Reported-by: NMarcus Meissner <meissner@suse.de>
Acked-and-tested-by: NBrice Goglin <Brice.Goglin@inria.fr>
Acked-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ASoC: pandora: Add APLL supply to fix audio output
  ALSA: ice1724 - aureon - fix wm8770 volume offset
  ALSA: cosmetic: make hda intel interrupt name consistent with others
  ALSA: hda - Delay switching to polling mode if an interrupt was missing
  ALSA: ctxfi - fix PTP address initialization

Different motherboards have different PNP declarations for
W83781D/W83782D chips. Some declare the whole range of I/O ports (8
ports), some declare only the useful ports (2 ports at offset 5) and
some declare fancy ranges, for example 4 ports at offset 4. To
properly handle all cases, request all ports individually for probing.
After we have determined that we really have a W83781D or W83782D
chip, the useful port range will be requested again, as a single
block.

I did not see a board which needs this yet, but I know of one for lm78
driver and I'd like to keep the logic of these two drivers in sync.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

Different motherboards have different PNP declarations for LM78/LM79
chips. Some declare the whole range of I/O ports (8 ports), some
declare only the useful ports (2 ports at offset 5) and some declare
fancy ranges, for example 4 ports at offset 4. To properly handle all
cases, request all ports individually for probing. After we have
determined that we really have an LM78 or LM79 chip, the useful port
range will be requested again, as a single block.

This fixes the driver on the Olivetti M3000 DT 540, at least.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

The #define ADT7462_VOLT_COUNT is wrong, it should be 13 not 12. All the 
for loops that use this as a limit count are of the typical form, "for 
(n = 0; n < ADT7462_VOLT_COUNT; n++)", so to loop through all voltages 
w/o missing the last one it is necessary for the count to be one greater 
than it is.  (Specifically, you will miss the +1.5V 3GPIO input with count 
= 12 vs. 13.)
Signed-off-by: NRay Copeland <ray.copeland@aprius.com>
Acked-by: N"Darrick J. Wong" <djwong@us.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] Call flush_dcache_page after PIO data transfers in libata-sff.c
  ahci: add Acer G725 to broken suspend list
  libata: fix ata_id_logical_per_physical_sectors
  libata-scsi passthru: fix bug which truncated LBA48 return values

The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs.  As
anticipated, we've run into a buggy BIOS:

[    0.081818] pci 0000:00:14.0: reg 10: [io  0x6000-0x7fff]
[    0.081906] pci 0000:00:14.0: reg 14: [io  0x6100-0x61ff]
[    0.082015] pci 0000:00:14.0: reg 18: [io  0x6200-0x63ff]
[    0.082917] pci 0000:00:14.2: reg 20: [io  0xe000-0xe00f]
[    0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[    0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[    0.088816] PCI: pci_cache_line_size set to 32 bytes
[    0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[    0.089052] pci 0000:00:14.0: can't reserve [io  0x6100-0x61ff]

This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k.  In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff).  This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: NAndres Salomon <dilinger@collabora.co.uk>
Tested-by: NLeigh Porter <leigh@leighporter.org>
Tested-by: NJens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is to make the annotation of percpu variables during the next merge
window less painfull.

Extracted from a patch by Rusty Russell.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: fix r300 vram width calculations
  drm/radeon/kms: rs400/480 MC setup is different than r300.
  drm/radeon/kms: make initial state of load detect property correct.
  drm/radeon/kms: disable HDMI audio for now on rv710/rv730
  drm/radeon/kms: don't call suspend path before cleaning up GPU
  drivers/gpu/drm/radeon/radeon_combios.c: fix warning
  ati_pcigart: fix printk format warning
  drm/r100/kms: Emit cache flush to the end of command buffer. (v2)
  drm/radeon/kms: fix regression rendering issue on R6XX/R7XX
  drm/radeon/kms: move blit initialization after we disabled VGA

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: apply updated fallocate i_size fix
  Btrfs: do not try and lookup the file extent when finishing ordered io
  Btrfs: Fix oopsen when dropping empty tree.
  Btrfs: remove BUG_ON() due to mounting bad filesystem
  Btrfs: make error return negative in btrfs_sync_file()
  Btrfs: fix race between allocate and release extent buffer.

Pandora's external DAC is using 256*Fs output from the TWL4030
codec, and TWL4030 needs to have APLL enabled for it's 256*Fs
output to function.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The volume register is from 0..0x7f and 0..0x1a range is mute.
Also, fix mute combining in wm_vol_put(). The wrong behaviour was
noticed by Peter Christensen.
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This renames the interrupt name in /proc/interrupt.
HDA Intel -> hda_intel

This also eliminates space from the name, probably helping some
parsers.
Don't think anybody depends on this name in userspace
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

My sound codec seems sometimes (very rarely) to omit interrupts (ALC268)
However, interrupt mode still works.
Thus if we get timeout, poll the codec once.

If we get 3 such polls in a row, then switch to polling mode.

This patch is maybe an bandaid, but this might be a workaround for hardware bug.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This was incorrect according to the docs and the UMS driver does
it like this.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Boot testing on my rs480 laptop found the MC idle never happened
on startup, a quick check with AMD found the idle bit is in a different
place on the rs4xx than r300.

Implement a new rs400 mc idle function to fix this.
Signed-off-by: NDave Airlie <airlied@redhat.com>

this was incorrect on my rs480.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Support isn't correct yet and we are getting green tinges on the
displays.
Signed-off-by: NDave Airlie <airlied@redhat.com>