The definition of CPG_AUDIO_CLK_I is SoC-specific, not board-specific.
Hence move it from the board-specific .dts files to the SoC-specific
.dtsi files.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the IMR-LX4 devices in the R8A7796 device tree.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the IMR-LX4 devices in the R8A7795 device tree.

Based on the original (and large) patch by Konstantin Kozhevnikov
<Konstantin.Kozhevnikov@cogentembedded.com>.
Signed-off-by: NKonstantin Kozhevnikov <Konstantin.Kozhevnikov@cogentembedded.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Contrary to popular belief, PPIs connected to a GICv3 to not have
an affinity field similar to that of GICv2. That is consistent
with the fact that GICv3 is designed to accomodate thousands of
CPUs, and fitting them as a bitmap in a byte is... difficult.

Fixes: adbc3695 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

This reverts commits 2c0cba48 ("arm: sun8i: sunxi-h3-h5: Add dt node
for the syscon control module") to 2428fd0f ("arm64: defconfig: Enable
dwmac-sun8i driver on defconfig") and 3432a86e ("arm: sun8i:
orangepipc: use internal phy-mode") to 5a79b4f2 ("arm: sun8i:
orangepi-2: use internal phy-mode") that should be merged
through the arm-soc tree, and end up in merge conflicts and build failures.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As I found by chance while merging another patch, the usage of
a dma-mask in this DT node is wrong for multiple reasons:

- dma-masks are a Linux specific concept, not a general
  hardware feature
- In DT, we use the "dma-ranges" property to describe how DMA
  addresses related between devices.
- The 40-bit mask appears to be completely unnecessary here, as
  the SoC cannot address that much memory anyway, so simply
  asking for a 64-bit mask (as supported by the device) should
  succeed anyway.

The patch to remove the parsing of the property is getting merged
through the crypto tree.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This resolves a build error in the next/dt branch:

In file included from arch/arm64/boot/dts/mediatek/mt6797-evb.dts:16:0:
arch/arm64/boot/dts/mediatek/mt6797.dtsi:15:10: fatal error: dt-bindings/power/mt6797-power.h: No such file or directory

003f5d0c ("arm64: dts: mediatek: add clk and scp nodes for MT6797")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add support for the CC  board from Shenzhen Libre Technology
More information about the board are available here:

https://libre.computer/blog/

Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

This commit modifies the Marvell EBU Armada 7K and 8K Device Tree files
to describe the ICU and GICP units, and use ICU interrupts for all
devices in the CP110 blocks.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property

Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reported-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Enable gpio support for CP and AP on the Marvell Armada 7K/8K SoCs.

The Armada 8K has two CP110 blocks, each having two GPIO controllers.
However, in each CP110 block, one of the GPIO controller cannot be
used: in the master CP110, only the second GPIO controller can be used,
while on the slave CP110, only the first GPIO controller can be used.

On the other side, the Armada 7K has only one CP110, but both its GPIO
controllers can be used.

For this reason, the GPIO controllers are marked as "disabled" in the
armada-cp110-master.dtsi and armada-cp110-slave.dtsi files, and only
enabled in the per-SoC dtsi files.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Enable pinctrl support for CP and AP on the Armada 7K/8K SoCs.

The CP master being different between Armada 7k and Armada 8k. This
commit introduces the intermediates files armada-70x0.dtsi and
armada-80x0.dtsi.

These new files will provide different compatible strings depending of
the SoC family. They will also be the location for the pinmux
configuration at the SoC level.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The new binding for the system controller on cp110 moved the clock
controller into a subnode. This preliminary step will allow to add gpio
and pinctrl subnodes.
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The *-clock-output-names of the cp110-system-controller0 node are not
used anymore, so remove them.
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

New bindings are used for the system controller on the ap806, which
means all clock properties must be converted. Use the new bindings in
the xor nodes.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Since the mdio nodes are disabled by default now, we should explicitly
enable these nodes at the board level when they are used. Enable the
cpm_mdio node for the 8040-mcbin.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add Device Trees for Actions Semiconductor S900 SoC and
uCRobotics Bubblegum-96 board.

UART0/1/4/6 interrupts are guesses.

Cc: 96boards@ucrobotics.com
Signed-off-by: NAndreas Färber <afaerber@suse.de>

Add the description of the xMDIO bus for the Marvell Armada 7k and
Marvell Armada 8k; for both CP110 slave and master. This bus is found
on Marvell Ethernet controllers and provides an interface with the
xMDIO bus.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The cryptographic engine found on the cp110 slave is disabled by default
because of some known limitations. Add a comment to explain why it is
disabled by default.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The cryptographic engine on the master cp110 is now enabled by default
at the SoC level. Remove its dts nodes that were only enabling it.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Enable the cryptographic engine at the SoC level on the master cp110.
This engine is always present and do not depends on any pinmux
configuration.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

By adding this regulator, the SD cards are usable at higher speed
protocols such as SDR104.

This patch was tested with an SD HC card compatible with UHS-I.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The Armada 37xx SoCs has 2 SDHCI interfaces. This patch adds the second
one.

Moreover, the Armada 37xx DB v2 board populates the 2 SDHCI interfaces.

The second interface is using pluggable module that can either
have an SD connector or eMMC on it.
This patch adds support for SD module in the device DT.

[ gregory.clement@free-electrons.com:
 - Add more detail in commit log
 - Sort the dt node in address order
 - Document the SD slot in the dts ]
Signed-off-by: NKonstantin Porotchkin <kostap@marvell.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

When several groups of register address and size are used with reg, then
surround each one by angle bracket.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

This cosmetic patch aligns the compatible string when there are on
several lines.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The initial device tree file was for the board V1.4. Now the V2.0 board
is also available. The same dtb will work for both, but the CON number
have changed, so update the comment in the dts to reflect this.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Sort the reference nodes in alphabetical order to ease the merge of
future nodes.
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Disable the mdio nodes by default in the cp110 slave and master dtsi as
they're not wired on every board.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Explicitly enable the MDIO nodes in the Marvell Armada 7k DB and Marvell
Armada 8k DB. This is needed as the MDIO nodes will be disabled in the
CP 110 slave and master dtsi by a following up patch.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The EIP197 cryptographic engine supports 64 bits address width but is
limited to 40 bits on 7k/8k. Add a dma-mask property in the
cryptographic engine nodes to reflect this.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Enable the 1GB Ethernet interface that lives on the slave CP110,
with its corresponding phy (that oddly lives on the master CP110).
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add the three required clocks for the MDIO interface to be functional
on Armada 8k platforms.  Without this, the CPU hangs, causing RCU
stalls or the system to become unresponsive.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
[Thomas:
 - remove mg_core_clock, since it's a parent of mg_clock
 - also add clock references to the slave CP mdio instance]
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The new binding for the system controller on ap806 moved the clock into a
subnode. This preliminary step will allow to add gpio and pinctrl
subnodes
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The clock-output-names of the ap806-system-controller node are not used
anymore, so remove them.
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Armada 8040 DB is equipped with 4 (2x 10G SFI + 2x 1G RGMII)
ethernet ports of which only one was hitherto enabled.
Because currently mvpp2 driver is capable of supporting only
1G RGMII/SGMII, enable second port from CP slave HW block.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add sdhci support for MACCHIATOBin boards.  This uses the AP806 SDHCI
for eMMC and CP110 master for the SD card slot.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The XORv2 engines in the AP side of the Armada 7K/8K SoCs are using the
AP MS core clock as input, so this commit adds the appropriate clocks
properties.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add nodes for the SPICC controller on GX common dtsi, GXBB and
GXL dtsi files.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add entry for k3-dma driver and i2s/hdmi audio devices.

This enables HDMI audio output.

Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Green <andy@warmcat.com>
Cc: Dave Long <dave.long@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Antonio Borneo <borneo.antonio@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
v2:
* Split core i2s entry into dtsi and hdmi specific bits into
  hikey dts
v4:
* Rework simple-card to use many-dai-links method, as
  there may be other links in the future
v5:
* Rework audio description to use the audio-card-graph method
  as requested by Mark.
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>

Add nodes for WiFi. HiKey960 is using TI WL1837MOD module.
Signed-off-by: NGuodong Xu <guodong.xu@linaro.org>
Signed-off-by: NWei Xu <xuwei5@hisilicon.com>