Added tx_empty callback needed for generic wait-until-sent support.
Without this function, when the port is closed usbserial can't know that
there are still data in the chip's transmit FIFO. The chip gets disabled
and untransmitted data lost. When the actual byte count is reported by
tx-empty the close can be delayed until all data are sent.
Signed-off-by: NKonstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: modify tx_empty error handling ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add helper to access line-control register in order to work around a
cp2108 GET_LINE_CTL bug.

cp2108 GET_LINE_CTL returns the 16-bit value with the 2 bytes swapped.
However, SET_LINE_CTL functions properly. When the driver tries to modify
the register, it reads it, modifies some bits and writes back. Because the
read bytes were swapped, this often results in an invalid value to be
written. In turn, this causes cp2108 respond with a stall. The stall
sometimes doesn't clear properly and cp2108 starts responding to following
valid commands also with stalls, effectively failing.
Signed-off-by: NKonstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: amend commit message, modify probe error handling ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

This change is preparation for implementing a cp2108 bug workaround.
The workaround requires storing some private data. Right now the data is
attached to the USB interface and allocated in the attach() callback.
The bug detection requires USB I/O which is done easier from port_probe()
callback rather than attach(). Since the USB access functions take port
as a parameter, and since the private data is used exclusively by these
functions, it can be allocated in port_probe(). Also, all cp210x devices
have exactly 1 port per USB iterface, so moving private data from the USB
interface to port is trivial.
Signed-off-by: NKonstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Flush all device queues at close in order to work around a cp2108 Tx
queue bug.

Occasionally, writing data and immediately closing the port makes cp2108
stop responding. The device has to be unplugged to clear the error.
The failure is induced by shutting down the device while its Tx queue
still has unsent data. This condition is avoided by issuing PURGE command
from the close() callback.

This change is applied to all cp210x devices. Clearing internal queues on
close is generally good.
Signed-off-by: NKonstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: amend commit message ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

New device IDs shamelessly lifted from the vendor driver.

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This comment is ambiguous since there are other MC73xx devices with
different USB IDs. This USB ID is found in the MC7304 and MC7354.

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This reverts commit d80c0d14
(excluding the change to MAX_BL_NUM, which has since been removed).

The qcserial driver now enables the SET_CONTROL_LINE_STATE request
so that AT URCs will work. Move these devices back to the qcserial
driver, which is used for other devices in this series that follow
the same layout.

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This reverts commit 653cdc13.

The qcserial driver now enables the SET_CONTROL_LINE_STATE request
so that AT URCs will work. Move these devices back to the qcserial
driver, which is used for other devices in this series that follow
the same layout.

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Three Sierra Wireless modems have been found to require the CDC ACM
SET_CONTROL_LINE_STATE request on the AT port in order to receive
unsolicited response codes, most recently the Dell Wireless 5808e
(which is a re-branded Sierra Wireless EM7355). On the other hand,
the Sierra Wireless MC7710 does not seem to need this request, but
it was found to work either way.

Use this request on the AT port of devices with the Sierra Wireless
layout in the qcserial driver. The other modems that were moved to
the option driver to work around this can now be moved back.

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Only the option driver implements the send_setup callback; it uses the
SET_CONTROL_LINE_STATE request in CDC ACM to generate DTR/RTS signals
on the port. This is not driver-specific though and is needed by other
drivers, so move the function to the usb_wwan driver (with formatting
tweaks), and replace the callback pointer with a flag that enables the
request.
Suggested-by: NBjørn Mork <bjorn@mork.no>
Suggested-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This is a partial, context modified revert of commit e463c6dd
("USB: option: handle send_setup blacklisting at probe"), which
introduced an unnecessary struct option_private for storing the
interface number used in option_send_setup. Removing this struct
will allow option_send_setup to be generalized for other drivers.
Suggested-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Remove extra blank lines in the several places where functions were
separated by more than one.
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix non-standard formatting in some of the comments.
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
[johan: minor fixes ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Move request_firmware from edge_startup to download_fw.
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Separate the download and boot mode code from download_fw() into two new
helper functions: do_download_mode() and do_boot_mode().
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Use serial->interface instead of serial->dev for messages in download_fw().
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Remove unused "dev" parameter from build_i2c_fw_hdr() and its caller.
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix potential null-pointer dereference at probe by making sure that the
required endpoints are present.

The whiteheat driver assumes there are at least five pairs of bulk
endpoints, of which the final pair is used for the "command port". An
attempt to bind to an interface with fewer bulk endpoints would
currently lead to an oops.

Fixes CVE-2015-5257.
Reported-by: NMoein Ghasemzadeh <moein@istuary.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is intended to add ZTE device PIDs on kernel.
Signed-off-by: NLiu.Zhao <lzsos369@163.com>
Cc: stable <stable@vger.kernel.org>
[johan: sort the new entries ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

This is an HP-branded Sierra Wireless EM7355:
https://bugzilla.redhat.com/show_bug.cgi?id=1223646#c2Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CustomWare uses the FTDI VID with custom PIDs for their ShipModul MiniPlex
products.
Signed-off-by: NMatthijs Kooijman <matthijs@stdin.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Silence read-urb resubmission errors when the device is going away.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Avoid spamming the logs (e.g. with -EPROTO errors) when attempting to
resubmit the interrupt urb while a disconnect of an in-use device is
being processed.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The scanner (here DS3508) always returns 64 bytes per urb buffer. The first
byte indicates the data length used in the current buffer. There even was
a comment describing this. But the comment also said that we'll send
everything in the buffer to the tty layer. That means sending the actual
barcode data and lots of trailing zeroes. This patch lets the driver only
send the real data.
Signed-off-by: NPhilipp Hachtmann <hachti@hachti.de>
Acked-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver used usb_get_serial_data(port->serial) which compiled but resulted
in a NULL pointer being returned (and subsequently used). I did not go deeper
into this but I guess this is a regression.
Signed-off-by: NPhilipp Hachtmann <hachti@hachti.de>
Fixes: a85796ee ("USB: symbolserial: move private-data allocation to
port_probe")
Cc: stable <stable@vger.kernel.org>     # v3.10
Acked-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace redundant variable use in return statement.
Signed-off-by: NSaurabh Karajgaonkar <skarajga@visteon.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When using Edgeport/416 models with newer firmware (sometime after
firmware version 4.80.0), idle ports are automatically bounced
(disconnected and then reconnected) approximately every 60 seconds.
This breaks programs (e.g: minicom) where idle periods are common,
normal and expected.

I confirmed with the manufacturer (Digi International) that Edgeport/416
models now ship from the factory with firmware that expects periodic
"heartbeat" queries from the driver to keep idle ports alive.  This
patch implements heartbeat support using the mechanism Digi suggested
(periodically requesting an I2C descriptor address) that appears effective
on Edgeports running the newer firmware (that require it) and benign on
Edgeport devices running older firmware.  Since we know that Edgeport
firmware version 4.80 (the version distributed in /lib/firmware/down3.bin
and used for Edgeports that are either running still older versions or
have no onboard non-volatile firmware image) does not require heartbeat
support, this patch schedules heartbeats only on Edgeport/416 devices,
and only if they are running firmware versions newer than 4.80.
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
[johan: minor style changes ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Do what we can to verify that the driver's firmware image is valid
(before attempting to download it to the Edgeport) by adding a new
function, check_fw_sanity(), and a call to it in in download_fw().

Note: It looks like some Edgeports (models like the EP/416 with on-board
E2PROM) may be able to function even if the on-disk firmware image is
bad or missing, iff their local E2PROM versions are valid.  But most
Edgeport models (I've tried EP/1 and EP/8) do not appear to have this
capability and they always rely on the on-disk firmware image.

I tested an implementation that calls the new check_fw_sanity()
function at the top of download_fw() and, rather than simply returning
an error if the firmware image is bad or missing, it saves the result
and defers the decision until later when it may find that it is running
on a E2PROM-equipped device with a valid image.  But I think this is
messier than it is worth (adding still more messiness to the already
very messy download_fw()) for such a marginal possible benefit.  So, at
least for now, I have chosen the much simpler approach of returning an
error whenever edge_startup() fails to load an on-disk firmware image, or
check_fw_sanity() indicates that it is unusable.
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
[johan: drop redundant checksum mask ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

The io_ti driver fails to download firmware to Edgeport
devices such as the EP/416, even when the on-disk firmware image
(/lib/firmware/edgeport/down3.bin) is more current than the version
on the EP/416.  The current download code is broken in a few ways.
Notably it mis-uses global variables OperationalMajorVersion and
OperationalMinorVersion (reading their values before they've been
properly initialized and subsequently initializing them multiple times
without synchronization).  This patch drops the global variables and
replaces the redundant calls to request_firmware()/release_firmware()
in download_fw() with a single call pair in edge_startup(); the firmware
image pointer is then passed to download_fw() and build_i2c_fw_hdr().
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The io_ti driver fails to download firmware to Edgeport devices such as
the EP/416 and EP/421 (devices with on-board E2PROM).  One of the problems
is that the default 1 second timeout in ti_vsend_sync() is insufficient
for download operations.  This patch increases the download timeout to
10 seconds.
Signed-off-by: NPeter E. Berger <pberger@brimson.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This commit fixes the following issues:

1. The 9th bit of buf was believed to be the LSB of divisor's
exponent, but the hardware interprets it as MSB (9th bit) of the
mantissa. The exponent is actually one bit shorter and applies
to base 4, not 2 as previously believed.

2. Loop iterations doubled the exponent instead of incrementing.

3. The exponent wasn't checked for overflow.

4. The function returned requested rate instead of actual rate.

Due to issue #2, the old code deviated from the wrong formula
described in #1 and actually yielded correct rates when divisor
was lower than 4096 by using exponents of 0, 2 or 4 base-2,
interpreted as 0, 1, 2 base-4 with the 9th mantissa bit clear.
However, at 93.75 kbaud or less the rate turned out too slow
due to #2 or too fast due to #2 and #3.

I tested this patch by sending and validating 0x00,0x01,..,0xff
to an FTDI dongle at 234, 987, 2401, 9601, 31415, 115199, 250k,
500k, 750k, 1M, 1.5M, 3M+1 baud. All rates passed.

I also used pv to check speed at some rates unsupported by FTDI:
45 (the lowest possible), 2M, 4M, 5M and 6M-1. Looked sane.
Signed-off-by: NMichal Pecio <michal.pecio@gmail.com>
Fixes: 399aa9a7 ("USB: pl2303: use divisors for unsupported baud
rates")
Cc: stable <stable@vger.kernel.org> # v3.18
[johan: update summary ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add support for the Sierra Wireless AR8550 device with
USB descriptor 0x1199, 0x68AB.

It is common with MC879x modules 1199:683c/683d which
also are composite devices with 7 interfaces (0..6)
and also MDM62xx based as the AR8550.

The major difference are only the interface attributes
02/02/01 on interfaces 3 and 4 on the AR8550. They are
vendor specific ff/ff/ff on MC879x modules.

lsusb reports:

Bus 001 Device 004: ID 1199:68ab Sierra Wireless, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x1199 Sierra Wireless, Inc.
  idProduct          0x68ab
  bcdDevice            0.06
  iManufacturer           3 Sierra Wireless, Incorporated
  iProduct                2 AR8550
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength          198
    bNumInterfaces          7
    bConfigurationValue     1
    iConfiguration          1 Sierra Configuration
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        3
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass         2 Communications
      bInterfaceSubClass      2 Abstract (modem)
      bInterfaceProtocol      1 AT-commands (v.25ter)
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        4
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass         2 Communications
      bInterfaceSubClass      2 Abstract (modem)
      bInterfaceProtocol      1 AT-commands (v.25ter)
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x86  EP 6 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x87  EP 7 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x05  EP 5 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        5
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x88  EP 8 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x89  EP 9 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x06  EP 6 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        6
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x8a  EP 10 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               5
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x8b  EP 11 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x07  EP 7 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval              32
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Cc: Lars Melin <larsm17@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Added the USB IDs 0x413c:0x81b1 for the "Dell Wireless 5809e Gobi(TM) 4G
LTE Mobile Broadband Card", a Dell-branded Sierra Wireless EM7305 LTE
card in M.2 form factor, used eg. in Dell's Latitude E7540 Notebook
series.

"lsusb -v" output for this device:

Bus 002 Device 003: ID 413c:81b1 Dell Computer Corp.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x413c Dell Computer Corp.
  idProduct          0x81b1
  bcdDevice            0.06
  iManufacturer           1 Sierra Wireless, Incorporated
  iProduct                2 Dell Wireless 5809e Gobi™ 4G LTE Mobile Broadband Card
  iSerial                 3
  bNumConfigurations      2
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength          204
    bNumInterfaces          4
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      ** UNRECOGNIZED:  05 24 00 10 01
      ** UNRECOGNIZED:  05 24 01 00 00
      ** UNRECOGNIZED:  04 24 02 02
      ** UNRECOGNIZED:  05 24 06 00 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x000c  1x 12 bytes
        bInterval               9
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        3
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      ** UNRECOGNIZED:  05 24 00 10 01
      ** UNRECOGNIZED:  05 24 01 00 00
      ** UNRECOGNIZED:  04 24 02 02
      ** UNRECOGNIZED:  05 24 06 00 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x000c  1x 12 bytes
        bInterval               9
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        8
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x87  EP 7 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x000a  1x 10 bytes
        bInterval               9
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x86  EP 6 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
        ** UNRECOGNIZED:  2c ff 42 49 53 54 00 01 07 f5 40 f6 00 00 00 00 01 f7 c4 09 02 f8 c4 09 03 f9 88 13 04 fa 10 27 05 fb 10 27 06 fc c4 09 07 fd c4 09
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           95
    bNumInterfaces          2
    bConfigurationValue     2
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower              500mA
    Interface Association:
      bLength                 8
      bDescriptorType        11
      bFirstInterface        12
      bInterfaceCount         2
      bFunctionClass          2 Communications
      bFunctionSubClass      14
      bFunctionProtocol       0
      iFunction               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber       12
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         2 Communications
      bInterfaceSubClass     14
      bInterfaceProtocol      0
      iInterface              0
      CDC Header:
        bcdCDC               1.10
      CDC Union:
        bMasterInterface        12
        bSlaveInterface         13
      CDC MBIM:
        bcdMBIMVersion       1.00
        wMaxControlMessage   4096
        bNumberFilters       32
        bMaxFilterSize       128
        wMaxSegmentSize      1500
        bmNetworkCapabilities 0x20
          8-byte ntb input size
      CDC MBIM Extended:
        bcdMBIMExtendedVersion           1.00
        bMaxOutstandingCommandMessages     64
        wMTU                             1500
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               9
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber       13
      bAlternateSetting       0
      bNumEndpoints           0
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0
      bInterfaceProtocol      2
      iInterface              0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber       13
      bAlternateSetting       1
      bNumEndpoints           2
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0
      bInterfaceProtocol      2
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      2
Device Status:     0x0000
  (Bus Powered)
Signed-off-by: NPieter Hollants <pieter@hollants.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Tests with a Sierra Wireless MC7355 have shown that 1199:9041 devices
also require the option_send_setup() code to be used on the USB
interface for the AT port to make unsolicited response codes work
correctly. Move these devices from the qcserial driver to the option
driver like it has been done for the 1199:68c0 devices in commit
d80c0d14 ("USB: qcserial/option: make
AT URCs work for Sierra Wireless MC73xx").
Signed-off-by: NReinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This fixes a typo in the URL: http://zeitcontrol.de/Signed-off-by: NNik Nyby <nikolas@gnu.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Destroy serial_minors IDR on module exit, reclaiming the allocated memory.

This was detected by the following semantic patch (written by Luis
Rodriguez <mcgrof@suse.com>)

<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@

module_init(init);

@ defines_module_exit @
identifier exit;
@@

module_exit(exit);

@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@

DEFINE_IDR(idr);

@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 idr_destroy(&idr);
 ...
}

@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 +idr_destroy(&idr);
}
</SmPL>
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Cc: stable <stable@vger.kernel.org>	# v3.11
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add the USB serial console device ID for Aruba Networks 7xxx series
controllers which have a USB port for their serial console.
Signed-off-by: NPeter Sanford <peter@sanford.io>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Some of the register names defined here are matching with registers
defined in other places. Like DCR is defined here and DCR is also
a register in mn10300 architecture. So when we are building this with
mn10300, build fails.
To avoid we rename all the registers.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add device Olivetti Olicard 300 (Network Connect: MT6225) - IDs 2020:4000.

T:  Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2020 ProdID=4000 Rev=03.00
S:  Manufacturer=Network Connect
S:  Product=MT6225
C:  #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Signed-off-by: NClaudio Cappelli <claudio.cappelli.linux@gmail.com>
Suggested-by: NLars Melin <larsm17@gmail.com>
Cc: stable <stable@vger.kernel.org>
[johan: amend commit message with devices info ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Added the USB serial device ID for the HubZ dual ZigBee
and Z-Wave radio dongle.
Signed-off-by: NJohn D. Blair <johnb@candicontrols.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>