used a modified checkstack to get the 56 number
(normally checkstack wouldn't show this low a value)

checkstack before:
0x0000012f e1000e_check_options [e1000e]:               272

after:
0x0000012f e1000e_check_options [e1000e]:                56
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb and kfree_skb_clean have no users and in the case of
kfree_skb_clean could cause potential build issues since I cannot find
where it is defined.  Based on the patch in which it was introduced it
appears to have been a bit of leftover code from an earlier version of the
patch in which kfree_skb_clean was dropped in favor of consume_skb.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The registers for RDLEN/TDLEN on i350 have the first 7 bits as read only.
This is a change from previous hardware in which it was only the first 4
bits that were read only.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.

No functional change.

For further information about the background:

http://marc.info/?l=linux-netdev&m=127037540020276&w=2Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Brice Goglin <brice@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.

No functional change.

For further information about the background:

http://marc.info/?l=linux-netdev&m=127037540020276&w=2Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.

No functional change.

For further information about the background:

http://marc.info/?l=linux-netdev&m=127037540020276&w=2Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.

No functional change.

For further information about the background:

http://marc.info/?l=linux-netdev&m=127037540020276&w=2Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.

No functional change.

For further information about the background:

http://marc.info/?l=linux-netdev&m=127037540020276&w=2Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc:  Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.

No functional change.

For further information about the background:

http://marc.info/?l=linux-netdev&m=127037540020276&w=2Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The notifier for address down should only be called if address is completely
gone, not just being marked as tentative on link transistion. The code
in net-next would case bonding/sctp/s390 to see address disappear on link
down, but they would never see it reappear on link up.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since an address in hash list has to already have a ref count,
no additional ref count is needed.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When link goes down, want address to be preserved but in a tentative
state, therefore it has to stay in hash list.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes preserve IPv6 address when link goes down (good).
But would cause address to point to dead dst entry (bad).
The simplest fix is to just not delete route if address is
being held for later use.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.110.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the following checkpatch errors:

* return is not a function, parentheses are not required
* space prohibited between function name and open parenthesis '('
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The maximum packet size that gets programmed into the standard producer
ring control block is directly related to the packet size used to
allocate packet buffers.  This patch removes the redundant preprocessor
constant.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tg3 driver is written so that VLAN tagged packets can be accepted,
even if CONFIG_VLAN_8021Q or CONFIG_VLAN_8021Q_MODULE is not defined.
(Think raw interfaces.)  If the device has ASF support enabled, the
firmware requires the driver to enable VLAN tag stripping.  If VLAN
tagging is not explicitly supported by the kernel and ASF is enabled,
the driver will have to reinject the VLAN tag back into the packet
stream.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a PCIX bus, the 5701 has a bug which requires the driver to double
copy all rx packets.  The rx code uses the rx_offset device member as a
flag to determine if this workaround should take effect.  The following
patch will modify the rx_offset member such that this test will become
less clear.

The patch starts by integrating the workaround check into the packet
length check.  It rounds out the implementation by relaxing the
workaround restrictions if the platform has efficient unaligned
accesses.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reduces the core clock to 6.25MHz when operating at 10Mbps
link speed.  This is needed to prevent a bug that will ultimately cause
transmits to cease.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets the Maximum Read Request Size for the card reader
function to 1024 bytes to prevent an SD controller lockup.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch disables CLKREQ in L2 to workaround a chipset bug.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With latest CONFIG_PROVE_RCU stuff, I felt more comfortable to make this
work.

sk->sk_dst_cache is currently protected by a rwlock (sk_dst_lock)

This rwlock is readlocked for a very small amount of time, and dst
entries are already freed after RCU grace period. This calls for RCU
again :)

This patch converts sk_dst_lock to a spinlock, and use RCU for readers.

__sk_dst_get() is supposed to be called with rcu_read_lock() or if
socket locked by user, so use appropriate rcu_dereference_check()
condition (rcu_read_lock_held() || sock_owned_by_user(sk))

This patch avoids two atomic ops per tx packet on UDP connected sockets,
for example, and permits sk_dst_lock to be much less dirtied.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dont use netdev_warn() in dev_cap_txqueue() and get_rps_cpu() so that we
can catch following warnings without crash.

bond0.2240 received packet on queue 6, but number of RX queues is 1
bond0.2240 received packet on queue 11, but number of RX queues is 1
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a packet has the skb_shared_tx->hardware flag set the device is
instructed to generate a TX timestamp and write it back to memory after
the frame is transmitted. During the clean_tx_ring operation the
timestamp will be extracted and copied into the skb_shared_hwtstamps
struct of the skb.

TX timestamping is enabled by setting the tx_type to something else
than HWTSTAMP_TX_OFF with the SIOCSHWTSTAMP ioctl command. It is only
supported by eTSEC devices.
Signed-off-by: NManfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device is configured to insert hardware timestamps into all
received packets. The RX timestamps are extracted from the padding
alingment bytes during the clean_rx_ring operation and copied into the
skb_shared_hwtstamps struct of the skb. This extraction only happens if
the rx_filter was set to something else than HWTSTAMP_FILTER_NONE with
the SIOCSHWTSTAMP ioctl command.

Hardware timestamping is only supported for eTSEC devices. To indicate
device support the new FSL_GIANFAR_DEV_HAS_TIMER flag was introduced.
Signed-off-by: NManfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for using the LL TEMAC Ethernet driver on
non-Virtex 5 platforms by adding support for accessing the Soft DMA
registers as if they were memory mapped instead of solely through the
DCR's (available on the Virtex 5).

The patch also updates the driver so that it runs on the MicroBlaze.
The changes were tested on the PowerPC 440, PowerPC 405, and the
MicroBlaze platforms.
Signed-off-by: NJohn Tyner <jtyner@cs.ucr.edu>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The virt_to_bus call should not be used any longer as it's
considered illegal. The driver has the physical address of
the buffer in the descriptor such that it's not necessary
anyway.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the SO_TIMESTAMPING socket infrastructure for raw packet sockets.
We introduce PACKET_TX_TIMESTAMP for the control message cmsg_type.

Similar support for UDP and CAN sockets was added in commit
51f31cabSigned-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for SJA1000 based PCI CAN interface cards
from electronic system design gmbh.

Some changes have been done on the common code:
 - esd boards must not have the 2nd local interupt enabled (PLX9030/9050)
 - a new path for PLX9056/PEX8311 chips has been added
 - new plx9056 reset function has been implemented
 - struct plx_card_info got a reset function entry

In detail the following additional boards are now supported:

        CAN-PCI/200 (PCI)
        CAN-PCI/266 (PCI)
        CAN-PMC266 (PMC module)
        CAN-PCIe/2000 (PCI Express)
        CAN-CPCI/200 (Compact PCI, 3U)
        CAN-PCI104 (PCI104)
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Back in commit 04a0551c
("loopback: Drop obsolete ip_summed setting") we stopped
setting CHECKSUM_UNNECESSARY in the loopback xmit.

This is because such a setting was a lie since it implies that the
checksum field of the packet is properly filled in.

Instead what happens normally is that CHECKSUM_PARTIAL is set and
skb->csum is calculated as needed.

But this was only happening for TCP data packets (via the
skb->ip_summed assignment done in tcp_sendmsg()).  It doesn't
happen for non-data packets like ACKs etc.

Fix this by setting skb->ip_summed in the common non-data packet
constructor.  It already is setting skb->csum to zero.

But this reminds us that we still have things like ip_output.c's
ip_dev_loopback_xmit() which sets skb->ip_summed to the value
CHECKSUM_UNNECESSARY, which Herbert's patch teaches us is not
valid.  So we'll have to address that at some point too.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

inet: Remove unused send_check length argument

This patch removes the unused length argument from the send_check
function in struct inet_connection_sock_af_ops.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Tested-by: NYinghai <yinghai.lu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp: Handle CHECKSUM_PARTIAL for SYNACK packets for IPv6

This patch moves the common code between tcp_v6_send_check and
tcp_v6_gso_send_check into a new function __tcp_v6_send_check.

It then uses the new function in tcp_v6_send_synack as well as
tcp_v6_send_response so that they handle CHECKSUM_PARTIAL properly.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Tested-by: NYinghai <yinghai.lu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp: Handle CHECKSUM_PARTIAL for SYNACK packets for IPv4

This patch moves the common code between tcp_v4_send_check and
tcp_v4_gso_send_check into a new function __tcp_v4_send_check.

It then uses the new function in tcp_v4_send_synack so that it
handles CHECKSUM_PARTIAL properly.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Tested-by: NYinghai <yinghai.lu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/stmmac/stmmac_main.c
	drivers/net/wireless/wl12xx/wl1271_cmd.c
	drivers/net/wireless/wl12xx/wl1271_main.c
	drivers/net/wireless/wl12xx/wl1271_spi.c
	net/core/ethtool.c
	net/mac80211/scan.c

This reverts commit 2626419a.

It causes regressions for people with IGB cards.  Connection
requests don't complete etc.  The true cause of the issue is
still not known, but we should sort this out in net-next-2.6
not net-2.6
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/mlx4: Check correct variable for allocation failure
  RDMA/nes: Correct cap.max_inline_data assignment in nes_query_qp()
  RDMA/cm: Set num_paths when manually assigning path records
  IB/cm: Fix device_create() return value check

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] Update default configuration.
  [S390] nss: add missing .previous statement to asm function
  [S390] increase default size of vmalloc area
  [S390] s390: disable change bit override
  [S390] fix io_return critical section cleanup
  [S390] sclp_async: potential buffer overflow
  [S390] arch/s390/kernel: Add missing unlock

* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (34 commits)
  cfq-iosched: Fix the incorrect timeslice accounting with forced_dispatch
  loop: Update mtime when writing using aops
  block: expose the statistics in blkio.time and blkio.sectors for the root cgroup
  backing-dev: Handle class_create() failure
  Block: Fix block/elevator.c elevator_get() off-by-one error
  drbd: lc_element_by_index() never returns NULL
  cciss: unlock on error path
  cfq-iosched: Do not merge queues of BE and IDLE classes
  cfq-iosched: Add additional blktrace log messages in CFQ for easier debugging
  i2o: Remove the dangerous kobj_to_i2o_device macro
  block: remove 16 bytes of padding from struct request on 64bits
  cfq-iosched: fix a kbuild regression
  block: make CONFIG_BLK_CGROUP visible
  Remove GENHD_FL_DRIVERFS
  block: Export max number of segments and max segment size in sysfs
  block: Finalize conversion of block limits functions
  block: Fix overrun in lcm() and move it to lib
  vfs: improve writeback_inodes_wb()
  paride: fix off-by-one test
  drbd: fix al-to-on-disk-bitmap for 4k logical_block_size
  ...