Add device-tree support for the GPMC controller on the OMAP3.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add mcspi node and pinmux data for omap5 mcspi controller.

Tested on omap5430 evm with 3.8-rc6 custom kernel.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add all 4 mcspi instances to omap5.dtsi file.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
[benoit.cousson@linaro.org: Update the subject]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Booting 3.8-rc6 on omap4 panda results in the following error

[    0.444427] omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[    0.445770] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz
[    0.473937] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[    0.474670] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz
[    0.474822] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[    0.476379] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz
[    0.477294] omap_i2c 48350000.i2c: did not get pins for i2c error: -19
[    0.477996] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz
[    0.483398] Switching to clocksource 32k_counter

This happens because omap4 panda dts file is not adapted to use i2c through
pinctrl framework. Populating i2c pinctrl data to get rid of the error.

Tested on omap4460 panda with 3.8-rc6 kernel.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Reported-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Booting 3.8-rc6 on omap 5430evm results in the following error

omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[    1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz
[    1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[    1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[    1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[    1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
[    1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19
[    1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz

This happens because omap5 dts file is not adapted to use i2c through pinctrl
framework. Populating i2c pinctrl data to get rid of the error.

Tested on omap5430 evm with 3.8-rc6 kernel.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add the needed sections to enable audio support on Overo.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Booting 3.8-rc6 on omap 4430sdp results in the following error

omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[    1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz
[    1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[    1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[    1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[    1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
[    1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19
[    1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz

This happens because omap4 dts file is not adapted to use i2c through pinctrl
framework. Populating i2c pinctrl data to get rid of the error.

Tested on omap4430 sdp with 3.8-rc6 kernel.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Reported-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Convert the on-board LED connected to the TWL4030 (LEDB) to use
pwm-leds.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Section to describe the backlight for the LCD panels.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Sections to describe the pwm-leds in the system.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

We have proper driver stack to handle the pmu_stat LED which is connected
PWMB of twl4030.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Enable support for the PWMs and LED as PWM drivers.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Enable support for the PWMs and LEDs as PWM drivers.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add a new address space/memory resource to d_can device tree node. D_CAN
RAM initialization is achieved through RAMINIT register which is part of
AM33XX control module address space. D_CAN RAM init or de-init should be
done by writing instance corresponding value to control module register.

Till we have a separate control module driver to write to control module,
d_can driver will handle the register writes to control module by itself.
So a new address space to represent this control module register is added
to d_can driver.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add d_can instances to aliases node to get the D_CAN instance number
from the driver. To initialize D_CAN message RAM, corresponding instance
number is required.

To initialize instance 0 message RAM then 0x1 should be written and for
instance 1 message RAM, 0x2 should be written to control module register.

With device-tree framework ip instance number is "-1" by default for all
instances. To get device id/instance number then modules should be added
to DT "aliases" node. of_alias_get_id() gives the device id number based
on number of alias nodes present in "aliases node".
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

This is a follow-up to Javier Martinez effort adding initial
device tree support to IGEP technology devices [1].

It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards.

[1] http://www.spinics.net/lists/linux-omap/msg83409.htmlSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

ISEE IGEP COM Module is an TI OMAP3 SoC computer on module.

This patch adds an initial device tree support to boot an
IGEP COM Module from the MMC/SD.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
[b-cousson@ti.com: Update the Makefile for 3.8-rc2]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

ISEE IGEPv2 is an TI OMAP3 SoC based embedded board.

This patch adds an initial device tree support to boot
an IGEPv2 from the MMC/SD.

Currently is working everything that is supported by DT
on OMAP3 SoCs (MMC/SD, GPIO LEDs, EEPROM, TWL4030 audio).
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
[benoit.cousson@linaro.org: Update the Makefile for 3.8-rc2]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add a generic .dtsi device tree source file for the
common characteristics across IGEP Technology devices.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: NMatthias Brugger <matthias.bgg@gmail.com>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Rename I2C and GPIO nodes according to AM33XX TRM. According to
AM33XX TRM device instances are starting from "0" like i2c0, i2c1
and i2c3.
Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com>
[panto@antoniou-consulting.com: initial patch by pantelis's]
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Merge tag 'omap-devel-b-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into for_3.10/dts_merged

Provide RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.

Also provide pin multiplexer information for USB host
pins.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds device nodes for HS USB Host module, TLL module,
OHCI and EHCI controllers.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds device nodes for HS USB Host module, TLL module,
OHCI and EHCI controllers.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove deprecated USBHS platform data.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.

Get rid of managing the PHY clock as it will be done by the PHY driver.
For that to work we create a clock alias that links the PHY clock name
to the PHY device name.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>