Previously, when changing the ring parameters, we free the old
ring resources firstly, and then setup the new ring resources.
In some case of an memory allocation fail, there will be no
resources to use. This patch refines it by setup new ring
resources and free the old ring resources in order.

Also reduce the max ring BD number to 32760 according to UM.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware supports 0.5K, 1K, 2K, 4K RX buffer size, the
RX buffer can not be reused because the hns3_page_order
return 0 when page size and RX buffer size are both 4096.

So this patch changes the hns3_page_order to return 1 when
RX buffer is greater than half of the page size and page size
is less the 8192, and dev_alloc_pages has already been used
to allocate the compound page for RX buffer.

This patch also changes hnae3_* to hns3_* for page order
and RX buffer size calculation because they are used in
hns3 module.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some times just see the eth interface have been down/up via
dmesg, but can not know why the eth down. So adds some debug
messages to identify the cause for this.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some cases, ops->get_reset_level may not be implemented, so we
should check whether it is NULL before calling get_reset_level.
Signed-off-by: NGuangbin Huang <huangguangbin@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hns3_set_channels() should check the resetting status firstly,
since the device will reinitialize when resetting. If the
reset has not completed, the hns3_set_channels() may access
invalid memory.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: NMatthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some bitwise operator used signed type, this patch fixes
them with unsigned type.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The HNS3_RXD_VLD_B bit has already been checked in hns3_add_frag
or hns3_handle_rx_bd before calling hns3_handle_bdinfo, so when
hns3_handle_bdinfo is called, the HNS3_RXD_VLD_B bit is always
set, which makes the checking in hns3_handle_bdinfo unnecessary.

This patch removes the RXD_VLD_B checking in hns3_handle_bdinfo.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The frame column is based on rx_crc_errors and rx_frame_errors. So
l3l4 checksum error should not be counted by rx_crc_errors. Instead,
l3l4 checksum error should be counted in ifconfig error column.

Fixes: d3ec4ef6 ("net: hns3: refactor the statistics updating for netdev")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When change MTU or other operations, which just calling .reset_notify
to do HNAE3_DOWN_CLIENT and HNAE3_UP_CLIENT, then
the netdev_tx_reset_queue() in the hns3_clear_all_ring() will be
ignored. So the dev_watchdog() may misdiagnose a TX timeout.

This patch separates netdev_tx_reset_queue() from
hns3_clear_all_ring(), and unifies hns3_clear_all_ring() and
hns3_force_clear_all_ring into one, since they are doing
similar things.

Fixes: 3a30964a ("net: hns3: delay ring buffer clearing during reset")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We add override_pci_need_reset to prevent redundant and unwanted PF
resets if a RAS error occurs in commit 69b51bbb ("net: hns3: fix
to stop multiple HNS reset due to the AER changes").

Now in HNS3 driver, we use hw_err_reset_req to record reset level that
we need to recover from a RAS error. This variable cans solve above
issue as override_pci_need_reset, so this patch removes
override_pci_need_reset.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix wrong indentation of goto return.
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pointer ae_dev is null checked however, prior to that it is dereferenced
when assigned pointer ops. Fix this by assigning pointer ops after ae_dev
has been null checked.

Addresses-Coverity: ("Dereference before null check")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does following things:
1. add the keyword const before some variables which won't be modified
   in functions.
2. changes some variables from signed to unsigned to avoid bitwise
   operation on signed variables.
3. adds or removes initialization of some variables.
4. defines a new structure to help parsing mailbox messages instead of
   using an array which is harder to get the meaning of each element.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver may not be able to disable the ring through firmware
when downing the netdev during reset process, which may cause
hardware accessing freed buffer problem.

This patch delays the ring buffer clearing to reset uninit
process because hardware will not access the ring buffer after
hardware reset is completed.

Fixes: bb6b94a8 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netdev is dereferenced before null checking in the function
hns3_setup_tc.

This patch moves the dereferencing after the null checking.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In hns3_nic_init_irq(), if request irq fail at index i,
the function return directly without releasing irq resources
that already requested, and nowhere else will release them.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Presently the error handling code sets the reset level required
for the recovery of the hw errors to the reset framework in the
error_detected AER callback. However the rest_event would be
called later from the slot_reset callback. This can cause issue
of using the wrong reset_level if a high priority reset request
occur before the slot_reset is called.

This patch delays setting of the reset level, required
for the hw errors, to the reset framework until the
slot_reset is called.
Reported-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes some coding style issues reported by some static code
analysis tools and code review, such as modify some comments, rename
some variables, log some errors in detail, and fixes some alignment
errors.

BTW, these cleanups do not change the logic of code.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuiSong Li <lihuisong@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since HNAE3_CLIENT_UNIC and HNAE3_DEV_UNIC is not used any more,
this patch removes the redundant codes.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new hns3_get_new_flow_lvl function to calculate
the packet flow level, which is used to decide the interrupt
coalescence parameter, in order to make the flow level calculation
code more readable and make the future calculation ajdustment easier.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces numa_node_id with numa_mem_id when doing buffer
reusing checking, because the buffer still can be reused when the
buffer is from the nearest node and the local node has no memory
attached.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when a GRO packet is assembled by HW, the checksum is
modified to reflect the entire packet by HW and skb->ip_summed is
set to CHECKSUM_UNNECESSARY, which is not compliant with SW GRO.

This patch sets up skb's network and transport header, sets the
GRO packet's checksum according to pseudo header and set the
skb->ip_summed to CHECKSUM_PARTIAL.

This patch also use gso_size to distinguish GRO packet from
normal packet, use eth_type_vlan to check the VLAN type and set
the SKB_GSO_TCP_FIXEDID according to BD info during HW GRO info
processing.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we add a VF without loading hclgevf.ko and then there is a RAS error
occurs, PCIe AER will call error_detected and slot_reset of all functions,
and will get a NULL pointer when we check ad_dev->ops->handle_hw_ras_error.
This will cause a call trace and failures on handling of follow-up RAS
errors.

This patch check ae_dev and ad_dev->ops at first to solve above issues.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In orginal codes, the driver only restore VLAN filter entries
for PF after reset, the VLAN entries of VF will lose in this
case.

This patch fixes it by recording VLAN IDs for each function
when add VLAN, and restore the VLAN IDs after reset.

Fixes: 681ec399 ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hns3_uninit_phy() should be called before checking
HNS3_NIC_STATE_INITED flags, otherwise when this checking fails,
there is nobody to call hns3_uninit_phy().

Fixes: c8a8045b ("net: hns3: Fix NULL deref when unloading driver")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds aRFS support for PF. The aRFS rules are also
stored in the hardware flow director table, Use the existing
filter management functions to insert TCPv4/UDPv4/TCPv6/UDPv6
flow director filters. To avoid rule conflict, once user adds
flow director rules with ethtool, the aRFS will be disabled,
and clear exist aRFS rules. Once all user configure rules were
removed, aRFS can work again.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate CPU rmap and add entry for each irq. CPU rmap is
used in aRFS to get the queue number of the rx completion
interrupts.

In additional, remove the calling of
irq_set_affinity_notifier() in hns3_nic_init_irq(), because
we have registered notifier in irq_cpu_rmap_add() for each
vector, otherwise it may cause use-after-free issue.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pointer l2_hdr is being assigned to itself, this is redundant
and can be removed.

Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses devm_kcalloc instead of kcalloc when allocating
ring->desc_cb, because devm_kcalloc not only ensure to free the
memory when the dev is deallocted, but also allocate the memory
from it's device memory node.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes some unused field in struct hns3_enet_ring,
use ring->dev for ring_to_dev macro, and use dev consistently
in hns3_fill_desc.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When page size is 64K, RX buffer is currently not reused when the
page_offset is moved to last buffer. This patch adds checking to
decide whether the buffer page can be reused when last_offset is
moved beyond last offset.

If the driver is the only user of page when page_offset is moved
to beyond last offset, then buffer can be reused and page_offset
is set to zero.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, a barrier is used when cleaning each TX BD, which may
cause performance degradation.

This patch optimizes it to use one barrier when cleaning TX BD
each round.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When desc filling fails in hns3_nic_net_xmit, it will call
hns3_clear_desc to unmap the dma mapping. But currently the
ring->next_to_use points to the desc where the desc filling
or dma mapping return error, which means the desc that
ring->next_to_use points to has not done the dma mapping,
the desc that need unmapping is before the ring->next_to_use.

This patch fixes it by calling ring_ptr_move_bw(next_to_use)
before doing unmapping operation, and set desc_cb->dma to
zero to avoid freeing it again when unloading.

Also, when filling skb head or frag fails, both need to unmap
all the way back to next_to_use_head, so remove one desc filling
error handling.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When filling len and checksum info to description, there is some
similar checking or calculation.

So this patch adds hns3_set_l2l3l4 to fill the inner(/normal)
header's len and checksum info. If it is a encapsulation skb, it
calls hns3_set_outer_l2l3l4 to handle the outer header's len and
checksum info, in order to avoid some similar checking or
calculation.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch separates the inner and outer l2l3l4 len handling in
hns3_set_l2l3l4_len, this is a preparation to combine the l2l3l4
len and checksum handling for inner and outer header.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to hardware user manual, the tunnel packet type is
available in the rx.ol_info field of struct hns3_desc. Currently
the tunnel packet type is decided by the rx.l234_info, which may
cause RX checksum handling error.

This patch fixes it by using the correct field in struct hns3_desc
to decide the tunnel packet type.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW requires every continuous 8 buffer data to be larger than MSS,
we simplify it by ensuring skb_headlen + the first continuous
7 frags to to be larger than GSO header len + mss, and the
remaining continuous 7 frags to be larger than MSS except the
last 7 frags.

This patch adds hns3_skb_need_linearized to handle it for TSO
case.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, using "ethtool --statistics" can show how many time RX
page have been reused, but there is no counter for RX page not
being reused.

This patch adds non_reuse_pg counter to better debug the performance
issue, because it is hard to determine when the RX page is reused
or not if there is no such counter.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

napi_schedule_irqoff is introduced to be used from hard interrupts
handlers or when irqs are already masked, see:

https://lists.openwall.net/netdev/2014/10/29/2

So this patch replaces napi_schedule with napi_schedule_irqoff.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>