- 04 8月, 2015 3 次提交
-
-
由 Eliad Peller 提交于
Some CSR registers have to be configured also in case of suspend/resume with unified image (which doesn't includes reconfiguration flow). Reuse the existing d3_suspend/d3_resume trans ops, while making sure some configurations are a bit different, according to the wowlan type. After this change, we no longer need the special wowlan_d0i3 configurations done in iwl_pci_resume, as they are already being done in the d3_resume op. Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eliad Peller 提交于
Allow the transport layer to return an error upon suspend. Signed-off-by: NEliad Peller <eliadx.peller@intel.com> Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eliad Peller 提交于
This reverts commit 088070a2. When working in d0i3_on_idle mode, we explicitly go out of d0i3 on resume (so other potential commands could be sent). However, D0I3_DEFER_WAKEUP is currently cleared on resume complete (which happens only later on), causing d0i3 exit to timeout. Since mac80211 was modified to accept incoming frames once drv_resume was called, we can safely revert this patch, and handle the pending work on iwl_mvm_resume(). Signed-off-by: NEliad Peller <eliadx.peller@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 03 6月, 2015 1 次提交
-
-
由 Eliad Peller 提交于
On resume, all the interrupts are masked (CSR_INT_MASK is 0), and ict is disabled. Re-configure them both. Signed-off-by: NEliad Peller <eliadx.peller@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 28 5月, 2015 3 次提交
-
-
由 Luciano Coelho 提交于
The regular and scheduled scan functions are very similar, so they can be combined into one. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
The iwl_mvm_scan_offload_stop() function is used to stop LMAC regular scan, stop LMAC scheduled scan and stop UMAC scheduled scans (but not UMAC regular scans), making it very difficult to read. Reorganize the scan stopping functions by creating separate functions to stop regular and scheduled scans, separating the LMAC stopping part of the code from the rest and renaming the offload_stop function to iwl_mvm_lmac_scan_stop(). Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
After the scan refactor, the order of the SSIDs passed to the firmware in all scans (including net-detect) are inverted. This was causing the reporting code to use the wrong SSIDs. To fix this, invert the array index when accessing the saved match SSIDs to report the wake-up. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 22 5月, 2015 3 次提交
-
-
由 Luciano Coelho 提交于
If the device is reset during suspend with net-detect enabled, we leave the net-detect information dangling and this causes the next suspend to fail with a warning: [21795.351010] WARNING: at /root/iwlwifi/iwlwifi-stack-dev/drivers/net/wireless/iwlwifi/mvm/d3.c:989 __iwl_mvm_suspend.isra.6+0x2be/0x460 [iwlmvm]() [21795.353253] Modules linked in: iwlmvm(O) iwlwifi(O) mac80211(O) cfg80211(O) compat(O) [...] [21795.366168] CPU: 1 PID: 3645 Comm: bash Tainted: G O 3.10.29-dev #1 [21795.368785] Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012 [21795.371441] f8ec6748 f8ec6748 e51f3ce8 c168aa62 e51f3d10 c103a824 c1871238 f8ec6748 [21795.374228] 000003dd f8eb982e f8eb982e 00000000 c3408ed4 c41edbbc e51f3d20 c103a862 [21795.377006] 00000009 00000000 e51f3da8 f8eb982e c41ee3dc 00000004 e7970000 e51f3d74 [21795.379792] Call Trace: [21795.382461] [<c168aa62>] dump_stack+0x16/0x18 [21795.385133] [<c103a824>] warn_slowpath_common+0x64/0x80 [21795.387803] [<f8eb982e>] ? __iwl_mvm_suspend.isra.6+0x2be/0x460 [iwlmvm] [21795.390485] [<f8eb982e>] ? __iwl_mvm_suspend.isra.6+0x2be/0x460 [iwlmvm] [21795.393124] [<c103a862>] warn_slowpath_null+0x22/0x30 [21795.395787] [<f8eb982e>] __iwl_mvm_suspend.isra.6+0x2be/0x460 [iwlmvm] [21795.398464] [<f8eb9d7c>] iwl_mvm_suspend+0xec/0x140 [iwlmvm] [21795.401127] [<c104be11>] ? del_timer_sync+0xa1/0xc0 [21795.403800] [<f8d4107e>] __ieee80211_suspend+0x1de/0xff0 [mac80211] [21795.406459] [<c168e43d>] ? mutex_lock_nested+0x25d/0x350 [21795.409084] [<c1586b64>] ? rtnl_lock+0x14/0x20 [21795.411685] [<f8cf0076>] ieee80211_suspend+0x16/0x20 [mac80211] [21795.414318] [<f8c4e014>] wiphy_suspend+0x74/0x710 [cfg80211] [21795.416916] [<c141e612>] __device_suspend+0x1e2/0x220 [21795.419521] [<f8c4dfa0>] ? addresses_show+0xa0/0xa0 [cfg80211] [21795.422097] [<c141f997>] dpm_suspend+0x67/0x210 [21795.424661] [<c141fd6f>] dpm_suspend_start+0x4f/0x60 [21795.427219] [<c108d8e0>] suspend_devices_and_enter+0x60/0x480 [21795.429768] [<c168646a>] ? printk+0x4d/0x4f [21795.432295] [<c108de76>] pm_suspend+0x176/0x210 [21795.434830] [<c108ca5d>] state_store+0x5d/0xb0 [21795.437410] [<c108ca00>] ? wakeup_count_show+0x50/0x50 [21795.439961] [<c13208db>] kobj_attr_store+0x1b/0x30 [21795.442514] [<c11e3a4b>] sysfs_write_file+0xab/0x100 [21795.445088] [<c11e39a0>] ? sysfs_poll+0xa0/0xa0 [21795.447659] [<c1179655>] vfs_write+0xa5/0x1c0 [21795.450212] [<c1179af7>] SyS_write+0x57/0xa0 [21795.452699] [<c1699ec1>] sysenter_do_call+0x12/0x32 [21795.455146] ---[ end trace faf5321baba2bfdb ]--- To fix this, call the iwl_mvm_free_nd() function in case of any error during resume. Additionally, rename the "out_unlock" label to err to make it clearer that it's only called in error conditions. Cc: stable@vger.kernel.org [3.19+] Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
The __iwl_mvm_resume() function always returns 1, which causes mac80211 to do a reconfig with IEEE80211_RECONFIG_TYPE_RESTART. This type of reconfig calls iwl_mvm_restart_complete(), where we unref the IWL_MVM_REF_UCODE_DOWN, so we should always take the reference in this case. This prevents this kind of warning from happening: [40026.103025] WARNING: at /root/iwlwifi/iwlwifi-stack-dev/drivers/net/wireless/iwlwifi/mvm/mac80211.c:236 iwl_mvm_unref+0xc9/0xd0 [iwlmvm]() [40026.105145] Modules linked in: iwlmvm(O) iwlwifi(O) mac80211(O) cfg80211(O) compat(O) ctr ccm arc4 autofs4 snd_hda_codec_hdmi snd_hda_codec_idt joydev coretemp kvm_intel kvm aesni_intel ablk_helper cryptd lrw aes_i586 snd_hda_intel xts snd_hda_codec gf128mul snd_hwdep snd_pcm snd_seq_midi dell_wmi snd_rawmidi sparse_keymap snd_seq_midi_event snd_seq uvcvideo dell_laptop videobuf2_core dcdbas microcode videodev psmouse snd_timer videobuf2_vmalloc videobuf2_memops serio_raw snd_seq_device btusb i915 snd bluetooth lpc_ich drm_kms_helper soundcore snd_page_alloc drm i2c_algo_bit wmi parport_pc ppdev video binfmt_misc rpcsec_gss_krb5 nfsd mac_hid nfs_acl nfsv4 auth_rpcgss nfs fscache lockd sunrpc msdos lp parport sdhci_pci sdhci ahci libahci e1000e mmc_core ptp pps_core [last unloaded: compat] [40026.117640] CPU: 2 PID: 3827 Comm: bash Tainted: G W O 3.10.29-dev #1 [40026.120216] Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012 [40026.122815] f8effd18 f8effd18 e740fd18 c168aa62 e740fd40 c103a824 c1871238 f8effd18 [40026.125527] 000000ec f8ec79c9 f8ec79c9 d5d29ba4 d5d2a20c 00000000 e740fd50 c103a862 [40026.128209] 00000009 00000000 e740fd7c f8ec79c9 f1c591c4 00000400 00000000 f8efb490 [40026.130886] Call Trace: [40026.133506] [<c168aa62>] dump_stack+0x16/0x18 [40026.136115] [<c103a824>] warn_slowpath_common+0x64/0x80 [40026.138727] [<f8ec79c9>] ? iwl_mvm_unref+0xc9/0xd0 [iwlmvm] [40026.141319] [<f8ec79c9>] ? iwl_mvm_unref+0xc9/0xd0 [iwlmvm] [40026.143881] [<c103a862>] warn_slowpath_null+0x22/0x30 [40026.146453] [<f8ec79c9>] iwl_mvm_unref+0xc9/0xd0 [iwlmvm] [40026.149030] [<f8ec7a4d>] iwl_mvm_mac_reconfig_complete+0x7d/0x210 [iwlmvm] [40026.151645] [<f8b74b20>] ? ftrace_raw_event_drv_reconfig_complete+0xc0/0xe0 [mac80211] [40026.154291] [<f8b6769e>] ieee80211_reconfig+0x28e/0x2620 [mac80211] [40026.156920] [<c10ef0ea>] ? ring_buffer_unlock_commit+0xba/0x100 [40026.159585] [<f8b4a04d>] ieee80211_resume+0x6d/0x80 [mac80211] [40026.162206] [<f8a79722>] wiphy_resume+0x72/0x260 [cfg80211] [40026.164799] [<c141e2e7>] ? device_resume+0x57/0x150 [40026.167425] [<f8a796b0>] ? wiphy_suspend+0x710/0x710 [cfg80211] [40026.170075] [<c141e26e>] dpm_run_callback+0x2e/0x50 [40026.172695] [<c141e321>] device_resume+0x91/0x150 [40026.175334] [<c141f636>] dpm_resume+0xf6/0x200 [40026.177922] [<c141f920>] dpm_resume_end+0x10/0x20 [40026.180489] [<c108d9f7>] suspend_devices_and_enter+0x177/0x480 [40026.183037] [<c168646a>] ? printk+0x4d/0x4f [40026.185559] [<c108de76>] pm_suspend+0x176/0x210 [40026.188065] [<c108ca5d>] state_store+0x5d/0xb0 [40026.190581] [<c108ca00>] ? wakeup_count_show+0x50/0x50 [40026.193052] [<c13208db>] kobj_attr_store+0x1b/0x30 [40026.195608] [<c11e3a4b>] sysfs_write_file+0xab/0x100 [40026.198055] [<c11e39a0>] ? sysfs_poll+0xa0/0xa0 [40026.200469] [<c1179655>] vfs_write+0xa5/0x1c0 [40026.202893] [<c1179af7>] SyS_write+0x57/0xa0 [40026.205245] [<c1699ec1>] sysenter_do_call+0x12/0x32 [40026.207619] ---[ end trace db1d5a72a0381b0a ]--- Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NEliadX Peller <eliad@wizery.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Haim Dreyfuss 提交于
fw_status is the only pointer pointing to a block of memory allocated above and should be freed after use. Note: this come from Klockwork static analyzer. Cc: stable@vger.kernel.org [3.19+] Fixes: 2021a89d ("iwlwifi: mvm: treat netdetect wake up separately") Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 29 4月, 2015 2 次提交
-
-
由 Luciano Coelho 提交于
Net-detect scans were using the same type as sched scan, which was causing the driver to return -EBUSY and prevent the system from suspending if there was an ongoing scheduled scan. To avoid this, add a new type for net-detect and don't stop anything when it is requested, so that the existing scheduled scan will be resumed when the system wakes up. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
All scans are using the unified APIs now, so using "unified" in the symbols is useless and just make them much longer and the main difference between scans now is LMAC vs. UMAC. Remove "unified" from all relevant symbols. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 28 4月, 2015 1 次提交
-
-
由 Emmanuel Grumbach 提交于
I forgot to rename the CPTCFG_ prefix... Fixes: 484b3d13 ("iwlwifi: mvm: add debugfs entry with the number of net-detect scans") Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 02 4月, 2015 1 次提交
-
-
由 Luciano Coelho 提交于
Our testers need to know the number of scans performed while in net-detect mode before the device wakes up. The firmware already passes this information to the driver, so we can save it and report it in a debugfs entry. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 19 3月, 2015 1 次提交
-
-
由 Eliad Peller 提交于
we unref IWL_MVM_REF_UCODE_DOWN on iwl_mvm_restart_complete(). Usually, the restart is initiated by iwl_mvm_nic_restart(), which takes the reference before restarting the hw. However, in D3 flow we might call ieee80211_restart_hw() directly (in case of suspend error and on d3_test-resume), which without taking the ref first. fix it. Signed-off-by: NEliad Peller <eliadx.peller@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 12 3月, 2015 3 次提交
-
-
由 Johannes Berg 提交于
The return value in iwl_mvm_get_wakeup_status() is a bit unclear in that it's not obvious that we don't leak fw_status in some cases. Use fw_status directly with ERR_PTR() and return only it, that way the compiler has a chance of proving that it's uninitialized (if it ever is due to new changes.) Additionally, this removes a smatch warning since smatch couldn't figure out that fw_status can't, in fact, leak here. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
When IWLWIFI_DEBUGFS is not set, we should not unlock the mutex after calling iwl_mvm_query_wakeup_reasons(), because this function unlocks it already. Move the goto out_iterate outside the #ifdef. Change-Id: I13d86402aecf0eeec44b1abbe2b244fbc706a5eb Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
-
由 Jonathan Doron 提交于
When moving to the D3 FW give it the valid MCC from the D0 FW. When returning from D3 to D0, query the D3 FW for the latest MCC, as it might have changed internally. This MCC will be replayed to the D0 FW when it boots. Signed-off-by: NJonathan Doron <jonathanx.doron@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 02 3月, 2015 1 次提交
-
-
由 Luciano Coelho 提交于
We shouldn't call iwl_mvm_d3_disconnect_iter() on the running interfaces when we are woken up due to net-detect, because it doesn't make sense. Additionally, this seems to set the IEEE80211_SDATA_DISCONNECT_RESUME flag that will cause a disconnection on the next resume (if a normal WoWLAN is used). To solve this, skip the iteration loop when net-detect is set. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reported-by: NSamuel Tan <samueltan@chromium.org> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 29 12月, 2014 3 次提交
-
-
由 Johannes Berg 提交于
A number of places (still) use a direct operation, use iwl_mvm_sta_from_mac80211() consistently. In one place also move it into the variable initializer. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eliad Peller 提交于
Enter d0i3 on suspend, and exit d0i3. Wait for the command responses in both cases. Use this mode in case of pcie trans. Signed-off-by: NEliad Peller <eliadx.peller@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eliad Peller 提交于
d3 and d0i3 shouldn't be mutually exclusive. Set supported wowlan triggers by looking for each of them, and check on suspend/resume which flow should be used ("any" trigger is supported by d0i3, and all the others by d3) Signed-off-by: NEliad Peller <eliadx.peller@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 01 12月, 2014 4 次提交
-
-
由 Luciano Coelho 提交于
Add the channels on which there was a match for every match reported by the firmware. The firmware reports the channels as indices to the array of channels that was passed in the scheduled scan request, so we need to save the array when entering D3 to make sure it is available when we resume. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Add SSID information to the net-detect indication to userspace. Fetch the matched profiles from the firmware in order to find the correct SSIDs in the profiles that matched. Since the net-detect information is stored in cfg80211, and in theory it could change while we are waking up and reading the matched profiles, we need to save it when we enter D3 so it is available during resume. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
All the supported firmwares have this TLV flag set. Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Query the firmware for scan offload matches when waking up in order to report net detect as the reason for the wake up. This requires a new command API to be implemented. Additionally, remove some net detect command entries that are not valid anymore. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 24 11月, 2014 7 次提交
-
-
由 Eliad Peller 提交于
call the appropriate iwl_trans_suspend/resume ops on iwl_mvm_suspend/resume calls. Signed-off-by: NEliad Peller <eliadx.peller@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
When the device wakes up due to netdetect, we need to query different things from the firmware than when it wakes up with a normal WoWLAN. To make this easier, separate the netdetect wake up handling from the rest. For now, we don't send netdetect as a wake up reason, treating it as a non-wireless wake up. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Refactor the iwl_mvm_query_wakeup_reasons() function to split the part that gets the firmware status from the part that sets up the WoWLAN status. This will allow netdetect to reuse the code. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
We need to send a WOWLAN_CONFIGURATION command also for netdetect and configure the rfkill release trigger if needed. To do so, refactor the code that configures wowlan and netdetect when suspending and send the WOWLAN_CONFIGURATION command also for net_detect. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Add the net detect WoWLAN flag to indicate support and use the nd_config from the WoWLAN configuration to start net detect, if it is set. The WoWLAN configuration takes precedence over the debugfs configuration. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Instead of allocating nd_ies separately, make it part of the iwl_mvm structure so it's easier to handle its lifetime. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eliad Peller 提交于
The deferred d0i3 exit is currently implemented in the resume op, which is called when mac80211 starts its resume process. However, mac80211 still doesn't handle frames at this stage, which results in frames being dropped. Move the deferred d0i3 handling to the reconfig_complete callback, in order to make sure mac80211 is fully available at this point. Signed-off-by: NEliad Peller <eliadx.peller@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 11 11月, 2014 1 次提交
-
-
由 Johannes Berg 提交于
The code to capture firmware errors works during the reconfiguration phase after an error. As the D3->D0 transition uses the same flow to get the D0 image reconfigured, this triggered and caused a firmware coredump to be collected. This in turn, if it isn't picked up by userspace, can cause module unloading to fail, which is how the bug was detected. To fix this issue, introduce a new status flag (D3_RECONFIG) and use it to detect that during reconfiguration no coredump should be taken and reported. Reported-by: NAvi Kraif <avix.kraif@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 29 10月, 2014 5 次提交
-
-
由 Luciano Coelho 提交于
Getting the BSS station vif is something that may be needed by other parts of the code. So, instead of having an iterator specifically for d3, change it into a generic one in utils.c. Additionally, add a iwl_mvm_get_bss_vif() function to make it easier to retrieving it. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Before we get all the chain (ie. mac80211, cfg80211, nl80211 and userspace) changed to support net-detect, we can use this debugfs entry for easy testing and as a proof of concept. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Instead of checking if we are associated when suspending with wowlan enabled in the interface iterator, allow it to return an unassociated vif and move the check to the main suspend function. This will be needed by netdetect, since it should also work when we are not associated but the vif is active. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
Take the WoWLAN handling code out of the main suspend function, dividing it into three parts: get_config (which is used before the firmware is switched), switch_to_d3 (which handles the rebooting of the hardware with the D3 firmware) and config (which configures the D3 firmware for WoWLAN operation). This is necessary to prepare for the net-detect implementation, which will use only the switch_to_d3 part of this flow. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
We use ieee80211_iter_keys() which requires the rtnl to be held. If we don't lock the rtnl, like we do when we suspend during a d3 test, we get the following splat: RTNL: assertion failed at net/mac80211/key.c (566) CPU: 1 PID: 26529 Comm: cat Tainted: G W O 3.10.29-dev #1 Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012 e7b15008 e7b15008 e68adc1c c168aa62 e68adc54 f91f20b6 f923700c f9236fd8 00000236 00000000 ece23874 00000000 f94941e0 00000000 e43b8e48 e7b15008 00000000 e8b69e78 e68adcc0 f9493ab9 e68adc68 00000000 e43b8e48 e7b15008 Call Trace: [<c168aa62>] dump_stack+0x16/0x18 [<f91f20b6>] ieee80211_iter_keys+0x166/0x170 [mac80211] [<f94941e0>] ? iwl_mvm_query_wakeup_reasons+0x5f0/0x5f0 [iwlmvm] [<f9493ab9>] iwl_mvm_setup_connection_keep.isra.5+0x99/0x1d0 [iwlmvm] [<f9165e28>] ? cfg80211_report_wowlan_wakeup+0x308/0x510 [cfg80211] [<f9493fe5>] iwl_mvm_query_wakeup_reasons+0x3f5/0x5f0 [iwlmvm] [<c116125a>] ? init_object+0x3a/0x70 [<f8a5b8ee>] ? iwl_trans_pcie_d3_resume+0x1be/0x3a0 [iwlwifi] [<f94956da>] __iwl_mvm_resume+0x14a/0x180 [iwlmvm] [<f9495736>] iwl_mvm_d3_test_release+0x26/0xc0 [iwlmvm] [<c117a64d>] __fput+0xad/0x210 [<c117a7bd>] ____fput+0xd/0x10 [<c10601a1>] task_work_run+0x81/0xb0 [<c1040fa5>] do_exit+0x255/0xac0 [<c104e511>] ? dequeue_signal+0x31/0x1a0 [<c1041888>] do_group_exit+0x38/0xa0 [<c10a6cfb>] ? trace_hardirqs_on+0xb/0x10 [<c1051c31>] get_signal_to_deliver+0x1e1/0x8e0 [<c104bd52>] ? try_to_del_timer_sync+0x42/0x60 [<c104bd70>] ? try_to_del_timer_sync+0x60/0x60 [<c168dc82>] ? schedule_timeout+0x102/0x2a0 [<c10011ba>] do_signal+0x3a/0x8e0 [<c104b190>] ? __internal_add_timer+0xb0/0xb0 [<c168de7a>] ? schedule_timeout_interruptible+0x1a/0x20 [<c104ce39>] ? msleep_interruptible+0x39/0x40 [<f94939a9>] ? iwl_mvm_d3_test_read+0x49/0x70 [iwlmvm] [<c11797fc>] ? vfs_read+0x8c/0x160 [<c11243af>] ? SyS_fadvise64_64+0x15f/0x2b0 [<f9493960>] ? iwl_mvm_wowlan_program_keys+0x4a0/0x4a0 [iwlmvm] [<c1179a57>] ? SyS_read+0x57/0xa0 [<c1001acf>] do_notify_resume+0x6f/0xa0 [<c1692500>] work_notifysig+0x29/0x31 Fix this by hold the rtnl lock when calling __iwl_mvm_resume() in the d3 test wake up path. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 04 9月, 2014 1 次提交
-
-
由 Johannes Berg 提交于
The firmware would like to have a MAC context (unassoc) before the AP station is removed (we do this) but would like to keep the BSSID until after it is removed, so we need to send two commands - one with the BSSID before and one without the BSSID after. In order to do this, we need to store the BSSID as it will have been cleared by mac80211 by the time we get notified of the disassociation. Also pass it around as an override to the various functions needing it, and keep taking it from the mac80211 data otherwise. This avoids having to keep track of the BSSID in all modes. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-