U2D Controller of pxa3xx is able to work in host mode.
Make pxa specific ohci implementation aware of it.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Reported-by: NChristian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some ohci-pxa27x platforms may require OCPM and NOCP in UHCRHDA to be
clear, but the existing code was only allowing setting.  This patch
ensures that these bits are clear if the respective flags are not set.
This is particularly important for the PXA3xx family where the
documentation says OCPM must be cleared, but it is set after reset.
Signed-off-by: NAric Blumer <aric@sdgsystems.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On resume, the power-related bits in UHCRHDA were not being set, so
they would default to the reset state.  For PXA3xx devices, OCPM must
be cleared, but it was remaining set from resume reset.
Signed-off-by: NAric D. Blumer <aric@sdgsystems.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Where devices only have one consumer, passing a consumer clock ID
has no real benefit.  Remove it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This avoid the pre-mapping of OHCI controller register space, and the
mapping is made only when necessary (OHCI is probed).
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Direct access to pxa27x specific register PSSR in a generic ohci driver
is no good, introduce pxa27x_clear_otgph() and move the implementation
into processor specific code.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Depending on the order of how resource is defined in the platform
device is not good, use platform_get_{irq,resource} for the IRQ
and memory resources.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Direct access to USB host controller registers is considered to be not
portable, and is usually a bad sign for poorly abstracted interface.
Introduce .flags and .power_on_delay to "struct pxaohci_platform_data"
so that most platforms don't bother to write their own .init/.exit()
sequences.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch (as1069c) changes the way OHCI root-hub status-change
interrupts are enabled.  Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub.  This approach turns out to be subject to races, resulting
in unnecessary polling.

The patch does away with the method entirely.  Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present.  This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file.  Remove these unnecessary
includes.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This reverts commit e8721549.

Andrey Borzenkov reports that it resulted in a totally hung machine for
him when loading the OHCI driver.  Extensive netconsole capture with
SysRq output shows that modprobe gets stuck in ohci_hub_status_data()
when probing and enabling the OHCI controller, see for example

	http://lkml.org/lkml/2008/7/5/236

for an analysis.

The problem appears to be an interrupt flood triggered by the commit
that gets reverted, and Andrey confirmed that the revert makes things
work for him again.
Reported-and-tested-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

and include pxa2xx-regs.h as build fix since PSSR definitions
moved from pxa-regs.h into pxa2xx-regs.h.

Note: This change is temporary as pxa27x processor specific
code will be finally moved elsewhere (both drivers should
support pxa3xx, too).
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch (as1069b) changes the way OHCI root-hub status-change
interrupts are enabled.  Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub.  This approach turns out to be subject to races, resulting
in unnecessary polling.

The patch does away with the method entirely.  Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present.  This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Drivers in the ohci-hcd family should perform certain tasks whenever
their controller device is resumed.  These include checking for loss
of power during suspend, turning on port power, and enabling interrupt
requests.

Until now these jobs have been carried out when the root hub is
resumed, not when the controller is.  Many drivers work around the
resulting awkwardness by automatically resuming their root hub
whenever the controller is resumed.  But this is wasteful and
unnecessary.

To simplify the situation, this patch (as1066) adds a new core
routine, ohci_finish_controller_resume(), which can be used by all the
OHCI-variant drivers.  They can call the new routine instead of
resuming their root hubs.  And ohci-pci.c can call it instead of using
its own special-purpose handler.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

power.power_state is scheduled for removal.  This patch (as1053)
removes all uses of that field from drivers/usb.  Almost all of them
were write-only, the most significant exceptions being sl811-hcd.c and
u132-hcd.c.

Part of this patch was written by Pavel Machek.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable USB HCDs,
to allow re-enable auto loading.

[dbrownell@users.sourceforge.net: more drivers; registration fixes]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that

	CKEN0_PWM0 --> CKEN_PWM0
	CKEN1_PWM1 --> CKEN_PWM1
	...
	CKEN24_CAMERA --> CKEN_CAMERA

The reasons for the change of these defitions are:

1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24

2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for

3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off

Another change in the patch is to make the definitions equal to its
clock bit index, so that

   #define CKEN_CAMERA  (24)

instead of

   #define CKEN_CAMERA  (1 << 24)

this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: Neric miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The previous model had the module_init & module_exit function in the
bus glue .c files themselves. That's a problem if several glues need
to be selected at once and the driver is built has module. This case
is quite common in embedded system where you want to handle both the
integrated ohci controller and some extra controller on PCI.

The ohci-hcd.c file now provide the module_init & module_exit and
appropriate driver registering/unregistering is done conditionally,
using #ifdefs.
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is an OHCI cleanup patch ... it removes a lot of erroneous whitespace
(space before tab, at end of line) as well as the obsolete inline changelog.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If some problem occurs during ehci startup, for instance, request_irq fails,
echi hcd driver tries it best to cleanup, but fails to unregister reboot
notifier, which in turn leads to crash on reboot/poweroff.

The following patch resolves this problem by not using reboot notifiers
anymore, but instead making ehci/ohci driver get its own shutdown method.  For
PCI, it is done through pci glue, for everything else through platform driver
glue.

One downside: sa1111 does not use platform driver stuff, and does not have its
own shutdown hook, so no 'shutdown' is called for it now.  I'm not sure if it
is really necessary on that platform, though.
Signed-off-by: NAleks Gorelov <dared1st@yahoo.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This teaches OHCI to use the root hub status change (RHSC) IRQ, bypassing
root hub timers most of the time and switching over to the "new" root hub
polling scheme.  It's complicated by the fact that implementations of OHCI
trigger and ack that IRQ differently (the spec is vague there).

Avoiding root hub timers helps mechanisms like "dynamic tick" leave the
CPU in lowpower modes for longer intervals.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch from Richard Purdie

Add a power budget variable to the PXA OHCI platform data and add a
default value for the spitz platform(s) which prevents known failures
with certain USB devices.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The device data in ohci-pxa27x is a struct hcd, not a struct ohci_hcd.
This correct the suspend/resume calls to account for this and adds some
code to invalidate the platform data when the module is removed.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add power management functions for the pxa27x USB OHCI host controller.
This is a totally rewritten version of the patch by Nicolas Pitre and
Todd Poynor which accounts for recent USB changes.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.

This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NNicolas Pitre <nico@cam.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.

In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch.  This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other.  So if any
hunk rejects or gets in the way of other patches, just drop it.  My scripts
will pick it up again in the next round.
Signed-off-by: NTim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as580) is perhaps the only result from the long discussion I
had with David about his changes to the root-hub suspend/resume code.  It
renames the hub_suspend and hub_resume methods in struct usb_hcd to
bus_suspend and bus_resume.  These are more descriptive names, since the
methods really do suspend or resume an entire USB bus, and less likely to
be confused with the hub_suspend and hub_resume routines in hub.c.

It also takes David's advice about removing the layer of bus glue, where
those methods are called.  And it implements a related change that David
made to the other HCDs but forgot to put into dummy_hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This cleans up a small recent FIXME, ensuring that all the HCDs provide
root hub suspend/resume methods.  It also wraps the calls to those root
suspend routines just like on the PCI "USB_SUSPEND not defined" cases,
so non-PCI bus glue won't be as tempted to behave very differently.

Several of the SOC based OHCI drivers forgot to list those methods;
the patch also adds those missing declarations.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hcd.c          |   42 +++++++++++++++++++++++++---------------
 drivers/usb/host/ohci-au1xxx.c  |    5 ++++
 drivers/usb/host/ohci-lh7a404.c |    5 ++++
 drivers/usb/host/ohci-pxa27x.c  |    1
 drivers/usb/host/ohci-s3c2410.c |    1
 drivers/usb/host/ohci-sa1111.c  |    1
 6 files changed, 40 insertions(+), 15 deletions(-)

This simplifies some of the PM-related #ifdeffing by recognizing
that USB_SUSPEND depends on PM.  Also, OHCI drivers were often
testing for USB_SUSPEND when they should have tested just PM.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hcd.c          |    2 ++
 drivers/usb/host/ohci-hcd.c     |    2 +-
 drivers/usb/host/ohci-hub.c     |    4 ++--
 drivers/usb/host/ohci-omap.c    |    2 +-
 drivers/usb/host/ohci-pci.c     |    2 +-
 drivers/usb/host/ohci-ppc-soc.c |    4 ++--
 drivers/usb/host/ohci-pxa27x.c  |    2 +-
 drivers/usb/host/ohci-s3c2410.c |    3 +--
 drivers/usb/host/ohci-sa1111.c  |    2 +-
 9 files changed, 12 insertions(+), 11 deletions(-)

In PM v1, all devices were called at SUSPEND_DISABLE level.  Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level.  However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.

Since this is obsolete infrastructure which is no longer necessary,
we can remove it.  Here's an (untested) patch to do exactly that.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>