Remove the regulator enable while driver loading and enable it only when
the cable/device is connected and disable it when disconnected.

Remove the configuration of config_state and config_trans register
configuration as these registers are programmed when regulator
enable/disable is called.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Calling runtime pm APIs pm_runtime_put_sync() and pm_runtime_get_sync()
for enabling/disabling the clocks, sysconfig settings.

Enable clock, configure no-idle/standby when active and configure force idle/standby
and disable clock when idled. This is taken care by the runtime framework when
driver calls the pm_runtime_get_sync and pm_runtime_put_sync APIs.
Need to configure MUSB into force standby and force idle mode when usb not used
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

struct usb_request's list_head is supposed to be
used only by gadget drivers, but musb is abusing
that. Give struct musb_request its own list_head
and prevent musb from poking into other driver's
business.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Just a few cosmetic fixes to usb_gadget_probe_driver()
and usb_gadget_unregister_driver().

Decreased a few indentation levels with goto statements.

While at that, also add the missing call to musb_stop().
If we don't have OTG, there's no point of leaving
MUSB prepared for operation if a gadget driver fails
to probe. The same is valid for usb_gadget_unregister_driver(),
since we are removing the gadget driver and we don't have
OTG, we can completely unconfigure MUSB.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During development, even though board is wired
to e.g. OTG, we might want to compile host-only
or peripheral-only configurations.

Let's allow that to happen.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use bitmap_set()/bitmap_clear() to fill/zero a region of a bitmap
instead of doing set_bit()/clear_bit() each bit.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that ehci_run don't call ehci_reset, we can use ehci_run.
Signed-off-by: NMatthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

TDI driver does the ehci_reset in their reset callback.
Don't reset in ehci_run because configuration settings done in
platform driver will be reset.

This will allow to make msm use ehci_run.
Signed-off-by: NMatthieu CASTET <castet.matthieu@parrot.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver private data is retrieved incorrectly which results
a crash when written into "mode" debugfs file.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below compiler warning

drivers/usb/otg/msm72k_otg.c:257: warning: 'msm_otg_suspend' defined but not used
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add const modifier before global variable realtek_cr_ids.
Signed-off-by: Nwwang <wei_wang@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix some sparse warning for realtek_cr patch
Signed-off-by: Nwwang <wei_wang@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

resumption of devices can fail. Errors must be handled.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The device never needs to be resumed in close(). But the counters
must be balanced. As resumption can fail, but the counters must
be balanced, use the _no_resume() version which cannot fail.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If an error happens during resumption.
The remaining data has to be cleanly discarded and the pm
counters have to be adjusted.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As soon as the first error happens, the write must
be stopped, lest we send mutilated messages.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

An error in the write code path would permanently disable
runtime PM in this driver
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes two errors:
- the device is busy if a message was recieved even if resubmission fails
- the device is not busy if resubmission fails due to -EPERM
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In function at91udc_probe()
call put_device() when device_register() fails.
Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The document says:
|2.1 Problem description
|    When at least two USB devices are simultaneously running, it is observed that
|    sometimes the INT corresponding to one of the USB devices stops occurring. This may
|    be observed sometimes with USB-to-serial or USB-to-network devices.
|    The problem is not noticed when only USB mass storage devices are running.
|2.2 Implication
|    This issue is because of the clearing of the respective Done Map bit on reading the ATL
|    PTD Done Map register when an INT is generated by another PTD completion, but is not
|    found set on that read access. In this situation, the respective Done Map bit will remain
|    reset and no further INT will be asserted so the data transfer corresponding to that USB
|    device will stop.
|2.3 Workaround
|    An SOF INT can be used instead of an ATL INT with polling on Done bits. A time-out can
|    be implemented and if a certain Done bit is never set, verification of the PTD completion
|    can be done by reading PTD contents (valid bit).
|    This is a proven workaround implemented in software.

Russell King run into this with an USB-to-serial converter. This patch
implements his suggestion to enable the high frequent SOF interrupt only
at the time we have ATL packages queued. It goes even one step further
and enables the SOF interrupt only if we have more than one ATL packet
queued at the same time.

Cc: <stable@kernel.org> # [2.6.35.x, 2.6.36.x, 2.6.37.x]
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

ehci_lpm_set_da and ehci_lpm_check are EHCI 1.1 specific functions which
are not used on many platforms but do generate annoying gcc warnings
Signed-off-by: NMaksim Rayskiy <mrayskiy@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We need FUSB300_MAX_NUM_EP (16) names otherwise the last 8 names get
initialized to garbage values in fusb300_probe().
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a patch that seems to make the USB hangs on the S3C244X go away.
At least a good amount of ping torture didn't make them come back so far.

The issue is that, if there are several back-to-back packets, sometimes no
interrupt is generated for one of them. This seems to be caused by the
mysterious dual packet mode, which the USB hardware enters automatically
if the endpoint size is half that of the FIFO. (On the 244X, this is the
normal situation for bulk data endpoints.)

There is also a timing factor in this. It seems that what happens is that
the USB hardware automatically sends an acknowledgement if there is only one
packet in the FIFO (the FIFO has space for two). If another packet arrives
before the host has retrieved and acknowledged the previous one, no interrupt
is generated for that second one.

However, there may be an indication. There is one undocumented bit (none
of the 244x manuals document it), OUT_CRS1_REG[1], that seems to be set
suspiciously often when this condition occurs. There is also
CLR_DATA_TOGGLE, OUT_CRS1_REG[7], which may have a function related to
this. (The Samsung manual is rather terse on that, as usual.)

This needs to be examined further. For now, the patch seems to do the
trick.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This PCH_UDC driver does not work normally when "Ethernet gadget" is used.

This patch fixed this issue.
The following was modified.
 - The FIFO flush process.
 - The descriptor creation process.
 - The adjustment of DMA buffer align.

Currently the PCH_UDC driver can work normally with "Ethernet gadget",
"Serial gadget" or "File-backed Storage Gadget".
Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Build USB tools easier.
Signed-off-by: NDavidlohr Bueso <dave@gnu.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reorder the driver->name assignment so the 'iProduct' could be initialized
as well if both 'name' and 'iProduct' come as NULL by default.

Also, remove the misplaced 'extern' keyword.
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While checking valid interface number we should compare MAX_CONFIG_INTERFACES
with the variable 'intf' (which holds the lower 8bits of w_index) rather than
'w_index'
Signed-off-by: NJassi Brar <jassi.brar@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit b7d5b439.
It conflicts with commit baab93af "USB:
EHCI: ASPM quirk of ISOC on AMD Hudson" and merging the two just doesn't
work properly.

Cc: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: set flow handler for secondary interrupt controller of 5249
  m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
  m68knommu: fix dereference of port.tty
  m68knommu: add missing linker __modver section
  m68knommu: fix mis-named variable int set_irq_chip loop
  m68knommu: add optimize memmove() function
  m68k: remove arch specific non-optimized memcmp()
  m68knommu: fix use of un-defined _TIF_WORK_MASK
  m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
  m68knommu: fix m548x_wdt.c compilation after headers renaming
  m68knommu: Remove dependencies on nonexistent M68KNOMMU

The secondary interrupt controller of the ColdFire 5249 code is not
setting the edge triggered flow handler. Set it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The m68knommu arch does not define or use IRQ_FLG_LOCK in its irq
subsystem. Remove obsolete use of it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Add missing linker section __modver to fix:

  LD      vmlinux
/usr/local/bin/../m68k-uclinux/bin/ld.real: error: no memory region specified for loadable section `__modver'
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Compiling for 68360 targets gives:

  CC      arch/m68knommu/platform/68360/ints.o
arch/m68knommu/platform/68360/ints.c: In function ‘init_IRQ’:
arch/m68knommu/platform/68360/ints.c:135:16: error: ‘irq’ undeclared (first use in this function)
arch/m68knommu/platform/68360/ints.c:135:16: note: each undeclared identifier is reported only once for each function it appears in

Fix variable name used.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Add an m68k/coldfire optimized memmove() function for the m68knommu arch.
This is the same function as used by m68k. Simple speed tests show this
is faster once buffers are larger than 4 bytes, and significantly faster
on much larger buffers (4 times faster above about 100 bytes).

This also goes part of the way to fixing a regression caused by commit
ea61bc46 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memmove() fucntion
defined, since there was none in the m68knommu/lib functions.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The m68k arch implements its own memcmp() function. It is not optimized
in any way (it is the most strait forward coding of memcmp you can get).
Remove it and use the kernels standard memcmp() implementation.

This also goes part of the way to fixing a regression caused by commit
ea61bc46 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memcmp() function
defined, since there is none in the m68knommu/lib functions.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
  drm/radeon/kms: hopefully fix pll issues for real (v3)
  drm/radeon/kms: add bounds checking to avivo pll algo
  drm: fix wrong usages of drm_device in DRM Developer's Guide
  drm/radeon/kms: fix a few more atombios endian issues
  drm/radeon/kms: improve 6xx/7xx CS error output
  drm/radeon/kms: check AA resolve registers on r300
  drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
  drm/radeon/kms: use linear aligned for evergreen/ni bo blits
  drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
  drm/radeon: fix race between GPU reset and TTM delayed delete thread.
  drm/radeon/kms: evergreen/ni big endian fixes (v2)
  drm/radeon/kms: 6xx/7xx big endian fixes
  drm/radeon/kms: atombios big endian fixes
  drm/radeon: 6xx/7xx non-kms endian fixes
  drm/radeon/kms: optimize CS state checking for r100->r500
  drm: do not leak kernel addresses via /proc/dri/*/vma
  drm/radeon/kms: add connector table for mac g5 9600
  radeon mkregtable: Add missing fclose() calls
  drm/radeon/kms: fix interlaced modes on dce4+
  drm/radeon: fix memory debugging since d961db75
  ...