All chips of i.mx6 can be powered off by programming SNVS.
For example :
On i.mx6q-sabresd board, PMIC_ON_REQ connect with external
pmic ON/OFF pin, that will cause the whole PMIC powered off
except VSNVS. And system can restart once PMIC_ON_REQ goes
high by push POWRER key.
Signed-off-by: NRobin Gong <b38343@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds links to the on-chip SRAM and reset controller nodes
and switches the interrupts. Make the BIT processor interrupt, which exists on
all variants, the first one. The JPEG unit interrupt, which does not exist on
i.MX27 and i.MX5 thus is an optional second interrupt.
Use different compatible strings for i.MX6Q/D and i.MX6S/DL, as they have to
load separate firmware images for some reason.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Original gpt per clk parent is from ipg_per clk which
may be scaled when system enter low bus mode, as ipg
clk will be lower in low bus mode, to keep system clk
NOT drift, select gpt per clk parent from OSC which
is at fixed freq always.

On i.mx6qdl, add a osc_per clk source for i.mx6q
TO > 1.0 and all i.MX6dl SoC.

On i.mx6sx, just make gpt per clk from OSC.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Baud clock is used for bit clock generation in master mode. Ipg clock
is peripheral clock and peripheral access clock.
Signed-off-by: NShengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Fixes "imx6q-pcie 1ffc000.pcie: missing *config* reg space"
error exposed by new versions of the designware pcie driver.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds simple-card support to the i.MX SoCs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Since commit 98ea6ad2 (ARM: dts: imx6: use imx51-ssi) the mx6 ssi is
compatible with imx51, so align all the mx6 variant ssi compatible strings as:

compatible = "fsl,<imx6-soc>-ssi", "fsl,imx51-ssi";
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

When booting a board that does not have a keypad (such as imx6q-sabresd) the
following error is seen on boot:

imx-keypad 20b8000.kpp: OF: linux,keymap property not defined in /soc/aips-bus@02000000/kpp@020b8000
imx-keypad 20b8000.kpp: failed to build keymap
imx-keypad: probe of 20b8000.kpp failed with error -2

Let's disable the keypad functionality in the dtsi files and let each board dts
enable it when needed.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Switch to use DT macro for clock ID, so that device tree source is more
readable.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

All dtsi files where already moved to generic dma bindings. Remove the
old non-generic DMA properties.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The S/PDIF rxtx4 and rxtx6 clock inputs are "ESAI_HCKT" and "MLB clock",
respectively, according to the SoC documentation, and they are currently
mapped to clocks "esai" and "mlb".

However, they do not seem to actually work correctly. Testing on a
Cubox-i system with fsl_spdif driver forced to select one of those as
input will result in I/O errors on audio playback, which I believe means
missing clock signal.

Possibly the "ESAI_HCKT" and "MLB clock" refer to some other clocks
related to ESAI and MLB, or we are missing something else.

Since audio playback will not work if fsl_spdif selects these clocks
(which happens rarely), set the inputs do dummy clocks, at least for
now.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The rxtx2 clock of i.MX6 S/PDIF is currently set to "asrc" clock.
However, according to SoC documentation, rxtx2 is connected to
ASRC_EXT_CLK, a different external clock.

Testing on Cubox-i system seems to confirm that: when fsl_spdif is
forced to select rxtx2 as input clock, audio playback fails with an I/O
error.

Set rxtx2 to the dummy clock by default to prevent fsl_spdif from
selecting it.
Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds CSI subnodes for IPU1 and IPU2 that will contain
ports and endpoints connecting to external elements in the video
pipeline.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The new bindings drops one clock, renames the others and
drops the old interrupt mapping.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add alias for FEC ethernet on i.MX to allow bootloaders (like U-Boot)
patch-in the MAC address for FEC using this alias.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Per bindings of fixed-clock, #clock-cells is a required property.  Let's
add it for those fixed rate clocks.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Those two properties should have been set to zero, which
is the same as not specifying them.

Having address-cells set to 1 causes OF interrupt
mapping routines to add 1 to the interrupt-cells
property and as result fail because all calculations
are off by one.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

As defined by the common PCI bindings.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch connects IPU and display encoder (HDMI, LVDS, MIPI)
device tree nodes, as well as parallel displays on the DISP0
and DISP1 outputs, using the OF graph bindings described in
Documentation/devicetree/bindings/media/video-interfaces.txt

The IPU ports correspond to the two display interfaces. The
order of endpoints in the ports is arbitrary.

Each encoder with an associated input multiplexer has multiple
input ports in the device tree. The order and reg property of
the ports must correspond to the multiplexer input order.

Since the imx-drm node now only needs to contain links to the
display interfaces, it can be moved to the SoC dtsi level. At
the board level, only connections between the display interface
ports and encoders or panels have to be added.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Extracted from another patch by Fabio Estevam, this adds the DT
configuration for HDMI output on the IMX6 SoCs
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

imx51-ssi and imx21-ssi are different IPs. imx51-ssi supports online
reconfiguration and needs this for correct interaction with SDMA. This
patch adds imx51-ssi before each imx21-ssi for all imx6 SoCs.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Enable dma support for espci controller
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

We need to use controller id to access different register regions
for mxs phy.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add anatop phandle for usbphy
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

We need to be able to override interrupts in board file to
workaround a hardware bug for ethernet interrupts
waking the processor by using interrupts-extended.
So, use interrupts-extended here as well.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Instead of calling the regulator for the ARM core as 'cpu', let's rename it
as 'vddarm', so that we keep a better consistency with the other internal
regulators:

vdd1p1: 800 <--> 1375 mV at 1100 mV
vdd3p0: 2800 <--> 3150 mV at 3000 mV
vdd2p5: 2000 <--> 2750 mV at 2400 mV
vddarm: 725 <--> 1450 mV at 1150 mV
vddpu: 725 <--> 1450 mV at 1150 mV
vddsoc: 725 <--> 1450 mV at 1200 mV
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Thermal sensor needs pll3_usb_otg when measuring temperature,
so we need to pass clk info to thermal driver.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Make the interrupts node slightly more readable.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

We will reference mipi_csi from board
dts files.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts.  However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected.  This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board.  It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.

The patch moves all the pinctrl data into individual boards as needed.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral.  Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Typically nodes are disabled by default and enabled when needed.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This reverts commit b1d27c79.

Previously we switched the SSI scriprt to dual-fifo mode to reduce playback
underrun issue, which is only included by SDMA firmware version 2. However,
there are quite a lot people still using version 1 or default firmware in
the ROM code of SoC while these two kinds of firmwares do not support the
dual-fifo script and the audio function on their platform would be broken.

Thus this patch provisionally reverts the dual-fifo script to the original
single fifo script to meet all kinds of users' requirements, including the
version 1/2 or inner ROM firmware.
Reported-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Use dual-fifo sdma scripts instead of shared scripts for ssi on i.MX series.
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The spdif "rxtx5" clock option is being set to ipg clk (62) by mistake.
This causes an incorrect time keeping when spdif driver is running,
because ipg is ancestor clock for clocksource while spdif driver will
change the rate of this clock in certain circumstance.  Before the
correct clock for "rxtx5" option can be supplied, let's disable this
option for now by filling a dummy clock for it.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add pcie device node for imx6qdl.
Signed-off-by: NSean Cross <xobs@kosagi.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This is needed for supporting ultra high speed cards like SD3.0 cards.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>