- 18 6月, 2019 2 次提交
-
-
由 Arnd Bergmann 提交于
Platforms should not normally select all the device drivers, leave that up to the user and the defconfig file. In this case, we get a warning for randconfig builds: WARNING: unmet direct dependencies detected for SERIAL_OF_PLATFORM Depends on [n]: TTY [=y] && HAS_IOMEM [=y] && SERIAL_8250 [=n] && OF [=y] Selected by [y]: - MACH_IXP4XX_OF [=y] && ARCH_IXP4XX [=y] Fixes: 9540724c ("ARM: ixp4xx: Add device tree boot support") Signed-off-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Arnd Bergmann 提交于
The "+sec" extension is invalid for older ARM architectures, but the code can now be built on any ARM configuration: /tmp/trusted_foundations-2d0882.s: Assembler messages: /tmp/trusted_foundations-2d0882.s:194: Error: architectural extension `sec' is not allowed for the current base architecture /tmp/trusted_foundations-2d0882.s:201: Error: selected processor does not support `smc #0' in ARM mode /tmp/trusted_foundations-2d0882.s:213: Error: architectural extension `sec' is not allowed for the current base architecture /tmp/trusted_foundations-2d0882.s:220: Error: selected processor does not support `smc #0' in ARM mode Add a dependency on ARMv7 for the build. Fixes: 4cb5d9ec ("firmware: Move Trusted Foundations support") Signed-off-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
- 17 6月, 2019 14 次提交
-
-
由 Andy Gross 提交于
This patch updates the Qualcomm SoC repo to a new location. Signed-off-by: NAndy Gross <agross@kernel.org> Reviewed-by: NBjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Olof Johansson 提交于
Merge tag 'omap-for-v5.2/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes Fixes for omap variants Three fixes mostly for dra7 SoC variants that have some devices disabled compared to the base SoC. These got broken by the change of making devices probe with ti-sysc interconnect target module and went unnnoticed for a while. And there is no clkcel bit for timer12 unlike timer1. Also included is a GPIO direction fix for phytec SDIO card detection. * tag 'omap-for-v5.2/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: am335x phytec boards: Fix cd-gpios active level ARM: dts: dra72x: Disable usb4_tm target module ARM: dts: Drop bogus CLKSEL for timer12 on dra7 Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Olof Johansson 提交于
Merge tag 'davinci-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes DaVinci fixes for v5.2 kernel. This addresses an issue with probe of IO expander on DA850 EVM. There is also a WARN_ON() fix on DA850 and DA830 devices. * tag 'davinci-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: ARM: davinci: da8xx: specify dma_coherent_mask for lcdc ARM: davinci: da850-evm: call regulator_has_full_constraints() Signed-off-by: NOlof Johansson <olof@lixom.net>
-
git://git.infradead.org/linux-mvebu由 Olof Johansson 提交于
mvebu fixes for 5.2 (part 1) Fixing defconfig allowing to use Ethernet again on Armada 38x based boards * tag 'mvebu-fixes-5.2-1' of git://git.infradead.org/linux-mvebu: ARM: mvebu_v7_defconfig: fix Ethernet on Clearfog Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Olof Johansson 提交于
Merge tag 'am654-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into fixes Texas Instruments AM65x fixes for v5.2 - Fix up a Kbuild warning when SOC_TI is not set * tag 'am654-fixes-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux: arm64: arch_k3: Fix kconfig dependency warning Signed-off-by: NOlof Johansson <olof@lixom.net>
-
https://github.com/Broadcom/stblinux由 Olof Johansson 提交于
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 5.2-rc1, please pull the following: - Florian fixes the remaining Broadcom DTS files to have a valid device_type = "memory" property which was missed during the removal of skeleton.dtsi * tag 'arm-soc/for-5.2/devicetree-fixes' of https://github.com/Broadcom/stblinux: ARM: dts: bcm: Add missing device_type = "memory" property Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Olof Johansson 提交于
Merge tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes Fixes for omap variants for dra7 mmc voltage and boot issues This series contains dra7 mmc voltage fixes, and fixes to the recent changes to probe devices with device tree data insteas of legacy platform data: - Two fixes for dra7 mmc that needs 1.8V mode disabled as in case of a reset, the bootrom will try to access the mmc card at 3.3V potentially damaging the card - Two regression fixes for am335x d_can. We must allow devices with no control registers for ti-sysc interconnect target module driver for at least d_can, and we remove the incorrect control registers for d_can. And we must configure the osc clock for d_can as otherwise register access may fail depending on the bootloader version - Four regression fixes for dra7 variant dts files to tag rtc and usb4 as disabled for dra71x and dra76x. These SoC variants do not have these devices, and got accidentally enabled when the L4 interconnect got defined in the dra7-l4.dtsi for the dra7 SoC family * tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: dra71x: Disable usb4_tm target module ARM: dts: dra71x: Disable rtc target module ARM: dts: dra76x: Disable usb4_tm target module ARM: dts: dra76x: Disable rtc target module ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values ARM: dts: am57xx-idk: Remove support for voltage switching for SD card bus: ti-sysc: Handle devices with no control registers ARM: dts: Configure osc clock for d_can on am335x Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Olof Johansson 提交于
Merge tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes i.MX fixes for 5.2: - A build fix for soc-imx8 driver which needs SOC_BUS support. To avoid dealing with the dependency for every single i.MX SoC bus driver, we selects at from architecture level. - A fix on i.MX SCU firmware driver to ensure SCU irq is enabled only after IPC is ready. - A regression fix on cpuidle-imx6sx driver, which causes some characters loss on serial communication. * tag 'imx-fixes-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: imx: cpuidle-imx6sx: Restrict the SW2ISO increase to i.MX6SX firmware: imx: SCU irq should ONLY be enabled after SCU IPC is ready arm64: imx: Fix build error without CONFIG_SOC_BUS Signed-off-by: NOlof Johansson <olof@lixom.net>
-
https://github.com/Broadcom/stblinux由 Olof Johansson 提交于
This pull request contains MAINTAINERS file update for Broadcom ARM/ARM64 SoCs, please pull the following: - Stefan updates his email address under the BCM2835 entry * tag 'arm-soc/for-5.2/maintainers' of https://github.com/Broadcom/stblinux: MAINTAINERS: Update Stefan Wahren email address Signed-off-by: NOlof Johansson <olof@lixom.net>
-
https://github.com/Broadcom/stblinux由 Olof Johansson 提交于
This pull request contains Broadcom ARM/ARM64/MIPS SoCs device drivers fixes for 5.2-rc1, please pull the following: - Florian fixes the biuctrl driver not to create an error condition/path upon unsupported CPU and also fixes the biuctrl driver writes to used a data barrier which is necessary given the HW block design * tag 'arm-soc/for-5.2/drivers-fixes' of https://github.com/Broadcom/stblinux: soc: bcm: brcmstb: biuctrl: Register writes require a barrier soc: brcmstb: Fix error path for unsupported CPUs Signed-off-by: NOlof Johansson <olof@lixom.net>
-
由 Linus Torvalds 提交于
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull x86 fixes from Thomas Gleixner: "The accumulated fixes from this and last week: - Fix vmalloc TLB flush and map range calculations which lead to stale TLBs, spurious faults and other hard to diagnose issues. - Use fault_in_pages_writable() for prefaulting the user stack in the FPU code as it's less fragile than the current solution - Use the PF_KTHREAD flag when checking for a kernel thread instead of current->mm as the latter can give the wrong answer due to use_mm() - Compute the vmemmap size correctly for KASLR and 5-Level paging. Otherwise this can end up with a way too small vmemmap area. - Make KASAN and 5-level paging work again by making sure that all invalid bits are masked out when computing the P4D offset. This worked before but got broken recently when the LDT remap area was moved. - Prevent a NULL pointer dereference in the resource control code which can be triggered with certain mount options when the requested resource is not available. - Enforce ordering of microcode loading vs. perf initialization on secondary CPUs. Otherwise perf tries to access a non-existing MSR as the boot CPU marked it as available. - Don't stop the resource control group walk early otherwise the control bitmaps are not updated correctly and become inconsistent. - Unbreak kgdb by returning 0 on success from kgdb_arch_set_breakpoint() instead of an error code. - Add more Icelake CPU model defines so depending changes can be queued in other trees" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback x86/kasan: Fix boot with 5-level paging and KASAN x86/fpu: Don't use current->mm to check for a kthread x86/kgdb: Return 0 from kgdb_arch_set_breakpoint() x86/resctrl: Prevent NULL pointer dereference when local MBM is disabled x86/resctrl: Don't stop walking closids when a locksetup group is found x86/fpu: Update kernel's FPU state before using for the fsave header x86/mm/KASLR: Compute the size of the vmemmap section properly x86/fpu: Use fault_in_pages_writeable() for pre-faulting x86/CPU: Add more Icelake model numbers mm/vmalloc: Avoid rare case of flushing TLB with weird arguments mm/vmalloc: Fix calculation of direct map addr range
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull timer fixes from Thomas Gleixner: "A set of small fixes: - Repair the ktime_get_coarse() functions so they actually deliver what they are supposed to: tick granular time stamps. The current code missed to add the accumulated nanoseconds part of the timekeeper so the resulting granularity was 1 second. - Prevent the tracer from infinitely recursing into time getter functions in the arm architectured timer by marking these functions notrace - Fix a trivial compiler warning caused by wrong qualifier ordering" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timekeeping: Repair ktime_get_coarse*() granularity clocksource/drivers/arm_arch_timer: Don't trace count reader functions clocksource/drivers/timer-ti-dm: Change to new style declaration
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull RAS fixes from Thomas Gleixner: "Two small fixes for RAS: - Use a proper search algorithm to find the correct element in the CEC array. The replacement was a better choice than fixing the crash causes by the original search function with horrible duct tape. - Move the timer based decay function into thread context so it can actually acquire the mutex which protects the CEC array to prevent corruption" * 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: RAS/CEC: Convert the timer callback to a workqueue RAS/CEC: Fix binary search function
-
- 16 6月, 2019 4 次提交
-
-
git://git.infradead.org/linux-platform-drivers-x86由 Linus Torvalds 提交于
Pull x86 platform driver fixes from Andy Shevchenko: - fix a couple of Mellanox driver enumeration issues - fix ASUS laptop regression with backlight - fix Dell computers that got a wrong mode (tablet versus laptop) after resume * tag 'platform-drivers-x86-v5.2-3' of git://git.infradead.org/linux-platform-drivers-x86: platform/mellanox: mlxreg-hotplug: Add devm_free_irq call to remove flow platform/x86: mlx-platform: Fix parent device in i2c-mux-reg device registration platform/x86: intel-vbtn: Report switch events when event wakes device platform/x86: asus-wmi: Only Tell EC the OS will handle display hotkeys from asus_nb_wmi
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb由 Linus Torvalds 提交于
Pull USB fixes from Greg KH: "Here are some small USB driver fixes for 5.2-rc5 Nothing major, just some small gadget fixes, usb-serial new device ids, a few new quirks, and some small fixes for some regressions that have been found after the big 5.2-rc1 merge. All of these have been in linux-next for a while with no reported issues" * tag 'usb-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: usb: typec: Make sure an alt mode exist before getting its partner usb: gadget: udc: lpc32xx: fix return value check in lpc32xx_udc_probe() usb: gadget: dwc2: fix zlp handling usb: dwc2: Set actual frame number for completed ISOC transfer for none DDMA usb: gadget: udc: lpc32xx: allocate descriptor with GFP_ATOMIC usb: gadget: fusb300_udc: Fix memory leak of fusb300->ep[i] usb: phy: mxs: Disable external charger detect in mxs_phy_hw_init() usb: dwc2: Fix DMA cache alignment issues usb: dwc2: host: Fix wMaxPacketSize handling (fix webcam regression) USB: Fix chipmunk-like voice when using Logitech C270 for recording audio. USB: usb-storage: Add new ID to ums-realtek usb: typec: ucsi: ccg: fix memory leak in do_flash USB: serial: option: add Telit 0x1260 and 0x1261 compositions USB: serial: pl2303: add Allied Telesis VT-Kit3 USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS mode
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux由 Linus Torvalds 提交于
Pull powerpc fixes from Michael Ellerman: "One fix for a regression introduced by our 32-bit KASAN support, which broke booting on machines with "bootx" early debugging enabled. A fix for a bug which broke kexec on 32-bit, introduced by changes to the 32-bit STRICT_KERNEL_RWX support in v5.1. Finally two fixes going to stable for our THP split/collapse handling, discovered by Nick. The first fixes random crashes and/or corruption in guests under sufficient load. Thanks to: Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu Malaterre" * tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/32s: fix booting with CONFIG_PPC_EARLY_DEBUG_BOOTX powerpc/64s: __find_linux_pte() synchronization vs pmdp_invalidate() powerpc/64s: Fix THP PMD collapse serialisation powerpc: Fix kexec failure on book3s/32
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace由 Linus Torvalds 提交于
Pull tracing fixes from Steven Rostedt: - Out of range read of stack trace output - Fix for NULL pointer dereference in trace_uprobe_create() - Fix to a livepatching / ftrace permission race in the module code - Fix for NULL pointer dereference in free_ftrace_func_mapper() - A couple of build warning clean ups * tag 'trace-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: ftrace: Fix NULL pointer dereference in free_ftrace_func_mapper() module: Fix livepatch/ftrace module text permissions race tracing/uprobe: Fix obsolete comment on trace_uprobe_create() tracing/uprobe: Fix NULL pointer dereference in trace_uprobe_create() tracing: Make two symbols static tracing: avoid build warning with HAVE_NOP_MCOUNT tracing: Fix out-of-range read in trace_stack_print()
-
- 15 6月, 2019 18 次提交
-
-
由 Borislav Petkov 提交于
Adric Blake reported the following warning during suspend-resume: Enabling non-boot CPUs ... x86: Booting SMP configuration: smpboot: Booting Node 0 Processor 1 APIC 0x2 unchecked MSR access error: WRMSR to 0x10f (tried to write 0x0000000000000000) \ at rIP: 0xffffffff8d267924 (native_write_msr+0x4/0x20) Call Trace: intel_set_tfa intel_pmu_cpu_starting ? x86_pmu_dead_cpu x86_pmu_starting_cpu cpuhp_invoke_callback ? _raw_spin_lock_irqsave notify_cpu_starting start_secondary secondary_startup_64 microcode: sig=0x806ea, pf=0x80, revision=0x96 microcode: updated to revision 0xb4, date = 2019-04-01 CPU1 is up The MSR in question is MSR_TFA_RTM_FORCE_ABORT and that MSR is emulated by microcode. The log above shows that the microcode loader callback happens after the PMU restoration, leading to the conjecture that because the microcode hasn't been updated yet, that MSR is not present yet, leading to the #GP. Add a microcode loader-specific hotplug vector which comes before the PERF vectors and thus executes earlier and makes sure the MSR is present. Fixes: 400816f6 ("perf/x86/intel: Implement support for TSX Force Abort") Reported-by: NAdric Blake <promarbler14@gmail.com> Signed-off-by: NBorislav Petkov <bp@suse.de> Reviewed-by: NThomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> Cc: x86@kernel.org Link: https://bugzilla.kernel.org/show_bug.cgi?id=203637
-
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup由 Linus Torvalds 提交于
Pull cgroup fixes from Tejun Heo: "This has an unusually high density of tricky fixes: - task_get_css() could deadlock when it races against a dying cgroup. - cgroup.procs didn't list thread group leaders with live threads. This could mislead readers to think that a cgroup is empty when it's not. Fixed by making PROCS iterator include dead tasks. I made a couple mistakes making this change and this pull request contains a couple follow-up patches. - When cpusets run out of online cpus, it updates cpusmasks of member tasks in bizarre ways. Joel improved the behavior significantly" * 'for-5.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: cpuset: restore sanity to cpuset_cpus_allowed_fallback() cgroup: Fix css_task_iter_advance_css_set() cset skip condition cgroup: css_task_iter_skip()'d iterators must be advanced before accessed cgroup: Include dying leaders with live threads in PROCS iterations cgroup: Implement css_task_iter_skip() cgroup: Call cgroup_release() before __exit_signal() docs cgroups: add another example size for hugetlb cgroup: Use css_tryget() instead of css_tryget_online() in task_get_css()
-
git://anongit.freedesktop.org/drm/drm由 Linus Torvalds 提交于
Pull drm fixes from Daniel Vetter: "Nothing unsettling here, also not aware of anything serious still pending. The edid override regression fix took a bit longer since this seems to be an area with an overabundance of bad options. But the fix we have now seems like a good path forward. Next week it should be back to Dave. Summary: - fix regression on amdgpu on SI - fix edid override regression - driver fixes: amdgpu, i915, mediatek, meson, panfrost - fix writecombine for vmap in gem-shmem helper (used by panfrost) - add more panel quirks" * tag 'drm-fixes-2019-06-14' of git://anongit.freedesktop.org/drm/drm: (25 commits) drm/amdgpu: return 0 by default in amdgpu_pm_load_smu_firmware drm/amdgpu: Fix bounds checking in amdgpu_ras_is_supported() drm: add fallback override/firmware EDID modes workaround drm/edid: abstract override/firmware EDID retrieval drm/i915/perf: fix whitelist on Gen10+ drm/i915/sdvo: Implement proper HDMI audio support for SDVO drm/i915: Fix per-pixel alpha with CCS drm/i915/dmc: protect against reading random memory drm/i915/dsi: Use a fuzzy check for burst mode clock check drm/amdgpu/{uvd,vcn}: fetch ring's read_ptr after alloc drm/panfrost: Require the simple_ondemand governor drm/panfrost: make devfreq optional again drm/gem_shmem: Use a writecombine mapping for ->vaddr drm: panel-orientation-quirks: Add quirk for GPD MicroPC drm: panel-orientation-quirks: Add quirk for GPD pocket2 drm/meson: fix G12A primary plane disabling drm/meson: fix primary plane disabling drm/meson: fix G12A HDMI PLL settings for 4K60 1000/1001 variations drm/mediatek: call mtk_dsi_stop() after mtk_drm_crtc_atomic_disable() drm/mediatek: clear num_pipes when unbind driver ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2由 Linus Torvalds 提交于
Pull gfs2 fix from Andreas Gruenbacher: "Fix rounding error in gfs2_iomap_page_prepare" * tag 'gfs2-v5.2.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2: gfs2: Fix rounding error in gfs2_iomap_page_prepare
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi由 Linus Torvalds 提交于
Pull SCSI fix from James Bottomley: "A single bug fix for hpsa. The user visible consequences aren't clear, but the ioaccel2 raid acceleration may misfire on the malformed request assuming the payload is big enough to require chaining (more than 31 sg entries)" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: hpsa: correct ioaccel2 chaining
-
git://git.kernel.dk/linux-block由 Linus Torvalds 提交于
Pull block fixes from Jens Axboe: - Remove references to old schedulers for the scheduler switching and blkio controller documentation (Andreas) - Kill duplicate check for report zone for null_blk (Chaitanya) - Two bcache fixes (Coly) - Ensure that mq-deadline is selected if zoned block device is enabled, as we need that to support them (Damien) - Fix io_uring memory leak (Eric) - ps3vram fallout from LBDAF removal (Geert) - Redundant blk-mq debugfs debugfs_create return check cleanup (Greg) - Extend NOPLM quirk for ST1000LM024 drives (Hans) - Remove error path warning that can now trigger after the queue removal/addition fixes (Ming) * tag 'for-linus-20190614' of git://git.kernel.dk/linux-block: block/ps3vram: Use %llu to format sector_t after LBDAF removal libata: Extend quirks for the ST1000LM024 drives with NOLPM quirk bcache: only set BCACHE_DEV_WB_RUNNING when cached device attached bcache: fix stack corruption by PRECEDING_KEY() blk-mq: remove WARN_ON(!q->elevator) from blk_mq_sched_free_requests blkio-controller.txt: Remove references to CFQ block/switching-sched.txt: Update to blk-mq schedulers null_blk: remove duplicate check for report zone blk-mq: no need to check return value of debugfs_create functions io_uring: fix memory leak of UNIX domain socket inode block: force select mq-deadline for zoned block devices
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux由 Linus Torvalds 提交于
Pull i2c fixes from Wolfram Sang: "I2C has two simple but wanted driver fixes for you" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: pca-platform: Fix GPIO lookup code i2c: acorn: fix i2c warning
-
由 Casey Schaufler 提交于
The 5.1 mount system rework changed the smackfsdef mount option to smackfsdefault. This fixes the regression by making smackfsdef treated the same way as smackfsdefault. Also fix the smack_param_specs[] to have "smack" prefixes on all the names. This isn't visible to a user unless they either: (a) Try to mount a filesystem that's converted to the internal mount API and that implements the ->parse_monolithic() context operation - and only then if they call security_fs_context_parse_param() rather than security_sb_eat_lsm_opts(). There are no examples of this upstream yet, but nfs will probably want to do this for nfs2 or nfs3. (b) Use fsconfig() to configure the filesystem - in which case security_fs_context_parse_param() will be called. This issue is that smack_sb_eat_lsm_opts() checks for the "smack" prefix on the options, but smack_fs_context_parse_param() does not. Fixes: c3300aaf ("smack: get rid of match_token()") Fixes: 2febd254 ("smack: Implement filesystem context security hooks") Cc: stable@vger.kernel.org Reported-by: NJose Bollo <jose.bollo@iot.bzh> Signed-off-by: NCasey Schaufler <casey@schaufler-ca.com> Signed-off-by: NDavid Howells <dhowells@redhat.com> Tested-by: NCasey Schaufler <casey@schaufler-ca.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Wei Li 提交于
The mapper may be NULL when called from register_ftrace_function_probe() with probe->data == NULL. This issue can be reproduced as follow (it may be covered by compiler optimization sometime): / # cat /sys/kernel/debug/tracing/set_ftrace_filter #### all functions enabled #### / # echo foo_bar:dump > /sys/kernel/debug/tracing/set_ftrace_filter [ 206.949100] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 206.952402] Mem abort info: [ 206.952819] ESR = 0x96000006 [ 206.955326] Exception class = DABT (current EL), IL = 32 bits [ 206.955844] SET = 0, FnV = 0 [ 206.956272] EA = 0, S1PTW = 0 [ 206.956652] Data abort info: [ 206.957320] ISV = 0, ISS = 0x00000006 [ 206.959271] CM = 0, WnR = 0 [ 206.959938] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000419f3a000 [ 206.960483] [0000000000000000] pgd=0000000411a87003, pud=0000000411a83003, pmd=0000000000000000 [ 206.964953] Internal error: Oops: 96000006 [#1] SMP [ 206.971122] Dumping ftrace buffer: [ 206.973677] (ftrace buffer empty) [ 206.975258] Modules linked in: [ 206.976631] Process sh (pid: 281, stack limit = 0x(____ptrval____)) [ 206.978449] CPU: 10 PID: 281 Comm: sh Not tainted 5.2.0-rc1+ #17 [ 206.978955] Hardware name: linux,dummy-virt (DT) [ 206.979883] pstate: 60000005 (nZCv daif -PAN -UAO) [ 206.980499] pc : free_ftrace_func_mapper+0x2c/0x118 [ 206.980874] lr : ftrace_count_free+0x68/0x80 [ 206.982539] sp : ffff0000182f3ab0 [ 206.983102] x29: ffff0000182f3ab0 x28: ffff8003d0ec1700 [ 206.983632] x27: ffff000013054b40 x26: 0000000000000001 [ 206.984000] x25: ffff00001385f000 x24: 0000000000000000 [ 206.984394] x23: ffff000013453000 x22: ffff000013054000 [ 206.984775] x21: 0000000000000000 x20: ffff00001385fe28 [ 206.986575] x19: ffff000013872c30 x18: 0000000000000000 [ 206.987111] x17: 0000000000000000 x16: 0000000000000000 [ 206.987491] x15: ffffffffffffffb0 x14: 0000000000000000 [ 206.987850] x13: 000000000017430e x12: 0000000000000580 [ 206.988251] x11: 0000000000000000 x10: cccccccccccccccc [ 206.988740] x9 : 0000000000000000 x8 : ffff000013917550 [ 206.990198] x7 : ffff000012fac2e8 x6 : ffff000012fac000 [ 206.991008] x5 : ffff0000103da588 x4 : 0000000000000001 [ 206.991395] x3 : 0000000000000001 x2 : ffff000013872a28 [ 206.991771] x1 : 0000000000000000 x0 : 0000000000000000 [ 206.992557] Call trace: [ 206.993101] free_ftrace_func_mapper+0x2c/0x118 [ 206.994827] ftrace_count_free+0x68/0x80 [ 206.995238] release_probe+0xfc/0x1d0 [ 206.995555] register_ftrace_function_probe+0x4a8/0x868 [ 206.995923] ftrace_trace_probe_callback.isra.4+0xb8/0x180 [ 206.996330] ftrace_dump_callback+0x50/0x70 [ 206.996663] ftrace_regex_write.isra.29+0x290/0x3a8 [ 206.997157] ftrace_filter_write+0x44/0x60 [ 206.998971] __vfs_write+0x64/0xf0 [ 206.999285] vfs_write+0x14c/0x2f0 [ 206.999591] ksys_write+0xbc/0x1b0 [ 206.999888] __arm64_sys_write+0x3c/0x58 [ 207.000246] el0_svc_common.constprop.0+0x408/0x5f0 [ 207.000607] el0_svc_handler+0x144/0x1c8 [ 207.000916] el0_svc+0x8/0xc [ 207.003699] Code: aa0003f8 a9025bf5 aa0103f5 f946ea80 (f9400303) [ 207.008388] ---[ end trace 7b6d11b5f542bdf1 ]--- [ 207.010126] Kernel panic - not syncing: Fatal exception [ 207.011322] SMP: stopping secondary CPUs [ 207.013956] Dumping ftrace buffer: [ 207.014595] (ftrace buffer empty) [ 207.015632] Kernel Offset: disabled [ 207.017187] CPU features: 0x002,20006008 [ 207.017985] Memory Limit: none [ 207.019825] ---[ end Kernel panic - not syncing: Fatal exception ]--- Link: http://lkml.kernel.org/r/20190606031754.10798-1-liwei391@huawei.comSigned-off-by: NWei Li <liwei391@huawei.com> Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
-
由 Josh Poimboeuf 提交于
It's possible for livepatch and ftrace to be toggling a module's text permissions at the same time, resulting in the following panic: BUG: unable to handle page fault for address: ffffffffc005b1d9 #PF: supervisor write access in kernel mode #PF: error_code(0x0003) - permissions violation PGD 3ea0c067 P4D 3ea0c067 PUD 3ea0e067 PMD 3cc13067 PTE 3b8a1061 Oops: 0003 [#1] PREEMPT SMP PTI CPU: 1 PID: 453 Comm: insmod Tainted: G O K 5.2.0-rc1-a188339c #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-20181126_142135-anatol 04/01/2014 RIP: 0010:apply_relocate_add+0xbe/0x14c Code: fa 0b 74 21 48 83 fa 18 74 38 48 83 fa 0a 75 40 eb 08 48 83 38 00 74 33 eb 53 83 38 00 75 4e 89 08 89 c8 eb 0a 83 38 00 75 43 <89> 08 48 63 c1 48 39 c8 74 2e eb 48 83 38 00 75 32 48 29 c1 89 08 RSP: 0018:ffffb223c00dbb10 EFLAGS: 00010246 RAX: ffffffffc005b1d9 RBX: 0000000000000000 RCX: ffffffff8b200060 RDX: 000000000000000b RSI: 0000004b0000000b RDI: ffff96bdfcd33000 RBP: ffffb223c00dbb38 R08: ffffffffc005d040 R09: ffffffffc005c1f0 R10: ffff96bdfcd33c40 R11: ffff96bdfcd33b80 R12: 0000000000000018 R13: ffffffffc005c1f0 R14: ffffffffc005e708 R15: ffffffff8b2fbc74 FS: 00007f5f447beba8(0000) GS:ffff96bdff900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffc005b1d9 CR3: 000000003cedc002 CR4: 0000000000360ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: klp_init_object_loaded+0x10f/0x219 ? preempt_latency_start+0x21/0x57 klp_enable_patch+0x662/0x809 ? virt_to_head_page+0x3a/0x3c ? kfree+0x8c/0x126 patch_init+0x2ed/0x1000 [livepatch_test02] ? 0xffffffffc0060000 do_one_initcall+0x9f/0x1c5 ? kmem_cache_alloc_trace+0xc4/0xd4 ? do_init_module+0x27/0x210 do_init_module+0x5f/0x210 load_module+0x1c41/0x2290 ? fsnotify_path+0x3b/0x42 ? strstarts+0x2b/0x2b ? kernel_read+0x58/0x65 __do_sys_finit_module+0x9f/0xc3 ? __do_sys_finit_module+0x9f/0xc3 __x64_sys_finit_module+0x1a/0x1c do_syscall_64+0x52/0x61 entry_SYSCALL_64_after_hwframe+0x44/0xa9 The above panic occurs when loading two modules at the same time with ftrace enabled, where at least one of the modules is a livepatch module: CPU0 CPU1 klp_enable_patch() klp_init_object_loaded() module_disable_ro() ftrace_module_enable() ftrace_arch_code_modify_post_process() set_all_modules_text_ro() klp_write_object_relocations() apply_relocate_add() *patches read-only code* - BOOM A similar race exists when toggling ftrace while loading a livepatch module. Fix it by ensuring that the livepatch and ftrace code patching operations -- and their respective permissions changes -- are protected by the text_mutex. Link: http://lkml.kernel.org/r/ab43d56ab909469ac5d2520c5d944ad6d4abd476.1560474114.git.jpoimboe@redhat.comReported-by: NJohannes Erdfelt <johannes@erdfelt.com> Fixes: 444d13ff ("modules: add ro_after_init support") Acked-by: NJessica Yu <jeyu@kernel.org> Reviewed-by: NPetr Mladek <pmladek@suse.com> Reviewed-by: NMiroslav Benes <mbenes@suse.cz> Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
-
由 Eiichi Tsukata 提交于
Commit 0597c49c ("tracing/uprobes: Use dyn_event framework for uprobe events") cleaned up the usage of trace_uprobe_create(), and the function has been no longer used for removing uprobe/uretprobe. Link: http://lkml.kernel.org/r/20190614074026.8045-2-devel@etsukata.comReviewed-by: NSrikar Dronamraju <srikar@linux.vnet.ibm.com> Signed-off-by: NEiichi Tsukata <devel@etsukata.com> Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
-
由 Eiichi Tsukata 提交于
Just like the case of commit 8b05a3a7 ("tracing/kprobes: Fix NULL pointer dereference in trace_kprobe_create()"), writing an incorrectly formatted string to uprobe_events can trigger NULL pointer dereference. Reporeducer: # echo r > /sys/kernel/debug/tracing/uprobe_events dmesg: BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 8000000079d12067 P4D 8000000079d12067 PUD 7b7ab067 PMD 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 1903 Comm: bash Not tainted 5.2.0-rc3+ #15 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014 RIP: 0010:strchr+0x0/0x30 Code: c0 eb 0d 84 c9 74 18 48 83 c0 01 48 39 d0 74 0f 0f b6 0c 07 3a 0c 06 74 ea 19 c0 83 c8 01 c3 31 c0 c3 0f 1f 84 00 00 00 00 00 <0f> b6 07 89 f2 40 38 f0 75 0e eb 13 0f b6 47 01 48 83 c RSP: 0018:ffffb55fc0403d10 EFLAGS: 00010293 RAX: ffff993ffb793400 RBX: 0000000000000000 RCX: ffffffffa4852625 RDX: 0000000000000000 RSI: 000000000000002f RDI: 0000000000000000 RBP: ffffb55fc0403dd0 R08: ffff993ffb793400 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: ffff993ff9cc1668 R14: 0000000000000001 R15: 0000000000000000 FS: 00007f30c5147700(0000) GS:ffff993ffda00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000007b628000 CR4: 00000000000006f0 Call Trace: trace_uprobe_create+0xe6/0xb10 ? __kmalloc_track_caller+0xe6/0x1c0 ? __kmalloc+0xf0/0x1d0 ? trace_uprobe_create+0xb10/0xb10 create_or_delete_trace_uprobe+0x35/0x90 ? trace_uprobe_create+0xb10/0xb10 trace_run_command+0x9c/0xb0 trace_parse_run_command+0xf9/0x1eb ? probes_open+0x80/0x80 __vfs_write+0x43/0x90 vfs_write+0x14a/0x2a0 ksys_write+0xa2/0x170 do_syscall_64+0x7f/0x200 entry_SYSCALL_64_after_hwframe+0x49/0xbe Link: http://lkml.kernel.org/r/20190614074026.8045-1-devel@etsukata.com Cc: stable@vger.kernel.org Fixes: 0597c49c ("tracing/uprobes: Use dyn_event framework for uprobe events") Reviewed-by: NSrikar Dronamraju <srikar@linux.vnet.ibm.com> Signed-off-by: NEiichi Tsukata <devel@etsukata.com> Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
-
由 YueHaibing 提交于
Fix sparse warnings: kernel/trace/trace.c:6927:24: warning: symbol 'get_tracing_log_err' was not declared. Should it be static? kernel/trace/trace.c:8196:15: warning: symbol 'trace_instance_dir' was not declared. Should it be static? Link: http://lkml.kernel.org/r/20190614153210.24424-1-yuehaibing@huawei.comAcked-by: NTom Zanussi <tom.zanussi@linux.intel.com> Reported-by: NHulk Robot <hulkci@huawei.com> Signed-off-by: NYueHaibing <yuehaibing@huawei.com> Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
-
由 Vasily Gorbik 提交于
Selecting HAVE_NOP_MCOUNT enables -mnop-mcount (if gcc supports it) and sets CC_USING_NOP_MCOUNT. Reuse __is_defined (which is suitable for testing CC_USING_* defines) to avoid conditional compilation and fix the following gcc 9 warning on s390: kernel/trace/ftrace.c:2514:1: warning: ‘ftrace_code_disable’ defined but not used [-Wunused-function] Link: http://lkml.kernel.org/r/patch.git-1a82d13f33ac.your-ad-here.call-01559732716-ext-6629@work.hours Fixes: 2f4df001 ("tracing: Add -mcount-nop option support") Signed-off-by: NVasily Gorbik <gor@linux.ibm.com> Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
-
由 Eiichi Tsukata 提交于
Puts range check before dereferencing the pointer. Reproducer: # echo stacktrace > trace_options # echo 1 > events/enable # cat trace > /dev/null KASAN report: ================================================================== BUG: KASAN: use-after-free in trace_stack_print+0x26b/0x2c0 Read of size 8 at addr ffff888069d20000 by task cat/1953 CPU: 0 PID: 1953 Comm: cat Not tainted 5.2.0-rc3+ #5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014 Call Trace: dump_stack+0x8a/0xce print_address_description+0x60/0x224 ? trace_stack_print+0x26b/0x2c0 ? trace_stack_print+0x26b/0x2c0 __kasan_report.cold+0x1a/0x3e ? trace_stack_print+0x26b/0x2c0 kasan_report+0xe/0x20 trace_stack_print+0x26b/0x2c0 print_trace_line+0x6ea/0x14d0 ? tracing_buffers_read+0x700/0x700 ? trace_find_next_entry_inc+0x158/0x1d0 s_show+0xea/0x310 seq_read+0xaa7/0x10e0 ? seq_escape+0x230/0x230 __vfs_read+0x7c/0x100 vfs_read+0x16c/0x3a0 ksys_read+0x121/0x240 ? kernel_write+0x110/0x110 ? perf_trace_sys_enter+0x8a0/0x8a0 ? syscall_slow_exit_work+0xa9/0x410 do_syscall_64+0xb7/0x390 ? prepare_exit_to_usermode+0x165/0x200 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f867681f910 Code: b6 fe ff ff 48 8d 3d 0f be 08 00 48 83 ec 08 e8 06 db 01 00 66 0f 1f 44 00 00 83 3d f9 2d 2c 00 00 75 10 b8 00 00 00 00 04 RSP: 002b:00007ffdabf23488 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007f867681f910 RDX: 0000000000020000 RSI: 00007f8676cde000 RDI: 0000000000000003 RBP: 00007f8676cde000 R08: ffffffffffffffff R09: 0000000000000000 R10: 0000000000000871 R11: 0000000000000246 R12: 00007f8676cde000 R13: 0000000000000003 R14: 0000000000020000 R15: 0000000000000ec0 Allocated by task 1214: save_stack+0x1b/0x80 __kasan_kmalloc.constprop.0+0xc2/0xd0 kmem_cache_alloc+0xaf/0x1a0 getname_flags+0xd2/0x5b0 do_sys_open+0x277/0x5a0 do_syscall_64+0xb7/0x390 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Freed by task 1214: save_stack+0x1b/0x80 __kasan_slab_free+0x12c/0x170 kmem_cache_free+0x8a/0x1c0 putname+0xe1/0x120 do_sys_open+0x2c5/0x5a0 do_syscall_64+0xb7/0x390 entry_SYSCALL_64_after_hwframe+0x44/0xa9 The buggy address belongs to the object at ffff888069d20000 which belongs to the cache names_cache of size 4096 The buggy address is located 0 bytes inside of 4096-byte region [ffff888069d20000, ffff888069d21000) The buggy address belongs to the page: page:ffffea0001a74800 refcount:1 mapcount:0 mapping:ffff88806ccd1380 index:0x0 compound_mapcount: 0 flags: 0x100000000010200(slab|head) raw: 0100000000010200 dead000000000100 dead000000000200 ffff88806ccd1380 raw: 0000000000000000 0000000000070007 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888069d1ff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888069d1ff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888069d20000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff888069d20080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888069d20100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Link: http://lkml.kernel.org/r/20190610040016.5598-1-devel@etsukata.com Fixes: 4285f2fc ("tracing: Remove the ULONG_MAX stack trace hackery") Signed-off-by: NEiichi Tsukata <devel@etsukata.com> Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
-
由 Andreas Gruenbacher 提交于
The pos and len arguments to the iomap page_prepare callback are not block aligned, so we need to take that into account when computing the number of blocks. Fixes: d0a22a4b ("gfs2: Fix iomap write page reclaim deadlock") Signed-off-by: NAndreas Gruenbacher <agruenba@redhat.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux由 Linus Torvalds 提交于
Pull arm64 fixes from Will Deacon: "Here are some arm64 fixes for -rc5. The only non-trivial change (in terms of the diffstat) is fixing our SVE ptrace API for big-endian machines, but the majority of this is actually the addition of much-needed comments and updates to the documentation to try to avoid this mess biting us again in future. There are still a couple of small things on the horizon, but nothing major at this point. Summary: - Fix broken SVE ptrace API when running in a big-endian configuration - Fix performance regression due to off-by-one in TLBI range checking - Fix build regression when using Clang" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64/sve: Fix missing SVE/FPSIMD endianness conversions arm64: tlbflush: Ensure start/end of address range are aligned to stride arm64: Don't unconditionally add -Wno-psabi to KBUILD_CFLAGS
-
由 Linus Torvalds 提交于
Merge misc fixes from Andrew Morton: "16 fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: mm/devm_memremap_pages: fix final page put race PCI/P2PDMA: track pgmap references per resource, not globally lib/genalloc: introduce chunk owners PCI/P2PDMA: fix the gen_pool_add_virt() failure path mm/devm_memremap_pages: introduce devm_memunmap_pages drivers/base/devres: introduce devm_release_action() mm/vmscan.c: fix trying to reclaim unevictable LRU page coredump: fix race condition between collapse_huge_page() and core dumping mm/mlock.c: change count_mm_mlocked_page_nr return type mm: mmu_gather: remove __tlb_reset_range() for force flush fs/ocfs2: fix race in ocfs2_dentry_attach_lock() mm/vmscan.c: fix recent_rotated history mm/mlock.c: mlockall error for flag MCL_ONFAULT scripts/decode_stacktrace.sh: prefix addr2line with $CROSS_COMPILE mm/list_lru.c: fix memory leak in __memcg_init_list_lru_node mm: memcontrol: don't batch updates of local VM stats and events
-
- 14 6月, 2019 2 次提交
-
-
git://people.freedesktop.org/~agd5f/linux由 Daniel Vetter 提交于
Fixes for 5.2: - Extend previous vce fix for resume to uvd and vcn - Fix bounds checking in ras debugfs interface - Fix a regression on SI using amdgpu Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch> From: Alex Deucher <alexdeucher@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190613021856.3307-1-alexander.deucher@amd.com
-
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu由 Linus Torvalds 提交于
Pull iommu fixes from Joerg Roedel: - three fixes for Intel VT-d to fix a potential dead-lock, a formatting fix and a bit setting fix - one fix for the ARM-SMMU to make it work on some platforms with sub-optimal SMMU emulation * tag 'iommu-fixes-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu/arm-smmu: Avoid constant zero in TLBI writes iommu/vt-d: Set the right field for Page Walk Snoop iommu/vt-d: Fix lock inversion between iommu->lock and device_domain_lock iommu: Add missing new line for dma type
-