This patch adds check for pending work event before queueing
relogin work to prevent redundant work to be active at the
same time.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add check to allow single discovery command per session to be sent
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Switch scan is assumed to succeed most of the time.
If the scan failed, then scan is limit 5 retries.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Delay loop id allocation to login time
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add verbose bit for debug messages to reduce excessive
log messages
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When any kind of reset is issued, current code was setting
state of LOGIN pending too early. This resulted into driver
not retrying relogin until pervious reloin completes.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

add ability to use gpnft/gnnft to handle RSCN.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch fixes issue with extraction of ADISC error codes
for decoding the error returned
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

retry gpnft/gnnft if error is encountered.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current code creates a session when a new port is
discovered, and a PLOGI/PRLI is received. There is
no need to create session when command has arrived.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Migrate switch registration commands: RFTID, RFFID, RNNID and RSNN_NN
out of mailbox interface to reduce fabric scan bottle neck.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Relogin stop moving forward due to improper check of scan_state flag.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add NPIV id check to reduce multiple debug messages
of the same RSCN event.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

reduce usage of terminate exchange when command encounter
resource bottle neck.  Remote initiator view it as command
drop.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Host lookup via btree is currently protected by the hardware_lock.
Add hardware_lock when modifying btree to store host pointer.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

- add "async" gpn_ft, gnn_ft, gfpn_id, gnn_id switch commands.
- For 8G and newer adapters, use async commands when it comes to
fabric scan to reduce bottle neck.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When connection type is N_Port to N_Port (point-to-point), there
is a possibilty where initiator will not send PLOGI request and
will directly send PRLI. In N2N connection the port has higher
port name sends the PLOGI but not allow to send PRLI if is a
target mode. Only initiator is allowed to send PRLI.

Current driver code deletes old session when it receives PLOGI
request. If we will not receive PLOGI request then we will not
delete old session and create new session. Add check for N2N
with PRLI receive only and trigger cleanup. For this case, the
cleanup requires individual cmd abort instead of using implicit
logout as a broad stroke flush.
Signed-off-by: NKrishna Kant <krishna.kant@purestorage.com>
Signed-off-by: NAlexei Potashnik <alexei@purestorage.com>
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fetch actual data from firmware instead of static data
at chip reset time.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For Dual Mode, Initiator side of the driver finish login,
target side receive PRLI, but driver terminates PRLI.
This patch allows target side to go ahead and accept PRLI.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The logo ELS command allocates dma coherent memory for the
data payload and serialize the completions. When this command
times out, the timeout routine completes the thread waiting
for completion which in turn cleanup resources allocated for
this ELS command processing. Don't call generic sp->free
routine when this ELS command times out to avoid to double
freeing of the same resources.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add ability to send Implicit PRLO to flush IOs
from FW back to driver.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add option to tell FW to reserve 1/2 of emergency exchanges for ELS.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For ISP27XX, use shadow register to read FW provided REQQ's consumer
index. The shadow register is dma'ed by firmware.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Enable ATIO Q interrupt handshake for ISP27XX. This patch
coalesce ATIO's interrupts for Quad port ISP27XX adapter.
Interrupt coalesce allows performance to scale for this
specific case.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

DPC thread can stall during switch scan due to slow switch response.
This will stall other work element that needs attention. Moving work
element processing and relogin logic out of DPC thread and into its
own work queue.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replace call to Get Port DataBase MB with PDO_FORCE_ADISC
flag with async ADISC command so driver can see ADISC command
has error or not.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adjusts and reallocates fw_dump memory for target mode
to save for extended login and exchange offload buffers into
dump captured.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

As part of chip reset, all commands from all QPairs are
flushed. This patch fixes code to use Q Pair lock for flush
instead of using old hardware_lock.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Max boundary for exchange off load is 32k exchanges. If a system
is unable to allocate large memory buffer to support this feature,
then driver will reduce the number of exchanges down to a value
system can support.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current code uses Stop Firmware MB cmd to stop the chip before
driver unload.  This will leave the laser in its current state.
This give the illusion of this adapter is still alive.
For 8G & newer adapters, use chip reset to stop the chip and
bring down the laser.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use IOCB patch to submit Control VP MBX command to reduce
bottle-neck for mbx interface.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

when processing iocb in a timeout case, driver was trying to log messages
without verifying if the fcport structure could have valid data. This
results in a NULL pointer access.

Fixes: 726b8548("qla2xxx: Add framework for async fabric discovery")
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

hpsa_show_dev_msg prints other information and a newline after the
message string, so the message string does not need to include a newline
explicitly.  Done using Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update driver Version to 50877
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Earlier driver would scan throgh all supported buses and targets and add
devices that responded. It would add devices that were _hidden_ by the fw.
Driver would invalidate commands sent to _hidden_ devices via the
AAC_HIDE_DISK check.

Since the driver now adds only the devices that are supposed to be
exposed, this code can be removed.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove unused rescan variable.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is a chance of the driver to be stuck in kdump if drives start
acting up in kdump discovery process and the kernel decides to send eh
resets, which would prompt rescan to be scheduled.

Do not perform a rescan in kdump context, since we do not expect a hotplug
event during kdump and all the devices are going to go away anyway.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add back the ability to scan for hotplug changes while eh was in progress.

Schedule a rescan for a later time in the eh recovery code and wait for
eh to complete in the rescan worker.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If the driver fails to retrieve information from the fw (could happen when
the fw is not fully in its senses), the driver does nothing and change is
not processed correctly by the driver

Schedule host rescan in case of failure. This is only for SAFW, since
the information retrieval failure will happen on SAFW devices.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>