Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 23 12月, 2015 11 次提交
  3. 17 12月, 2015 21 次提交
  5. 15 12月, 2015 8 次提交
    • G
      usb: phy: Remove unused Renesas R-Car (Gen1) USB PHY driver · 375da627
      由 Geert Uytterhoeven 提交于 
      As of commit 3d7608e4 ("ARM: shmobile: bockw: remove legacy
board file and config"), the Renesas R-Car (Gen1) USB PHY driver is no
longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that would
require adding DT support to the driver. Instead, a new driver using the
generic PHY framework should be written, as was done for R-Car Gen2.

Remove the driver for good.
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      375da627
    • V
      usb: gadget: lpc32xxx_udc: clean up and sort include directives out · 2de59c09
      由 Vladimir Zapolskiy 提交于 
      Remove mach/irq.h from the list of included headers, there is no
compilation dependency on this include file, and the change is needed
to prevent a compilation failure, when mach/irq.h is removed.

Additionally remove other unneeded includes and sort out their order.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      2de59c09
    • F
      usb: dwc3: trace: show request flags · 46a01427
      由 Felipe Balbi 提交于 
      struct usb_request have 3 flags which might be
important to know about during debug. This patch
shows each of the 3 flags as a single letter:

z -> for zero
s -> short not okay
i -> interrupt

A capital letter means the feature is enabled
while a lower case letter means it is disabled;

Thus 'zsI' indicates that a ZLP is not needed,
that we can accept a short packet and interrupt
for this request should be enabled.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      46a01427
    • F
      usb: dwc3: gadget: handle request->zero · 04c03d10
      由 Felipe Balbi 提交于 
      So far, dwc3 has always missed request->zero
handling for every endpoint. Let's implement
that so we can handle cases where transfer must
be finished with a ZLP.

Note that dwc3 is a little special. Even though
we're dealing with a ZLP, we still need a buffer
of wMaxPacketSize bytes; to hide that detail from
every gadget driver, we have a preallocated buffer
of 1024 bytes (biggest bulk size) to use (and
share) among all endpoints.
Reported-by: NRavi B <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      04c03d10
    • R
      usb: musb: convert printk to pr_* · 3ff4b573
      由 Rasmus Villemoes 提交于 
      This file already uses pr_debug in a few places; this converts the
remaining printks.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      3ff4b573
    • D
      usb: dwc2: host: Clear interrupts before handling them · 29539019
      由 Douglas Anderson 提交于 
      In general it is wise to clear interrupts before processing them.  If
you don't do that, you can get:
 1. Interrupt happens
 2. You look at system state and process interrupt
 3. A new interrupt happens
 4. You clear interrupt without processing it.

This patch was actually a first attempt to fix missing device insertions
as described in (usb: dwc2: host: Fix missing device insertions) and it
did solve some of the signal bouncing problems but not all of
them (which is why I submitted the other patch).  Specifically, this
patch itself would sometimes change:
 1. hardware sees connect
 2. hardware sees disconnect
 3. hardware sees connect
 4. dwc2_port_intr() - clears connect interrupt
 5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()

...to:
 1. hardware sees connect
 2. hardware sees disconnect
 3. dwc2_port_intr() - clears connect interrupt
 4. hardware sees connect
 5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()

...but with different timing then sometimes we'd still miss cable
insertions.

In any case, though this patch doesn't fix any (known) problems, it
still seems wise as a general policy to clear interrupt before handling
them.

Note that for dwc2_handle_usb_port_intr(), instead of moving the clear
of PRTINT to the beginning of the function we remove it completely.  The
only way to clear PRTINT is to clear the sources that set it in the
first place.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      29539019
    • D
      usb: dwc2: host: Add missing spinlock in dwc2_hcd_reset_func() · 4a065c7b
      由 Douglas Anderson 提交于 
      The dwc2_hcd_reset_func() function is only ever called directly by a
delayed work function.  As such no locks are already held when the
function is called.

Doing a read-modify-write of CPU registers and setting fields in the
main hsotg data structure is a bad idea without locks.  Let's add
locks.

The bug was found by code inspection only.  It turns out that the
dwc2_hcd_reset_func() is only ever called today if the
"host_support_fs_ls_low_power" parameter is enabled and no code in
mainline enables that parameter.  Thus no known issues in mainline are
fixed by this patch, but it's still probably wise to fix the function.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      4a065c7b
    • B
      usb: of: add an api to get dr_mode by the phy node · 98bfb394
      由 Bin Liu 提交于 
      Some USB phy drivers have different handling for the controller in each
dr_mode. But the phy driver does not have visibility to the dr_mode of
the controller.

This adds an api to return the dr_mode of the controller which
associates the given phy node.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
      98bfb394