Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.

Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

USB devices do not require the chip test routine.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To inject a packet in monitor mode, a dummy station has
to be associated with the monitor interface in the target.
Failing to do this would result in a firmware crash on the device.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_eeprom_mode_from_channel() returns -1 on error but we're storing
the result in "ee_mode" which is an unsigned char.  This breaks the
error handling.  This patch makes "ee_mode" an int.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove some obvious looking dead code and rename few functions
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 0ce3bcfc.

Event though with the above commit we obtain the configured DTIM period
from the AP rather than always hardcoding it to '1', this seems to cause
problems under the following scenarios:
* Preventing association with broken AP's
* Adds latency in roaming
So its better to always use the safe value of '1' for dtim period

Cc: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An Rx DMA descriptor can have multiple error bits set, and some error
bits (e.g. MIC failure) are filtered by the driver based on other criteria.
Remove the 'else' in various error bit checks so that all error information
is properly passed to the driver.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And add the copyright/license header.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When returning to the operating channel, a full HW
reset has to be done instead of a fast channel change.
Since sw_scan_complete() is called after the config() call for the
home channel, we end up doing a FCC. Fix this issue by checking
the OFFCHANNEL flag to determine FCC.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The device has to be reset when a FATAL event is received.
Not doing so would leave the card in a non-working state.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to lock the various work cancellation
calls. This will be helpful when handling FATAL events.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When doing a channel change, the pending URBs have to be killed
properly on calling htc_stop().

This fixes the probe response timeout seen when sending UDP traffic at
a high rate and running background scan at the same time.

Cc: stable <stable@kernel.org>
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some minor clean ups in assigning values to beacon config parameters
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch revamps some common code-paths which are
shared between (re-)initialization and suspend/resume
subroutines. It also adds some helpful comments
about quirks and associated difficulties.

It's quite big, but it should fix #25382:
<https://bugzilla.kernel.org/show_bug.cgi?id=25382>

And hopefully the code is robust enough to deal with
all possible suspend/resume scenarios without requiring
the user to do any sort of manual and possibly
dangerous work.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By removing two "safety" msleeps (and an echo nop), the
channel change delay is effectively halved. Previously,
the delay could be as long as 260 ms and the device
could not go off-channel without risking to miss the
next DTIM beacon [interval ~307 ms].
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a forgotten bail-out path.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_reset is called from process context and takes the cc_lock
with plain spin_lock(), but cc_lock can also be taken from tasklets
in softirq context.  Thus we need to at least use spin_lock_bh.

This fixes the following lockdep warning:

[   19.967874] sky2 0000:01:00.0: eth0: enabling interface
[   19.982761] ieee80211 phy0: device now idle
[   20.904809] NET: Registered protocol family 17
[   21.243857] ieee80211 phy0: device no longer idle - scanning
[   21.404343]
[   21.404346] =================================
[   21.404450] [ INFO: inconsistent lock state ]
[   21.404518] 2.6.37-rc7-wl+ #242
[   21.404582] ---------------------------------
[   21.404650] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[   21.404721] kworker/u:4/982 [HC0[0]:SC1[3]:HE1:SE0] takes:
[   21.404792]  (&(&common->cc_lock)->rlock){+.?...}, at: [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011] {SOFTIRQ-ON-W} state was registered at:
[   21.405011]   [<c105cadd>] __lock_acquire+0x62f/0x13c1
[   21.405011]   [<c105d944>] lock_acquire+0xd5/0xf1
[   21.405011]   [<c12c978d>] _raw_spin_lock+0x45/0x72
[   21.405011]   [<f8111533>] ath5k_reset+0x2c0/0x349 [ath5k]
[   21.405011]   [<f8111a7a>] ath5k_start+0xb8/0x139 [ath5k]
[   21.405011]   [<f849c714>] ieee80211_do_open+0x13f/0x819 [mac80211]
[   21.405011]   [<f849ce51>] ieee80211_open+0x63/0x66 [mac80211]
[   21.405011]   [<c1258b2e>] __dev_open+0x8d/0xb6
[   21.405011]   [<c1255c64>] __dev_change_flags+0x9d/0x114
[   21.405011]   [<c1258a75>] dev_change_flags+0x18/0x44
[   21.405011]   [<c1262990>] do_setlink+0x23f/0x521
[   21.405011]   [<c1262d58>] rtnl_setlink+0xe6/0xea
[   21.405011]   [<c126347c>] rtnetlink_rcv_msg+0x18a/0x1a0
[   21.405011]   [<c126d5f0>] netlink_rcv_skb+0x35/0x7b
[   21.405011]   [<c12632eb>] rtnetlink_rcv+0x20/0x27
[   21.405011]   [<c126d370>] netlink_unicast+0x1bb/0x21e
[   21.405011]   [<c126db21>] netlink_sendmsg+0x23b/0x288
[   21.405011]   [<c124823c>] sock_sendmsg+0xac/0xc4
[   21.405011]   [<c1248680>] sys_sendmsg+0x152/0x1a2
[   21.405011]   [<c1249b0d>] sys_socketcall+0x214/0x275
[   21.405011]   [<c10029d0>] sysenter_do_call+0x12/0x36
[   21.405011] irq event stamp: 138032
[   21.405011] hardirqs last  enabled at (138032): [<c12ca252>] _raw_spin_unlock_irqrestore+0x3b/0x5e
[   21.405011] hardirqs last disabled at (138031): [<c12c98cc>] _raw_spin_lock_irqsave+0x18/0x7e
[   21.405011] softirqs last  enabled at (138024): [<f84a570e>] ieee80211_tx_skb+0x47/0x49 [mac80211]
[   21.405011] softirqs last disabled at (138027): [<c100452b>] do_softirq+0x63/0xb4
[   21.405011]
[   21.405011] other info that might help us debug this:
[   21.405011] 3 locks held by kworker/u:4/982:
[   21.405011]  #0:  (name){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b
[   21.405011]  #1:  ((&(&local->scan_work)->work)){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b
[   21.405011]  #2:  (&local->mtx){+.+.+.}, at: [<f84920fb>] ieee80211_scan_work+0x32/0x4a4 [mac80211]
[   21.405011]
[   21.405011] stack backtrace:
[   21.405011] Pid: 982, comm: kworker/u:4 Not tainted 2.6.37-rc7-wl+ #242
[   21.405011] Call Trace:
[   21.405011]  [<c12c6e68>] ? printk+0x1d/0x25
[   21.405011]  [<c105a742>] print_usage_bug+0x181/0x18b
[   21.405011]  [<c105b196>] ? check_usage_forwards+0x0/0xb6
[   21.405011]  [<c105a9ec>] mark_lock+0x2a0/0x4aa
[   21.405011]  [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd
[   21.405011]  [<c105ca68>] __lock_acquire+0x5ba/0x13c1
[   21.405011]  [<c1059eed>] ? trace_hardirqs_off_caller+0x18/0x8d
[   21.405011]  [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd
[   21.405011]  [<c1050411>] ? local_clock+0x2c/0x4f
[   21.405011]  [<c1059e00>] ? save_trace+0x2/0xa0
[   21.405011]  [<c105ac39>] ? mark_held_locks+0x43/0x5b
[   21.405011]  [<c12ca252>] ? _raw_spin_unlock_irqrestore+0x3b/0x5e
[   21.405011]  [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<c105d944>] lock_acquire+0xd5/0xf1
[   21.405011]  [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<c12c9b1a>] _raw_spin_lock_bh+0x4a/0x77
[   21.405011]  [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<c105ac39>] ? mark_held_locks+0x43/0x5b
[   21.405011]  [<f8113496>] ath5k_tasklet_ani+0x1d/0x27 [ath5k]
[   21.405011]  [<c1037304>] tasklet_action+0x96/0x137
[   21.405011]  [<c10379b5>] __do_softirq+0xde/0x1c3
[   21.405011]  [<c10b0cef>] ? arch_get_unmapped_area_topdown+0x3b/0x127
[   21.405011]  [<c10378d7>] ? __do_softirq+0x0/0x1c3
[   21.405011]  <IRQ>  [<c1036dee>] ? irq_exit+0x3d/0x49
[   21.405011]  [<c1003b4f>] ? do_IRQ+0x98/0xac
[   21.405011]  [<c1002eee>] ? common_interrupt+0x2e/0x34
[   21.405011]  [<c103007b>] ? sys_unshare+0x57/0x226
[   21.405011]  [<c1047fee>] ? queue_delayed_work+0x1/0x27
[   21.405011]  [<f84a83a0>] ? ieee80211_queue_delayed_work+0x2e/0x33 [mac80211]
[   21.405011]  [<f8492528>] ? ieee80211_scan_work+0x45f/0x4a4 [mac80211]
[   21.405011]  [<c104620e>] ? process_one_work+0x26e/0x41b
[   21.405011]  [<c1046158>] ? process_one_work+0x1b8/0x41b
[   21.405011]  [<f84920c9>] ? ieee80211_scan_work+0x0/0x4a4 [mac80211]
[   21.405011]  [<c10466b6>] ? worker_thread+0x18a/0x2a5
[   21.405011]  [<c12ca25e>] ? _raw_spin_unlock_irqrestore+0x47/0x5e
[   21.405011]  [<c104652c>] ? worker_thread+0x0/0x2a5
[   21.405011]  [<c104abe7>] ? kthread+0x67/0x6c
[   21.405011]  [<c104ab80>] ? kthread+0x0/0x6c
[   21.405011]  [<c1002efa>] ? kernel_thread_helper+0x6/0x10
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For the AR9002, the spur frequency read from the EEPROM is mangled
before being compared against AR_NO_SPUR.  This results in the driver
trying to set up the spur mitigation for bogus spurs, rather than
cleanly breaking out.
Signed-off-by: NBrian Prodoehl <bprodoehl@nomadio.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disabling BH is not required while running from a tasklet context
and so replace spin_lock_bh with just spin_lock.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move mac80211 functions into new file mac80211-ops.c to have a better
separation and to make base.c smaller.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It looks like some hardware registers are left into undefined state
after suspend/resume. At minimum, this can cause odd issues related to
key cache and hardware trying to encrypt/decrypt frames unexpectedly.
This seems to happen even when there is no keys configured, i.e., hardware
can end up touching TX frames just based of invalid key cache context
even if the driver is not asking a specific entry to be used. In
addition, RX can likely be affected. This patch fixes this issue.
Signed-off-by: NJouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The size of the eeprom data is 1088 bytes for AR9485. But
a sanity check is done against 4K which would result in a
'potential read past the end of the buffer' smatch complaint.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Introduce a helper function to get the EEPROM mode from channel and remove
multiple similar switch statements. Also since it's now easy to get the EEPROM
mode from the channel, use them inside the functions which need it, instead of
passing a redundant ee_mode parameter.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove redundant defines.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a new variable to keep track of the currently configured tx power. Before
max_pwr was re-used for keeping the maximum allowed power as well as the
current configuration. Doing a min() on it allows you to lower the txpower, but
how would you be able to make it higher again?

This patch fixes that by adding a new variable ah_cur_pwr which is used instead
of txp_max_pwr to keep the current configuration. txp_max_pwr is used to check
if we are within the limits.

Another problem fixed by this patch is that it avoids setting a zero txpower
when things are initialized first and the current power is not yet set.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And rename functions which write the powertable to make it clearer.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Let ath5k_hw_txpower() decide if it can re-use the powertable or if it has to
be recalculated instead of passing a 'fast' flag from the outside.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a missing unlock when we hit the "No beacon slot available"
error condition.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use function pci_is_pcie() instead of accessing struct member directly.

CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use function pci_is_pcie() instead of accessing struct member directly.

CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recently added warning message on power change failure
is not needed on device removal.

ath: Failed to wakeup in 500us
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/hw.c:1618
ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]()
Hardware name: 64756D6
Pid: 540, comm: kworker/u:3 Not tainted 2.6.37-rc6-wl #37
Call Trace:
 [<ffffffff810501aa>] warn_slowpath_common+0x7a/0xb0
 [<ffffffffa056e280>] ? ath9k_iowrite32+0x0/0x90 [ath9k]
 [<ffffffff810501f5>] warn_slowpath_null+0x15/0x20
 [<ffffffffa05226ef>] ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]
 [<ffffffffa05700e5>] ath9k_ps_wakeup+0x85/0xd0 [ath9k]
 [<ffffffffa0570685>] ath9k_configure_filter+0x25/0x80 [ath9k]
 [<ffffffffa04dde43>] ieee80211_configure_filter+0x133/0x190 [mac80211]
 [<ffffffffa04ee502>] ieee80211_do_stop+0x132/0x540 [mac80211]
 [<ffffffff813466ff>] ? _raw_spin_unlock_bh+0x1f/0x30
 [<ffffffff812b6923>] ? dev_deactivate+0x1c3/0x1e0
 [<ffffffffa04ee925>] ieee80211_stop+0x15/0x20 [mac80211]
 [<ffffffff8129d1b6>] __dev_close+0x56/0x90
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: warn if we cannot change the power to the chip"
introduced a new warning to indicate chip powerup failures, but this
is not required for devices that have been removed. Handle USB device
removal properly by checking for unplugged status.

For PCI devices, this warning will still be seen when the card is pulled
out, not sure how to check for card removal.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Restricting the chainmask to 1 for legacy mode disables useful features
such as MRC, and it reduces the available transmit power.
I can't think of a good reason to do this in legacy mode, so let's just
get rid of that code.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>