The T540p has a touchpad with pnp-id LEN0034, all the models with this
pnp-id have the same min/max values, except the T540p where the values are
slightly off. Fix them to be identical.

This is a preparation patch for simplifying the quirk table.

Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

https://bugzilla.redhat.com/show_bug.cgi?id=1096436

Cc: stable@vger.kernel.org
Tested-and-reported-by: ajayr@bigfoot.com
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

We expect that all the Haswell series will need such quirks, sigh.

The T431s seems to be T430 hardware in a T440s case, using the T440s touchpad,
with the same min/max issue.

The X1 Carbon 3rd generation name says 2nd while it is a 3rd generation.

The X1 and T431s share a PnPID with the T540p, but the reported ranges are
closer to those of the T440s.

HdG: Squashed 5 quirk patches into one. T431s + L440 + L540 are written by me,
S1 Yoga and X1 are written by Benjamin Tissoires.

Hdg: Standardized S1 Yoga and X1 values, Yoga uses the same touchpad as the
X240, X1 uses the same touchpad as the T440.

Cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Check PNP ID of the PS/2 AUX port and report INPUT_PROP_TOPBUTTONPAD
property for for touchpads with top button areas.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This extends Benjamin Tissoires manual min/max quirk table with support for
the ThinkPad X240.

Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.

Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.

We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).

So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

__initconst should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

In summary, the symptom is intermittent key events lost after resume
on some machines with synaptics touchpad (seems this is synaptics _only_),
and key events loss is due to serio port reconnect after psmouse sync lost.
Removing psmouse and inserting it back during the suspend/resume process
is able to work around the issue, so the difference between psmouse_connect()
and psmouse_reconnect() is the key to the root cause of this problem.

After comparing the two different paths, synaptics driver has its own
implementation of synaptics_reconnect(), and the missing psmouse_probe()
seems significant, the patch below added psmouse_probe() to the reconnect
process, and has been verified many times that the issue could not be reliably
reproduced.

There are two PS/2 commands in psmouse_probe():

  1. PSMOUSE_CMD_GETID
  2. PSMOUSE_CMD_RESET_DIS

Only the PSMOUSE_CMD_GETID seems to be significant. The
PSMOUSE_CMD_RESET_DIS is irrelevant to this issue after trying
several times.  So we have only implemented this patch to issue
the PSMOUSE_CMD_GETID so far.
Tested-by: NDaniel Manrique <daniel.manrique@canonical.com>
Signed-off-by: NJames M Leddy <james.leddy@canonical.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

To properly setup event parameters for emulated events, pass
the appropriate flag to the slot initialization function. Also,
all MT-related events should be setup before initialization.

Incidentally, this solves the issue of doubly filtered pointer
events.
Reported-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Investigating the following gesture highlighted two slight implementation
errors with choosing which slots to report in which slot when multiple
contacts are present:

Action                 SGM  AGM (MTB slot:Contact)
1. Touch contact 0    (0:0)
2. Touch contact 1    (0:0, 1:1)
3. Lift  contact 0    (1:1)
4. Touch contacts 2,3 (0:2, 1:3)

In step 4, slot 1 was not being cleared first, which means the same
tracking ID was being used for reporting both the old contact 1 and the
new contact 3.  This could result in "drumroll", where the old contact 1
would appear to suddenly jump to new finger 3 position.

Similarly, if contacts 2 & 3 are not detected at the same sample, step 4
is split into two:

Action                SGM  AGM  (MTB slot:contact)
1. Touch contact 0   (0:0)
2. Touch contact 1   (0:0, 1:1)
3. Lift  contact 0   (1:1)
4. Touch contact 2   (0:2, 1:1)
5. Touch contact 3   (0:2, 1:3)

In this case, there was also a bug.  In step 4, when contact 1 moves from
SGM to AGM and contact 2 is first reported in SGM, slot 0 was actually
empty.  So slot 0 can be used to report the new SGM (contact 0),
immediately.  Since it was empty, contact 2 in slot 0 will get a new
tracking ID.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Commit c0394506 (Input: synaptics - handle out of bounds values from the
hardware) caused any hardware reported values over 7167 to be treated as
a wrapped-around negative value. It turns out that some firmware uses
the value 8176 to indicate a finger near the edge of the touchpad whose
actual position cannot be determined. This value now gets treated as
negative, which can cause pointer jumps and broken edge scrolling on
these machines.

I only know of one touchpad which reports negative values, and this
hardware never reports any value lower than -8 (i.e. 8184). Moving the
threshold for treating a value as negative up to 8176 should work fine
then for any hardware we currently know about, and since we're dealing
with unspecified behavior it's probably the best we can do. The special
8176 value is also likely to result in sudden jumps in position, so
let's also clamp this to the maximum specified value for the axis.

BugLink: http://bugs.launchpad.net/bugs/1046512
https://bugzilla.kernel.org/show_bug.cgi?id=46371

Cc: stable@vger.kernel.org
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Tested-by: NAlan Swanson <swanson@ukfsn.org>
Tested-by: NArteom <arutemus@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Preparing to move more repeated code into the mt core, add a flags
argument to the input_mt_slots_init() function.
Reviewed-and-tested-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: NPing Cheng <pingc@wacom.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

The touchpad on the Acer Aspire One D250 will report out of range values
in the extreme lower portion of the touchpad. These appear as abrupt
changes in the values reported by the hardware from very low values to
very high values, which can cause unexpected vertical jumps in the
position of the mouse pointer.

What seems to be happening is that the value is wrapping to a two's
compliment negative value of higher resolution than the 13-bit value
reported by the hardware, with the high-order bits being truncated. This
patch adds handling for these values by converting them to the
appropriate negative values.

The only tricky part about this is deciding when to treat a number as
negative. It stands to reason that if out of range values can be
reported on the low end then it could also happen on the high end, so
not all out of range values should be treated as negative. The approach
taken here is to split the difference between the maximum legitimate
value for the axis and the maximum possible value that the hardware can
report, treating values greater than this number as negative and all
other values as positive. This can be tweaked later if hardware is found
that operates outside of these parameters.

BugLink: http://bugs.launchpad.net/bugs/1001251
Cc: stable@vger.kernel.org
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Read the Firmware ID and Board Number from a synaptics device at init
and display them in the system log.

Device behavior is very board and firmware dependent.
It may prove useful for users to include this information when providing
bug reports or other feedback.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Move synaptics_invert_y() inside CONFIG_MOUSE_PS2_SYNAPTICS to get rid of
a compile warning when we don't select synaptics support.

drivers/input/mouse/synaptics.c:53:12: warning: ‘synaptics_invert_y’ defined but not used [-Wunused-function]
Signed-off-by: NJJ Ding <dgdunix@gmail.com>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

commit 7968a5dd
Input: synaptics - add support for Relative mode

Accidentally broke support for advanced gestures (multitouch)
on some trackpads such as the one in my ThinkPad X220 by
incorretly changing the condition for enabling them. This
restores it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org [3.3]
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Synaptics touchpads on several Dell laptops, particularly Vostro V13
systems, may not respond properly to PS/2 commands and queries immediately
after resuming from suspend to RAM. This leads to unresponsive touchpad
after suspend/resume cycle.

Adding a 1-second delay after resetting the device allows touchpad to
finish initializing (calibrating?) and start reacting properly.
Reported-by: NDaniel Manrique <daniel.manrique@canonical.com>
Tested-by: NDaniel Manrique <daniel.manrique@canonical.com>
Cc: stable@kernel.org
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We have determined that the jumpiness previously seen when using
the synaptics kernel mouse driver on OLPC XO was due to not using
the synaptics X11 userspace driver - the xf86-input-evdev driver was
interpreting 'finger near pad' signals as movements. Newer versions
of xf86-input-evdev fix this issue.

Additionally, the synaptics kernel driver is now usable on this
platform, but only when run in relative mode.

Update the comment and refine the check to allow the synaptics driver
to run on OLPC XO in relative mode.

We will continue investigating the EC issue as time becomes available.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Currently, the synaptics driver puts the device into Absolute mode.
As explained in the synaptics documentation section 3.2, in this mode,
the device sends a continuous stream of packets at the maximum rate
to the host when the user's fingers are near or on the pad or
pressing buttons, and continues streaming for 1 second afterwards.
These packets are even sent when there is no new information to report,
even when they are duplicates of the previous packet.

For embedded systems this is a bit much - it results in a huge
and uninterrupted stream of interrupts at high rate.

This patch adds support for Relative mode, which can be selected as
a new psmouse protocol. In this mode, the device does not send duplicate
packets and acts like a standard PS/2 mouse. However, synaptics-specific
functionality is still available, such as the ability to set the packet
rate, and rather than disabling gestures and taps at the hardware level
unconditionally, a 'synaptics_disable_gesture' sysfs attribute has
been added to allow control of this functionality.

This solves a long standing OLPC issue: synaptics hardware enables
tap to click by default (even in the default relative mode), but we
have found this to be inappropriate for young children and first
time computer users. Enabling the synaptics driver disables tap-to-click,
but we have previously been unable to use this because it also enables
Absolute mode, which is too "spammy" for our desires and actually
overloads our EC with its continuous stream of packets. Now we can enable
the synaptics driver, disabling tap to click while retaining the less
noisy Relative mode.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This will ensure our reporting is consistent with the rest of the system
and we do not refer to obsolete source file names.
Reviewed-by: NWanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: NJJ Ding <dgdunix@gmail.com>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Synaptics image sensor touchpads track up to 5 fingers, but only report 2.
They use a special "TYPE=2" (AGM-CONTACT) packet type that reports
the number of tracked fingers and which finger is reported in the SGM
and AGM packets.

With this new packet type, it is possible to tell userspace when 4 or 5
fingers are touching.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Synaptics image sensor touchpads track 5 fingers, but only report 2.
This patch attempts to deal with some idiosyncrasies of these touchpads:

 * When there are 3 or more fingers, only two are reported.
 * The touchpad tracks the 5 fingers in slot[0] through slot[4].
 * It always reports the lowest and highest valid slots in SGM and AGM
   packets, respectively.
 * The number of fingers is only reported in the SGM packet.  However,
   the number of fingers can change either before or after an AGM
   packet.
 * Thus, if an SGM reports a different number of fingers than the last
   SGM, it is impossible to tell whether the intervening AGM corresponds
   to the old number of fingers or the new number of fingers.
 * For example, when going from 2->3 fingers, it is not possible to tell
   whether tell AGM contains slot[1] (old 2nd finger) or slot[2] (new
   3rd finger).
 * When fingers are added one at at time, from 1->2->3, it is possible to
   track which slots are contained in the SGM and AGM packets:
     1 finger:  SGM = slot[0], no AGM
     2 fingers: SGM = slot[0], AGM = slot[1]
     3 fingers: SGM = slot[0], AGM = slot[2]
 * It is also possible to track which slot is contained in the SGM when 1
   of 2 fingers is removed.  This is because the touchpad sends a special
   (0,0,0) AGM packet whenever all fingers are removed except slot[0]:
     Last AGM == (0,0,0): SGM contains slot[1]
     Else: SGM contains slot[0]
 * However, once there are 3 fingers, if exactly 1 finger is removed, it
   is impossible to tell which 2 slots are contained in SGM and AGM.
   The (SGM,AGM) could be (0,1), (0,2), or (1,2). There is no way to know.
 * Similarly, if two fingers are simultaneously removed (3->1), then it
   is only possible to know if SGM still contains slot[0].
 * Since it is not possible to reliably track which slot is being
   reported, we invalidate the tracking_id every time the number of
   fingers changes until this ambiguity is resolved when:
     a) All fingers are removed.
     b) 4 or 5 fingers are touched, generates an AGM-CONTACT packet.
     c) All fingers are removed except slot[0].  In this special case, the
        ambiguity is resolved since by the (0,0,0) AGM packet.

Behavior of the driver:

When 2 or more fingers are present on the touchpad, the kernel reports
up to two MT-B slots containing the position data for two of the fingers
reported by the touchpad.  If the identity of a finger cannot be tracked
when the number-of-fingers changes, the corresponding MT-B slot will be
invalidated (track_id set to -1), and a new track_id will be assigned in
a subsequent input event report.

The driver always reports the total number of fingers using one of the
EV_KEY/BTN_TOOL_*TAP events. This could differ from the number of valid
MT-B slots for two reasons:
 a) There are more than 2 fingers on the pad.
 b) During ambiguous number-of-fingers transitions, the correct track_id
    for one or both of the slots cannot be determined, so the slots are
    invalidated.

Thus, this is a hybrid singletouch/MT-B scheme. Userspace can detect
this behavior by noting that the driver supports more EV_KEY/BTN_TOOL_*TAP
events than its maximum EV_ABS/ABS_MT_SLOT.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

A Synaptics image sensor tracks 5 fingers, but can only report 2.

The algorithm for choosing which 2 fingers to report and in which packet:
  Touchpad maintains 5 slots, numbered 0 to 4
  Initially all slots are empty
  As new fingers are detected, assign them to the lowest available slots
  The touchpad always reports:
    SGM: lowest numbered non-empty slot
    AGM: highest numbered non-empty slot, if there is one

In addition, these touchpads have a special AGM packet type which reports
the number of fingers currently being tracked, and which finger is in
each of the two slots.  Unfortunately, these "TYPE=2" packets are only used
when more than 3 fingers are being tracked.  When less than 4 fingers
are present, the 'w' value must be used to track how many fingers are
present, and knowing which fingers are being reported is much more
difficult, if not impossible.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Synaptics makes (at least) two kinds of touchpad sensors:
 * Older pads use a profile sensor that could only infer the location
   of individual fingers based on the projection of their profiles
   onto row and column sensors.
 * Newer pads use an image sensor that can track true finger position
   using a two-dimensional sensor grid.

Both sensor types support an "Advanced Gesture Mode":
 When multiple fingers are detected, the touchpad sends alternating
 "Advanced Gesture Mode" (AGM) and "Simple Gesture Mode" (SGM)
 packets.
 The AGM packets have w=2, and contain reduced resolution finger data
 The SGM packets have w={0,1} and contain full resolution finger data

Profile sensors try to report the "upper" (larger y value) finger in
the SGM packet, and the lower (smaller y value) in the AGM packet.
However, due to the nature of the profile sensor, they easily get
confused when fingers cross, and can start reporting the x-coordinate
of one with the y-coordinate of the other.  Thus, for profile
sensors, "semi-mt" was created, which reports a "bounding box"
created by pairing min and max coordinates of the two pairs of
reported fingers.

Image sensors can report the actual coordinates of two of the fingers
present.  This patch detects if the touchpad is an image sensor and
reports finger data using the MT-B protocol.

NOTE: This patch only adds partial support for 2-finger gestures.
      The proper interpretation of the slot contents when more than
      two fingers are present is left to later patches.  Also,
      handling of 'number of fingers' transitions is incomplete.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

When a Synaptics touchpad is in "AGM" mode, and multiple fingers are
detected, the touchpad sends alternating "Advanced Gesture Mode" (AGM) and
"Simple Gesture Mode" (SGM) packets.
  The AGM packets have w=2, and contain reduced resolution finger data.
  The SGM packets have w={0,1} and contain full resolution finger data.

Refactor the parsing of agm packets to its own function, and rename the
synaptics_data.mt field to .agm to indicate that it contains the contents of
the last agm packet.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Synaptics touchpads report increasing y from bottom to top.
This is inverted from normal userspace "top of screen is 0" coordinates.
Thus, the kernel driver reports inverted y coordinates to userspace.

This patch refactors this inversion.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Newer Synaptics firmware allows to query minimum coordinates reported by
the device, let's use this data.
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

AGM packets contain valid button bits, too.
This patch refactors packet processing to parse button bits in AGM packets.
However, they aren't actually used or reported.

The point is to more completely process AGM packets,
and prepare for future patches that may actually use AGM packet button bits.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Synaptics touchpads indicate via a capability bit when they perform reduced
filtering on position data. In such a case, use a non-zero fuzz value.
Fuzz = 8 was chosen empirically by observing the raw position data
reported by a clickpad indicating it had reduced filtering.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Set resolution for MT_POSITION_X and MT_POSITION_Y to match ABS_X and
ABS_Y, respectively.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

'struct dmi_system_id' arrays must always have a terminator to keep
dmi_check_system() from looking at data (and possibly crashing) it
isn't supposed to look at.

The issue went unnoticed until ef8313bb,
but was introduced about a year earlier with
7705d548 (which also similarly changed
lifebook.c, but the problem there got eliminated shortly afterwards).

The first hunk therefore is a stable candidate back to 2.6.33, while
the full change is needed only on 2.6.38.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: stable@kernel.org
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

On some machines, like Dell Studio XPS 16 (1640), touchpad fails to
respond to the standard query after first reset but may start
responding later, so let's repeat reset sequence several (3) times.
Signed-off-by: NAlexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

synaptics_set_advanced_gesture_mode() affect capabilities bits we should
perform comparison after calling this function, otherwise they will never
match and we will be forced to perform full reconnect.
Signed-off-by: NAlexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

OLPC has switched to a Synaptics touchpad.  It turns out that it's
pretty useless in absolute mode.  This patch looks for an OLPC
system (via DMI tables), and refuses to init Synaptics mode in
that scenario (falling back to relative mode).
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Minor comment fixup for typos and grammar. Noticed while adding a
separate workaround.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

In multitouch mode, at least one device (fw: 7.4 id: 0x1c0b1) sometimes
sends a final main packet with x == 1. Since the normal values are above
1472, this is clearly bogus. At the same time, a two-finger touch is
signaled, even though only one finger was on the pad to begin with. This
patch ignores the packet altogether, removing the problem.
Acked-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NChase Douglas <chase.douglas@canonical.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>

The Synaptics 2.7 series of touchpads support a mode for reporting two
sets of X/Y/Pressure data (advanced gesture mode). By default, these
devices report only single finger data, depriving userspace of the
nowadays ubiquitous two-finger scroll gesture.

Enabling advanced gesture mode also enables the multi-finger report,
although the device does not claim that capability. Up to three
fingers can be reported this way.

While two or three fingers are touching, the normal packet is
prepended by a reduced finger packet of lower resolution. From the two
packets (which do not represent the actual fingers), the bounding
rectangle of the individual contacts can be extracted.  This
information is sufficient to perform scaling gestures and a limited
form of rotation gesture. The behavior has been coined semi-mt
capability, and is signaled to userspace via the INPUT_PROP_SEMI_MT
device property.

Work to decode the advanced gesture packet: Takashi Iwai.
Cleanup and testing of the original patch: Chase Douglas.
Minor cleanup and testing: Chris Bagwell.
Finalization and semi-mt support: Henrik Rydberg.

Reported-by: Tobyn Bertram
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NChase Douglas <chase.douglas@canonical.com>
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>