The A31 has 2 parallel display pipelines, which can be intermixed.
However the driver currently only supports one of them.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The pinmux setting nodes for the A31 were added out of alphabetical
order. Sort them.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Use the new sun7i-a20-mmc compatible for the mmc controllers on sun7i
and newer.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now that we have a different clock representation, switch to it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

mmc2 and mmc3 are available on the same pins, with different mux values.
However, only mmc3 supports 8 bit DDR transfer modes.

Since preference for mmc3 over mmc2 is due to DDR transfer modes, just
set the drive strength to 40mA, which is needed for DDR.

This pinmux setting also includes the hardware reset pin for emmc.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.

Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a pinmux setting for using mmc2 in regular 4 bit mode.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

When the gpio interrupt bindings where changed to add a bank to the
specifier list, the r_pio nodes of A23/A31/A33 where not updated to
match and neither was the pio node of the A80, this fixes this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This also includes the reset pin for emmc.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

sun6i also has the LRADC for tablet buttons.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

A31/A31s have the same "Security System" crypto engine as A10/A20,
but with a separate reset control.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The A31 gates have a non continuous set of clock IDs that are valid. Add
the clock-indices property to the DT to express this.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMichael Turquette <mturquette@baylibre.com>

The current DTs were setting the cell size to 2, but used the default xlate
function that was assuming an interrupt cell size of 1, leading to the
second part of the cell (the flags) being ignored, while we were having an
inconsistent binding between the interrupts and gpio (that could also be
used as interrupts).

That "binding" doesn't work either with newer SoCs that have multiple irq
banks.

Now that we fixed the pinctrl driver to handle this like it should always
have been handled, convert the DT users, and while we're at it, remove the
size-cells property of PIO that is completely useless.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Add a node for the otg/drc usb controller to sun6i-a31.dtsi.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

A few lines (probably copy pasted) have an indentation mixing tabs and
spaces that triggers a checkpatch warning.

Fix those, and while we're at it, fix the space-indented sections.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

A few lines in our DTSIs are over the 80 characters limit, making
checkpatch complain about that.

If possible (and relevant), wrap these lines to 80 characters.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.

Remove it from our DT, as suggested.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

On sun6i we already have PLL6 as AHB1 clock's parent. However this was
previously set in the dma controller node, which takes effect when the
dma controller is probed.

We want this to take effect as soon as possible, so hrtimer rate
calculation is correct, and to be sure the AHB1 clock rate remains as
stable as possible.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.

The operating points were taken from the a list compiled by Maxime Ripard,
which is based on A31 FEX files from the sunxi-boards repository. Not all
boards have the same settings. The settings in this patch are the ones
shared by A/B/C revisions, plus the default clock setting from u-boot.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

mmc1 is used to connect to the WiFi chip on the Hummingbird A31.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
[maxime: Changed the drive and pull values for their defines]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Sometimes we need to specify non-probably information for sdio devices in the
devicetree, this is done through child nodes addressed by the reg property,
whereby the reg property refers to the sdio function number, see;
Documentation/devicetree/bindings/mmc/mmc.txt

This commit adds the necessary address- and size-cells properties to the mmc
controller nodes in the dtsi files, so that dts files needing such a child
node do not need to specify these themselves.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The p2wi controller has only one possible pinmux setting. Use it by
default in the dtsi, instead of having to set it in each board's dts.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: reformat commit title; rename p2wi pins and use as default]
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Commit f77d55a3 ("serial: 8250_dw: get index of serial line from DT
aliases") made the serial driver now use the serial aliases to get the tty
number, pointing out that our aliases have been wrong all along.

Remove them from the DTSI and add custom ones in the relevant boards.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we support the sun6i variant of the touchscreen controller,
add the device node to the dtsi so we can use it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A31 has non-initialized architected timers, without CNTFRQ or CNTVOFF set
by the Allwinner's bootloader.

Use the new DT property for such case, and enable the arch timers.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add simplefb nodes for "[de_fe0-]de_be0-lcd0" and "[de_fe0-]de_be0-lcd0-tve0"
display pipelines for when u-boot has set up a pipeline to drive a LCD panel /
VGA output rather then the HDMI output.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The GIC requires some extra opaque arguments to set the IRQ type and flags.

Convert the DTs to using the common defines.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.

Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Prepare the device trees to use the C preprocessor.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node for the ir receiver found on the A31.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
[Maxime: Added a node label]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add an ir_clk sub-node to the prcm node.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add pinmux settings for the ir receive pin of the A31.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add the sample and output clocks for the MMC phase support.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Tested-by: NChen-Yu Tsai <wens@csie.org>

The clock driver has unified support for the ahb1 clock.
Unify the clock nodes so it works.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This reverts commit 338302ae.

This is one of two commits that resulted in a boot regression.

Conflicts:
	arch/arm/boot/dts/sun6i-a31.dtsi
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/7h1toxr0ku.fsf@deeprootsystems.com

Review of the u-boot sunxi simplefb patches has led to the decision that
u-boot should not use a specific path to find the nodes as this goes contrary
to how devicetree usually works.

Instead a platform specific compatible + properties should be used for this.

The simplefb bindings have already been updated to reflect this, this patch
brings the sunxi devicetree files in line with the new binding, and the
actual u-boot implementation as it is going upstream.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Avoid the parent pll for the mod-clk for de_be0 getting disabled when non of
the other users are enabled (which can happen when none of i2c, spi and mmc
are in use).

Note for now we point directly to the parent rather then to the de_be0 mod-clk
as that is not modelled in our devicetree yet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a simplefb template node for u-boot to further fill and activate.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The apb2 clocks are actually the same as apb1 clocks on the other sunxi
platforms, hence compatible with "allwinner,sun4i-a10-apb1-clk".

Update the dtsi to use the new unified apb1 clk.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>