Use the GIC and standard IRQ binding defines in all IRQ specifiers.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Use TEGRA_GPIO() macro to name all GPIOs referenced by GPIO properties,
and some interrupts properties. Use standard GPIO flag defines too.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Replace /include/ (dtc) with #include (C pre-processor) for all Tegra DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.

This allows future use of #defines and header files in order to define
names for various constants, such as the IDs and flags in GPIO
specifiers. Use of those features will increase the readability of the
device tree files.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add support for general-purpose LEDs present on Beaver
Signed-off-by: NEric Brower <ebrower@nvidia.com>
[swarren: put new node in correct sort order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Tegra30's boot ROM masks the top 1MiB of RAM. Fix the memory node in
Beaver's DT file to reflect this.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Enable SPI4 and add Winbond SPI flash W25Q32DW device
on CS0 line.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch updates all Tegra board files so that they contain all the
properties required by the updated USB DT binding. Note that this patch
only adds the new properties and does not yet remove the old properties,
in order to maintain bisectability. The old properties will be removed
once the driver has been updated to assume the new bindings.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
[swarren: fixed some newly added regulator-name properties to better
match schematic, avoided duplicate regulator-name on Whistler.]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

1. All Tegra20 ULPI reset GPIO DT properties are modified to indicate active
low nature of the GPIO.
2. Placed USB PHY DT node immediately below the EHCI controller DT nodes
and corrected reg value in the name of USB PHY DT node.
Signed-off-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The 'samsung,vbus-gpio' was submitted before pinmux landed for
exynos5250 and uses the old-style gpio specifier.  Fix the two
exynos5250 boards that use it.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Trivial patch, adding the i2c Cypress trackpad used on Snow.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>

If a board isn't using twl4030, then dtc will complain about the missing
phandle (which is in twl4030.dtsi).  Move the phy declaration to the dts
files.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The bootloader configures the pins, but has pull bits
set without pull enable bits. While this is harmless,
and won't do anything, it seems to cause confusion at
least for me every time looking at the pin configuration.
Fix it for DT based boot.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add GPMC data node to AM33XX device tree file.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit d16fb25d (ARM: dts: OMAP4460: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP4460 OPP data in
arch/arm/mach-omap2/opp4xxx_data.c
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit 3027e267 (ARM: dts: OMAP36xx: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP36xx OPP data in
arch/arm/mach-omap2/opp3xxx_data.c
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit ff5c9059 (ARM: dts: OMAP3+: Correct gpio #interrupts-cells
property) updated the number of interrupt cells required for configuring
gpios as interrupts for other devices (such as ethernet controllers).
This update allowed the interrupt type (edge, level, etc) to be
configured via device-tree (as described in the
Documentation/devicetree/bindings/gpio/gpio-omap.txt).

This broke ethernet support on the OMAP4 SDP board that defines a gpio
as the ethernet IRQ because the interrupt type (level, edge, etc) was
not getting configured correctly. This board use the ks8851 ethernet
chip which has an active low interrupt. Fix this by defining the gpio
interrupt as active-low in the device-tree binding.

Please note that the OMAP4-VAR-SOM also uses the same ethernet
controller and it is expected it will have the same problem. So the
same fix is also applied to this board.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I fumbled when resolving a merge conflict on application of commit
765d012c (ARM: dts: exynos4210: Add basic dts file for universal_c210
board), and left out the dts source file. Here it is.
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds basic device tree sources for Universal C210 board.

Currently support includes:
- eMMC
- serial
- max8952 and max8998 voltage regulators.
- gpio-keys

More support will be added in further patches.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds device tree node for PWM block present on Exynos 4 SoCs.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add basic EC information to device tree, currently only describing the
keyboard and keymap.
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Now that we have i2c-arbitrator in place on bus 4 we can add the
sbs-battery driver.  Future devices will be added onto bus 4 once
drivers are in good shape.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

We need to use the i2c-arbitrator to talk to any of the devices on i2c
bus 4 on exynos5250-snow so that we don't confuse the embedded
controller (EC).  Add the i2c-arbitrator to the device tree.  As we
add future devices (keyboard, sbs, tps65090) we'll add them on top of
this.

The arbitrated bus is numbered 104 simply as a convenience to make it
easier for people poking around to guess that it might have something
to do with the physical bus 4.

The addition is split between the cros5250-common and the snow device
tree file since not all cros5250-class devices use arbitration.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Commit 800974ac ("ARM: dts: Add board dts file for ODROID-X") includes a node
to describe the board level properties for mshc controller. But the mshc
controller node was not added in the Exynos4x12 dtsi file which resulted
in the following warning when compiling the dtb files.

Warning (reg_format): "reg" property in /mshc@12550000/slot@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /mshc@12550000/slot@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /mshc@12550000/slot@0

Fix this by adding the mshc controller node for Exynos4x12 SoCs.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Tested-by: NDongjin Kim <tobetter@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This change makes the rtc on the exynos5250 and 5440 disabled by
default to match exynos4.

Ever since the common clock framework came in, exynos5250 boards
have dumped lots of warnings in the boot log. It turns out that
we don't see those on exynos4 since the rtc is disabled by default.
While we need to get to the bottom of the problems with the RTC,
it still makes sense to have the default state of the RTC on exynos
boards match.

For the record, warnings look like this:
  ------------[ cut here ]------------
  WARNING: at drivers/clk/clk.c:771 __clk_enable+0x34/0xb0()
  Modules linked in:
  [<80015bfc>] (unwind_backtrace+0x0/0xec) from [<804717f0>] (dump_stack+0x20/0x24)
  [<804717f0>] (dump_stack+0x20/0x24) from [<80023cd0>] (warn_slowpath_common+0x5c/0x7c)
  [<80023cd0>] (warn_slowpath_common+0x5c/0x7c) from [<80023d1c>] (warn_slowpath_null+0x2c/0x34)
  [<80023d1c>] (warn_slowpath_null+0x2c/0x34) from [<8035ddb0>] (__clk_enable+0x34/0xb0)
  [<8035ddb0>] (__clk_enable+0x34/0xb0) from [<8035de54>] (clk_enable+0x28/0x3c)
  [<8035de54>] (clk_enable+0x28/0x3c) from [<8031a160>] (s3c_rtc_probe+0xf4/0x434)
  [<8031a160>] (s3c_rtc_probe+0xf4/0x434) from [<8028e288>] (platform_drv_probe+0x24/0x28)
  [<8028e288>] (platform_drv_probe+0x24/0x28) from [<8028ce10>] (driver_probe_device+0xbc/0x22c)
  [<8028ce10>] (driver_probe_device+0xbc/0x22c) from [<8028cff8>] (__driver_attach+0x78/0x9c)
  [<8028cff8>] (__driver_attach+0x78/0x9c) from [<8028bdfc>] (bus_for_each_dev+0x64/0xac)
  [<8028bdfc>] (bus_for_each_dev+0x64/0xac) from [<8028c7e0>] (driver_attach+0x28/0x30)
  [<8028c7e0>] (driver_attach+0x28/0x30) from [<8028c43c>] (bus_add_driver+0xe0/0x234)
  [<8028c43c>] (bus_add_driver+0xe0/0x234) from [<8028d55c>] (driver_register+0xac/0x13c)
  [<8028d55c>] (driver_register+0xac/0x13c) from [<8028e4f4>] (platform_driver_register+0x54/0x68)
  [<8028e4f4>] (platform_driver_register+0x54/0x68) from [<8065c944>] (s3c_rtc_driver_init+0x14/0x1c)
  [<8065c944>] (s3c_rtc_driver_init+0x14/0x1c) from [<800086d8>] (do_one_initcall+0x60/0x138)
  [<800086d8>] (do_one_initcall+0x60/0x138) from [<80633a8c>] (kernel_init_freeable+0x108/0x1d0)
  [<80633a8c>] (kernel_init_freeable+0x108/0x1d0) from [<8046d2f8>] (kernel_init+0x1c/0xf4)
  [<8046d2f8>] (kernel_init+0x1c/0xf4) from [<8000e358>] (ret_from_fork+0x14/0x20)
  ---[ end trace 4bcdc801c868d73f ]---
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
CC: rob.herring@calxeda.com
CC: will.deacon@arm.com
CC: arnd@arndb.de

xenvm is based on mach-vexpress, move it to mach-virt.

Changes in v4:
- update the dts Makefile too.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: will.deacon@arm.com
CC: arnd@arndb.de
CC: rob.herring@calxeda.com

Add chip-id controller nodes for Exynos4 and Exynos5 SoCs.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Tested-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
[wenyou.yang@atmel.com: added spi nodes for the sam9263ek, sam9g20ek, sam9m10g45ek and sam9n12ek boards]
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
[wenyou.yang@atmel.com: add spi nodes for sam9260, sam9263, sam9g45 and sam9n12]
[wenyou.yang@atmel.com: remove spi property "cs-gpios" to the board dts files]
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The exynos combiner irqchip needs to find the parent interrupts
and needs to know their number, so add the missing properties
for exynos4 as they were already present for exynos5.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

"atmel,sama5ek" compatibility sting does not correspond to a
useful board configuration. This d34ek.dts is the only sama5d3
.dts file affected.
Reported-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add DMA resources to MCI nodes.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
[nicolas.ferre@atmel.com: correct 9g45, 9n12 dma phandle name]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add DMA resources to i2c nodes.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
[nicolas.ferre@atmel.com: correct 9n12 dma phandle name]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Moving to generic DMA DT binding involves to set #dma-cells to 2.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable m25p64 SPI flash support on da850-EVM. Also
add partition information of SPI flash.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Patch adds SPI1 DT node along with pinmux data.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

In order to be able to use more than 4GB of RAM when the LPAE is
activated, the dts must be converted in 64 bits.

Only Armada XP is LPAE capable, but as it shares a common dtsi file
with Armada 370, then the common file include the skeleton64. Thanks
to the use of the overload capability of the device tree format,
armada-370 include the 32 bit skeleton and all the armada 370 based
dts can remain the same.

This was heavily based on the work of Lior Amsalem.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Introduce a 'internal-regs' subnode, under which all devices are
moved. This is not really needed for now, but will be for the
mvebu-mbus driver. This generates a lot of code movement since it's
indenting by one more tab all the devices.  So it was a good
opportunity to fix all the bad indentation.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This conversion will allow to keep 32 bits addresses for the internal
registers whereas the memory of the system will be 64 bits.
Later it will also ease the move of the mvebu-mbus driver to the
device tree support.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>