The 0xF6 command used to start and stop the recording from 22560 devices
was removed. This is causing an assert when the driver tries to alter
the recording state.
Remove the use of the command.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Unite iwl_trans debug related fields under iwl_trans_debug struct to
increase readability and keep iwl_trans clean.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There are several flows where the driver checks if it runs in ini mode.
Some of these flows are no longer used in ini mode or there is another
condition that check the ini mode in the same flow. Either way, those
conditions are redundant. Remove the redundant conditions.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently we dump only the first 64 bytes of the PCI config space,
which leaves out some important things, such as the base address
registers.

Increase it to 352 for the PCI device and to 524 for the rootport to
make sure we include everything we need.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Improve the robustness of the dump collection flow in case of an early
error:
1. in iwl_trans_pcie_sync_nmi, disable and enable interrupts only if
   they were already enabled
2. attempt to initiate dump collection in iwl_fw_dbg_error_collect only
   if the device is enabled
3. check Tx command queue was already allocated before trying to collect it
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When try to bring up the AX201 2 killer sku, we
run into:
[81261.392463] iwlwifi 0000:01:00.0: loaded firmware version 46.8c20f243.0 op_mode iwlmvm
[81261.407407] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AX 22000, REV=0x340
[81262.424778] iwlwifi 0000:01:00.0: Collecting data: trigger 16 fired.
[81262.673359] iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
[81262.673365] iwlwifi 0000:01:00.0: Status: 0x00000000, count: -906373681
[81262.673368] iwlwifi 0000:01:00.0: Loaded firmware version: 46.8c20f243.0
[81262.673371] iwlwifi 0000:01:00.0: 0x507C015D | ADVANCED_SYSASSERT

Fix this issue by adding 2 more cfg to avoid modifying the
original cfg configuration.
Signed-off-by: NMatt Chen <matt.chen@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Read fseq info from FW registers and print it upon fw assert.
The print is needed since the fseq version coming from the TLV might
not be the actual version that is used.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The driver attempts to clear persistence bit on any device familiy even
though only 9000 and 22000 families require it. Clear the bit only on
the relevant device families.

Each HW has different address to the write protection register. Use the
right register for each HW
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 8954e1eb ("iwlwifi: trans: Clear persistence bit when starting the FW")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This will let us introduce a mechanism to start with rfkill
faked, and put 0 here to override it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add debug prints to the ini flow and rewrite existing prints to provide
more information
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The driver uses msix causes-register to handle both msix and non msix
interrupts when performing sync nmi.  On devices that do not support
msix this register is unmapped and accessing it causes a kernel panic.

Solve this by differentiating the two cases and accessing the proper
causes-register in each case.
Reported-by: NMichal Hocko <mhocko@kernel.org>
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:

	@mmiowb@
	@@
	- mmiowb();

and invoked as:

$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done

NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add a new configuration with a new firmware name for quz devices.
And, since these devices have the same PCI device and subsystem IDs,
we need to add some code to switch from a normal qu firmware to the
quz firmware.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Allows to perform monitor dumping on AX210 device family
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support for radio gf4 (CDB radio).
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Only add the size of the tx command to the dump file size if it is set
in the dump_mask.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

rename few structs to fit the new marketing names
Signed-off-by: NIhab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Allow modules from outside pcie to call sync_nmi.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add a few PCI ID'S for 22000 and killer series in addition to
chainging the marketing name.
Signed-off-by: NIhab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In AX210 family, UMAC periphery address space moved from
0xA00000 to 0xD00000.
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When flushing TX queues no new TX should go into the system.
However, in the following scenario we get TX:
1. Queues are stopped and there are packets in overflow queue
2. Station is removed and flush begins
3. Flush empties space, and reclaim path TXes SKB from overflow
   queue.

Note that the fact the queues are stopped during the process
doesn't matter - the packet will be TXed since the TX path
doesn't care if TX queues are stopped or not, just if there is
space in the queue, which there is, since we just freed a
packet.

A fix here is rather complicated, since the flow is very racy.

Change code not to warn if we are TXing from overflow TX.
In case there is TX from both overflow TX and TX path we will
miss a warning we optimally had, but we can live with that.

Make sure we don't return before overflow queue is empty, otherwise
we will think queues are empty, but they will be refilled, resulting
with assert.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Fixes: 3955525d ("iwlwifi: pcie: buffer packets to avoid overflowing Tx queues")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add new device family AX210.
Make the needed changes for this family.
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The typical sequence of setting INIT_DONE and then waiting
for clock stabilisation is going to need a new workarounds,
so first of all refactor it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Both iwl_trans_fw_error and iwl_force_nmi initiate async recovery flow.
Calling them both is redundant and causing a race.

Solve this by removing the call to iwl_trans_fw_error.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: cfadc3ff ("iwlwifi: pcie: stop the firmware when we restart it")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Implement paging memory dump in the new dump mechanism.
To support this change, moved iwl_self_init_dram strcut from trans_pcie
to trans so that it will accessible via fw_runtime.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Prior to gen2 we allocate the paging memory via alloc_pages
which requires passing ownership on the memory between the
cpu and the device using dma_sync_single_for_cpu and
dma_sync_single_for_device.

Add missing dma_sync_single_for_device in iwl_dump_paging
after copying the memory.

since gen2, we allocate the paging memory using dma_alloc_coherent
which does not need passing ownership between the cpu and device.

Remove unneeded call to dma_sync_single_for_cpu in
iwl_trans_pcie_dump_data prior to copying the memory.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 5538409b ("iwlwifi: pcie: support page dumping in wrt in gen2")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

That's what we pass, and we don't want/need any negative values.
Found by sparse/smatch.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since we use a dumping mask, checking if only monitor was requested
is redundant. Remove the unneeded code.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We don't support 9000 A-step devices anymore, so we can remove the
suspend/resume workaround.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This function was only used by 9000 A-step devices, which we don't
support anymore, so it can be removed.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

One of the cfg struct names is mistakenly "iwl22000", when it should
be "iwl22560".

Chage-Id: If9fbfa4bceef81d028c90c98d47115fbe39da547
Signed-off-by: NIhab Zhaika <ihab.zhaika@intel.com>
Fixes: 2f7a3863 ("iwlwifi: rename the temporary name of A000 to the official 22000")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Some devices with PCI ID 0x2723, which is supposed to be 22260, are
actually not.  So we need to differentiate them by checking the hw_rev
and change the cfg accordingly.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add new structs and PCI IDs for 22260 devices.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Don't populate the array prop on the stack but instead make it static.
Makes the object code smaller by 30 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  80138	  15382	    576	  96096	  17760	drivers/net/wireless/intel/iwlwifi/pcie/trans.o

After:
   text	   data	    bss	    dec	    hex	filename
  79948	  15542	    576	  96066	  17742	drivers/net/wireless/intel/iwlwifi/pcie/trans.o

(gcc version 8.2.0 x86_64)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When ini TLVs are loaded, dump data according to the
stored configuration.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

FW debug data will oneshot read all data available in DRAM
and fill the supplied user buffer. In case the read request
is greater than the new data in DRAM, the driver will write
all data it has and return the buffer immediately.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLior Cohen <lior2.cohen@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We have to choose different configuration and different firmwares
depending on the external RF module that is installed.  Since the
external module is not represented in the PCI IDs, we need to change
the configuration at runtime, after checking the RF ID of the module
installed.  We have a bit of a mess in the code that does this,
because it applies cfg's according to the RF ID only, ignoring the
integrated module that is in use.

Fix that for some devices by adding correct configurations for them
and not ignoring the integrated module's type when making the
decision.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently opmode is limited to asking transport to either
dump all the dumps configured at startup, or monitor only.
Instead, pass to transport a bitmask, to allow flexibility.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The trigger structure is being passed around, when
all we care about is whether to dump only monitor
or not. Pass a bool instead.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>