Use unified lgs8gxx frontend instead of reverse engineered lgs8gl5 frontend.
After this patch, lgs8gl5 frontend could be mark as deprecated.
Future development should base on unified lgs8gxx frontend.
Signed-off-by: NDavid T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Error handling code following a kmalloc should free the allocated data.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NErik Andrén <erik.andren@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

We have support for radio on saa7133/35/31e cards with tda8290/8275(a)
and 5.5MHz ceramic filter on the bridge chips since a while.

It was previously not tested, if this card supports it too, but the old
"ghost" radio with wrong filters doesn't work anymore.

Thanks go to Pham Thanh Nam and Laszlo Kustan for reporting it working
on that input.
Signed-off-by: Nhermann pitton <hermann-pitton@arcor.de>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Define correct tuner in config. Radio now works fine
Signed-off-by: NBeholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The structure and comments of the I2C part have been adopted to fit to the
USB part.

Some additional cleanups and precisements have been made to the version
detection and checking functionality to clearly separate HW/SW/FW version.
Signed-off-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch supports i2c interface of si470x. The i2c specific part
exists in radio-si470x-i2c.c file and the common part uses
radio-si470x-common.c file. The '#if defined' is inserted inevitably
because of parts used only si470x usb in the common file.

The current driver version doesn't support the RDS.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The si470x_disconnect_check is function to check disconnect state of
radio in common file. The function is implemented in each interface
file.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch is for using dev_* macro instead of printk.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch is a preceding work to add the i2c interface of si470x.
The si470x directory includes a common file and usb specific file and
header file.
The part unrelated with usb interface and i2c interface exists in
radio-si470x-common.c file, and The usb specific part exists in
radio-si470x-usb.c file.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
[tobias.lorenz@gmx.net: Small changes, due to new include "linux/smp_lock.h"]
Signed-off-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for the STK7700D USB-DVB-Device.

lsusb identifies it as:
idVendor           0x1164 YUAN High-Tech Development Co., Ltd
idProduct          0x1efc
 iProduct                2 STK7700D

The device is build into a Samsung R55-T5500 notebook.
Signed-off-by: NPete Hildebrandt <send2ph@googlemail.com>
Signed-off-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cinergyInitialize param.flags.
Signed-off-by: NEberhard Mattes <eberhard.mattes@web.de>
Signed-off-by: NThierry MERLE <thierry.merle@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The vidioc_s_std() is not necessary when vdev->tvnorms == 0.
Signed-off-by: NMarton Nemeth <nm127@freemail.hu>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Restructure the UVC descriptors parsing code to handle multiple streaming
interfaces. The driver now creates a uvc_video_chain instance for each chain
detected in the UVC control interface descriptors, and tries to register one
video device per streaming endpoint.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As a first step towards multiple streaming interfaces support, reorganize the
driver's data structures to cleanly separate video control and video streaming
data.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L2 API (chapter 1.5) states that:

	Drivers must implement all input ioctls when the device has one
	or more inputs, all output ioctls when the device has one or more outputs.
	When the device has any audio inputs or outputs the driver must set the
	V4L2_CAP_AUDIO flag in the struct v4l2_capability returned by the
	VIDIOC_QUERYCAP ioctl.

So, devices without audio input should return -EINVAL.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are many lock imbalances in this driver. Fix all found.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There seems to be one superfluos unlock in a poll function. Remove it.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixed the c-qcam source code path in the linux kernel tree.
Signed-off-by: NMhayk Whandson <eu@mhayk.com.br>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The irq handler will touch memory. Even in the error case some URBs may
complete. Thus no memory must be kfreed before all URBs are killed.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for Zilog Z8F0811 IR transceiver chips on
CX2341[68] based boards to ir-kbd-i2c for both the old i2c binding model
and the new i2c binding model.
Signed-off-by: NAndy Walls <awalls@radix.net>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch add support to the cx18 driver for setting up the
Z8F0811/Hauppauge IR Tx/Rx chip with the i2c binding model in newer
kernels.
Signed-off-by: NAndy Walls <awalls@radix.net>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch augments the init data passed by bridge drivers to
ir-kbd-i2c, so that the ir_type can be set explicitly, and so
ir-kbd-i2c internal get_key functions can be reused without
requiring symbols from ir-kbd-i2c in the bridge driver.
Signed-off-by: NAndy Walls <awalls@radix.net>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Functions which are referenced by their address can't be inlined by
definition.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The au0828-dvb driver uses bulk usb transfers for digital transport,
but the debug reports, "iso xfer already running!\n".

Fix this to report bulk instead of isoc.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This prevents a loop if a permanent error occurs in usb_set_interface().
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NDenis Loginov <dinvlad@gmail.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Also, H/V flip default values adjusted according to the webcam IDs.
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The patches
	gspca - vc032x: Add resolution 1280x1024 for sensor mi1310_soc.
	gspca - vc032x: Webcam 041e:405b added and mi1310_soc updated.
will make the preview function not work, so I disable the 1280x1024 resolution
and revert back to the origin mi1310_soc settings.
And, using USB snoop tool on Windows to get the correct i2c commands to
turn on/off the LED flash.
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

* use i2c_w instead of reg_w
* return error on failure
* read the correct number of bytes
Signed-off-by: NBrian Johnson <brijohn@gmail.com>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

After the i2c subdev changes the ordering of initialization changed,
causing a total loss of previous GPIO settings and a loss of DTV.
The generic firmware loading routine has now changed to preserve
GPIO values if the device is cx23885 based (safety) and I've
moved the GPIO configuration from probe() into the cx23885 init
func which is a little clearer and fixes the bug.
Tested-by: NSohail Syyed <linuxtv@hubstar.net>
Reviewed-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NSteven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Even devices without ac97 needs to call analog audio setup function, to
properly set xclk and mute/unmute.

Thanks to Angelo Cano <acano@fastmail.fm> for reporting and testing it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is no point in defining I2C adapter IDs when no code is using
them. As this field might go away in the future, stop using it when
we don't need to.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replace printing to magically sized temporary buffer with use
of KERN_CONT for continual printing of eeprom registers dump.

Since deb_info is defined as dprintk, which is conditionally defined
to printk without additional parameters, meaning that deb_info is equivalent
to direct printk (without adding KERN_ facility), we can use KERN_DEBUG and
KERN_CONT in there, eliminating the need for sprintf into temporary buffer
with not easily readable/magical size.

Though it's strange, that deb_info definition uses printk without KERN_
facility and callers don't use it either.
Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove the subdev_s_std() method from the GPIO subdev.  It appears it was
used in the past to effect the switch back from radio mode to tuner mode,
but it had a side effect that is improper and against the V4L2 spec, when
you were not in radio mode.  Whenever the video stanadrd was changed, the
GPIO audio mux was set back to the tuner audio input, even if you were set
to a Line In input.

Thanks to Ravi A. for doing the troubleshooting to point me right to the
problem.
Reported-by: NRavi A <asvravi@gmail.com>
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tested-by: NRavi A. <asvravi@gmail.com>
Signed-off-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>