Add support for input supply in DT parsing of node.
The input supply will be provided by the property
"vin-supply" in the regulator node.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It is very common for regulators to support having their enable signal
controlled by a GPIO. Since there are a bunch of fiddly things to get
right like handling the operations when the enable signal is tied to
a rail and it's just replicated code add support for this to the core.

Drivers should set ena_gpio in their config if they have a GPIO control,
using ena_gpio_flags to specify any flags (including GPIOF_OUT_INIT_ for
the initial state) and ena_gpio_invert if the GPIO is active low. The
core will then override any enable and disable operations the driver has
and instead control the specified GPIO.

This will in the future also allow us to further extend the core by
identifying when several enable signals have been tied together and
handling this properly.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Many regulators have a fixed specification for their enable time. Allow
this to be set in the regulator_desc as a number to save them having to
implement an explicit operation.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Convert tps65217_pmic_ldo1_ops to use regulator_list_voltage_table.

We have n_voltages and volt_table settings in regulator_desc,
so we don't need the table and table_len fields in struct tps_info.
Thus remove them from struct tps_info.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix kernel-doc warning.  This struct member was removed in commit
87568264 ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.

  Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 2603efa3 ("bug.h: Fix up powerpc build regression") corrected
the powerpc build case and extended the __ASSEMBLY__ guards, but it also
got caught in pre-processor hell accidentally matching the else case of
CONFIG_BUG resulting in the BUG disabled case tripping up on
-Werror=implicit-function-declaration.

It's not possible to __ASSEMBLY__ guard the entire file as architecture
code needs to get at the BUGFLAG_WARNING definition in the GENERIC_BUG
case, but the rest of the CONFIG_BUG=y/n case needs to be guarded.

Rather than littering endless __ASSEMBLY__ checks in each of the if/else
cases we just move the BUGFLAG definitions up under their own
GENERIC_BUG test and then shove everything else under one big
__ASSEMBLY__ guard.

Build tested on all of x86 CONFIG_BUG=y, CONFIG_BUG=n, powerpc (due to
it's dependence on BUGFLAG definitions in assembly code), and sh (due to
not bringing in linux/kernel.h to satisfy the taint flag definitions used
by the generic bug code).

Hopefully that's the end of the corner cases and I can abstain from ever
having to touch this infernal header ever again.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Tested-by: NFengguang Wu <wfg@linux.intel.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly.  They
report bogus sizes, in some cases becoming unusable as a result.

The bugs were triggered by commit
09b6b51b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices.  By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.

It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly.  Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.

Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device.  If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.

This fixes Bugzilla #43391.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NHans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This comment is well out of date.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Guard vga_switcheroo.h against multiple inclusion.
Signed-off-by: NOzan Çağlayan <ozancag@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company.  Replace ST's id with viresh.linux@gmail.com.

It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: NViresh Kumar <viresh.linux@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the x86 32bit PAE CONFIG_TRANSPARENT_HUGEPAGE=y case while holding the
mmap_sem for reading, cmpxchg8b cannot be used to read pmd contents under
Xen.

So instead of dealing only with "consistent" pmdvals in
pmd_none_or_trans_huge_or_clear_bad() (which would be conceptually
simpler) we let pmd_none_or_trans_huge_or_clear_bad() deal with pmdvals
where the low 32bit and high 32bit could be inconsistent (to avoid having
to use cmpxchg8b).

The only guarantee we get from pmd_read_atomic is that if the low part of
the pmd was found null, the high part will be null too (so the pmd will be
considered unstable).  And if the low part of the pmd is found "stable"
later, then it means the whole pmd was read atomically (because after a
pmd is stable, neither MADV_DONTNEED nor page faults can alter it anymore,
and we read the high part after the low part).

In the 32bit PAE x86 case, it is enough to read the low part of the pmdval
atomically to declare the pmd as "stable" and that's true for THP and no
THP, furthermore in the THP case we also have a barrier() that will
prevent any inconsistent pmdvals to be cached by a later re-read of the
*pmd.
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Tested-by: NAndrew Jones <drjones@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On arches that do not support this_cpu_cmpxchg_double() slab_lock is used
to do atomic cmpxchg() on double word which contains page->_count.  The
page count can be changed from get_page() or put_page() without taking
slab_lock.  That corrupts page counter.

Fix it by moving page->_count out of cmpxchg_double data.  So that slub
does no change it while updating slub meta-data in struct page.

[akpm@linux-foundation.org: use standard comment layout, tweak comment text]
Reported-by: NAmey Bhide <abhide@nicira.com>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NChristoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver supports TI/National LP8720, LP8725 PMIC.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The S5M8767A can't know status of ap reset.
So, After AP watchdog reset, AP can't boot normally.

Problem can be happened like below condition.
- AP Bootable lowest voltage(vdd_arm): 0.9v
- AP DVFS voltage table: 0.8v, 0.9v, 1.0v
- During AP works on lowest voltage(0.8V), watchdog reset is asserted
- AP can't boot, because vdd arm is still 0.8v

Solution
- Basic concept:
  After ap watchdog reset, GPIO configuration is changed by default value
- S5M8767A has function of voltage control with gpio (8 levels with 3 gpios)
- Set bootable voltage on level 0 -> can work with default gpio configuration
- In the probing, Change voltage control level from level 0 to level 1
- Execute normal dvfs operation on level 1
- After watchdog reset, ap gpio is set by default value
- PMIC operation mode is changed by ap reset (level1 -> level0)
- Regardless of previous vdd_arm voltage, AP always can be booted.
Signed-off-by: NSangbeom Kim <sbkim73@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NKay Sievers <kay@vrfy.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The asm-generic/bug.h __ASSEMBLY__ guarding is completely bogus, which
tripped up the powerpc build when the kernel.h include was added:

	In file included from include/asm-generic/bug.h:5:0,
			 from arch/powerpc/include/asm/bug.h:127,
			 from arch/powerpc/kernel/head_64.S:31:
	include/linux/kernel.h:44:0: warning: "ALIGN" redefined [enabled by default]
	include/linux/linkage.h:57:0: note: this is the location of the previous definition
	include/linux/sysinfo.h: Assembler messages:
	include/linux/sysinfo.h:7: Error: Unrecognized opcode: `struct'
	include/linux/sysinfo.h:8: Error: Unrecognized opcode: `__kernel_long_t'

Moving the __ASSEMBLY__ guard up and stashing the kernel.h include under
it fixes this up, as well as covering the case the original fix was
attempting to handle.
Tested-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 5963e317 ("ftrace/x86: Do not change stacks in DEBUG when
calling lockdep") prevented lockdep calls from the int3 breakpoint handler
from reseting the stack if a function that was called was in the process
of being converted for tracing and had a breakpoint on it. The idea is,
before calling the lockdep code, do a load_idt() to the special IDT that
kept the breakpoint stack from reseting. This worked well as a quick fix
for this kernel release, until a certain config caused a lockup in the
function tracer start up tests.

Investigating it, I found that the load_idt that was used to prevent
the int3 from changing stacks was itself being traced!

Even though the config had CONFIG_OPTIMIZE_INLINING disabled, and
all 'inline' tags were set to always inline, there were still cases that
it did not inline! This was caused by CONFIG_PARAVIRT_GUEST, where it
would add a pointer to the native_load_idt() which made that function
to be traced.

Commit 45959ee7 ("ftrace: Do not function trace inlined functions")
only touched the 'inline' tags when CONFIG_OPMITIZE_INLINING was enabled.
PARAVIRT_GUEST shows that this was not enough and we need to also
mark always_inline with notrace as well.
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Tested-by: NFengguang Wu <wfg@linux.intel.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Currently there is a 'chicken and egg' issue when the DS is also the mounted
MDS. The nfs_match_client() reference from nfs4_set_ds_client bumps the
cl_count, the nfs_client is not freed at umount, and nfs4_deviceid_purge_client
is not called to dereference the MDS usage of a deviceid which holds a
reference to the DS nfs_client.  The result is the umount program returns,
but the nfs_client is not freed, and the cl_session hearbeat continues.

The MDS (and all other nfs mounts) lose their last nfs_client reference in
nfs_free_server when the last nfs_server (fsid) is umounted.
The file layout DS lose their last nfs_client reference in destroy_ds
when the last deviceid referencing the data server is put and destroy_ds is
called. This is triggered by a call to nfs4_deviceid_purge_client which
removes references to a pNFS deviceid used by an MDS mount.

The fix is to track how many pnfs enabled filesystems are mounted from
this server, and then to purge the device id cache once that count reaches
zero.
Reported-by: NJorge Mora <Jorge.Mora@netapp.com>
Reported-by: NAndy Adamson <andros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

This change makes it possible to set ramp_delay with 0.xxx mV/uS without
truncation issue.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NRémi Denis-Courmont <remi@remlab.net>
Cc: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some hardwares ramp_delay for BUCKs is a configurable parameter which can
be configured through DT or board file.This patch adds ramp_delay to regulator
constraints and allow user to configure it for regulators which supports this
feature, through DT or board file. It will provide two ways of setting the
ramp_delay for a regulator:
	First, by setting it as constraints in board file(for configurable
regulators) and set_machine_constraints() will take care of setting it on
hardware by calling(the provided) .set_ramp_delay() operation(callback).
	Second, by setting it as data in regulator_desc(as fixed/default
ramp_delay rate) for a regulator in driver.

regulator_set_voltage_time_sel() will give preference to
constraints->ramp_delay while reading ramp_delay rate for regulator. Similarly
users should also take care accordingly while refering ramp_delay rate(in case
of implementing their private .set_voltage_time_sel() callbacks for different
regulators).

[Rewrote subject for 80 columns -- broonie]
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix warnings on some architectures/configs (not on x86):

include/linux/vga_switcheroo.h:28:30: warning: 'struct pci_dev' declared inside parameter list [enabled by default]
include/linux/vga_switcheroo.h:28:30: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc:	Takashi Iwai <tiwai@suse.de>
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 2a0c451a.

It causes crashes, because now ip6_null_entry is used before
it is initialized.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minchan Kim reports that when a system has many swap areas, and tmpfs
swaps out to the ninth or more, shmem_getpage_gfp()'s attempts to read
back the page cannot locate it, and the read fails with -ENOMEM.

Whoops.  Yes, I blindly followed read_swap_header()'s pte_to_swp_entry(
swp_entry_to_pte()) technique for determining maximum usable swap
offset, without stopping to realize that that actually depends upon the
pte swap encoding shifting swap offset to the higher bits and truncating
it there.  Whereas our radix_tree swap encoding leaves offset in the
lower bits: it's swap "type" (that is, index of swap area) that was
truncated.

Fix it by reducing the SWP_TYPE_SHIFT() in swapops.h, and removing the
broken radix_to_swp_entry(swp_to_radix_entry()) from read_swap_header().

This does not reduce the usable size of a swap area any further, it
leaves it as claimed when making the original commit: no change from 3.0
on x86_64, nor on i386 without PAE; but 3.0's 512GB is reduced to 128GB
per swapfile on i386 with PAE.  It's not a change I would have risked
five years ago, but with x86_64 supported for ten years, I believe it's
appropriate now.

Hmm, and what if some architecture implements its swap pte with offset
encoded below type? That would equally break the maximum usable swap
offset check.  Happily, they all follow the same tradition of encoding
offset above type, but I'll prepare a check on that for next.
Reported-and-Reviewed-and-Tested-by: NMinchan Kim <minchan@kernel.org>
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org [3.1, 3.2, 3.3, 3.4]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

/proc/net/ipv6_route reflects the contents of fib_table_hash. The proc
handler is installed in ip6_route_net_init() whereas fib_table_hash is
allocated in fib6_net_init() _after_ the proc handler has been installed.

This opens up a short time frame to access fib_table_hash with its pants
down.

fib6_init() as a whole can't be moved to an earlier position as it also
registers the rtnetlink message handlers which should be registered at
the end. Therefore split it into fib6_init() which is run early and
fib6_init_late() to register the rtnetlink message handlers.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Reviewed-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Orphaning skb in dev_hard_start_xmit() makes bonding behavior
unfriendly for applications sending big UDP bursts : Once packets
pass the bonding device and come to real device, they might hit a full
qdisc and be dropped. Without orphaning, the sender is automatically
throttled because sk->sk_wmemalloc reaches sk->sk_sndbuf (assuming
sk_sndbuf is not too big)

We could try to defer the orphaning adding another test in
dev_hard_start_xmit(), but all this seems of little gain,
now that BQL tends to make packets more likely to be parked
in Qdisc queues instead of NIC TX ring, in cases where performance
matters.

Reverts commits :
fc6055a5 net: Introduce skb_orphan_try()
87fd308c net: skb_tx_hash() fix relative to skb_orphan_try()
and removes SKBTX_DRV_NEEDS_SK_REF flag
Reported-and-bisected-by: NJean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide an iterator to receive the log buffer content, and convert all
kmsg_dump() users to it.

The structured data in the kmsg buffer now contains binary data, which
should no longer be copied verbatim to the kmsg_dump() users.

The iterator should provide reliable access to the buffer data, and also
supports proper log line-aware chunking of data while iterating.
Signed-off-by: NKay Sievers <kay@vrfy.org>
Tested-by: NTony Luck <tony.luck@intel.com>
Reported-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Tested-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A handy function that we will use outside of ram_core soon. But
so far just factor it out and start using it in post_init().
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Without the update, we'll only see the new dmesg buffer after the
reboot, but previously we could see it right away. Making an oops
visible in pstore filesystem before reboot is a somewhat dubious
feature, but removing it wasn't an intentional change, so let's
restore it.

For this we have to make persistent_ram_save_old() safe for calling
multiple times, and also extern it.
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

A similar patch has already been applied as commit
151b6128 (USB: EHCI: fix crash during
suspend on ASUS computers).  The patch supersedes that one and reverts
it.  There are two differences:

	The old patch added the flag at the USB level; this patch
	adds it at the PCI level.

	The old patch applied to all chipsets with the same vendor,
	subsystem vendor, and product IDs; this patch makes an
	exception for a known-good system (based on DMI information).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NDâniel Fraga <fragabr@gmail.com>
Tested-by: NAndrey Rahmatullin <wrar@wrar.name>
Tested-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch converts .is_enabled and .get_voltage_sel to
regulator_is_enabled_regmap and regulator_get_voltage_sel_regmap.

For .enable, .disable, and .set_voltage_sel, the write protect level is either
1 or 2. So we cannot use regulator_[enable|disable|set_voltage_sel]_regmap.

Now we store the enable reg/mask and vsel reg/mask in regulator_desc,
so we can remove enable_mask, set_vout_reg, and set_vout_mask from
struct tps_info.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds an optional target_core_fabric_ops->put_session() caller
within the existing target_put_session() code path.

This is required by tcm_qla2xxx code in order to invoke it's own fabric
specific session shutdown handler using se_session->sess_kref.
Signed-off-by: NJoern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping.  This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.

When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit.  In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.

Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping.  In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.

If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)

This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :

netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.

Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.

Based on a previous patch from Tom Herbert.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NTom Herbert <therbert@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before Kernel 3.5, no one was checking for the return value of
drm_connector_attach_property, so we never noticed that we were unable
to create some properties. Commit "drm: WARN() when
drm_connector_attach_property fails" added a WARN when we fail to
create a property, and the transition from "connector properties" to
"object properties" changed the warning message a little bit.

On i915 machines with many TV connectors we hit the maximum number of
properties (since each TV connector uses a lot of properties), so we
get a few backtraces in our logs. This commit increases the maximum
number of properties to 24 hoping we'll have enough room for
everybody.

Chris suggested that we convert this code to "lists", but I believe
this conversion can come after we make sure people's dmesgs are not
spammed by our driver.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reported-by: NDave Jones <davej@redhat.com>
Tested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Before this patch the owner field of the /dev/radio# device fops was set to
the snd-tea575x-tuner module itself. Meaning that the module which was using
it could be rmmod-ed while the device is open, and then BAD things happen.

I know, as I found out the hard way :)

Note that there is no need to also somehow increase the refcount of the
snd-tea575x-tuner module itself, since any drivers using it will have
symbolic references to it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
CC: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Yuck. The VIDIOC_(TRY_)DECODER_CMD ioctls already had ioctl numbers 96 and 97,
and after merging the timings API I forgot to continue numbering from 98. So
now we have two ioctls with number 96 and two with 97.

With the new table-driver ioctl handling in v4l2-ioctl.c it is essential that
each ioctl has its own unique number, so let's fix this quickly for 3.5.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If I build with W=1, for every file that includes <net/route.h>, I get the warning

    include/net/route.h: In function 'ip_route_output':
    include/net/route.h:135:3: warning: initialized field overwritten [-Woverride-init]
    include/net/route.h:135:3: warning: (near initialization for 'fl4') [-Woverride-init]

(This is with "gcc (Debian 4.6.3-1) 4.6.3")

A fix seems pretty trivial: move the initialization of .flowi4_tos
earlier.  As far as I can tell, this has no effect on code generation.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

asm-generic/bug.h uses taint flags that are only defined in
linux/kernel.h, resulting in build failures on platforms that
don't include linux/kernel.h some other way:

        arch/sh/include/asm/thread_info.h:172:2: error: 'TAINT_WARN' undeclared (first use in this function)

Caused by commit edd63a27 ("set_restore_sigmask() is never called
without SIGPENDING (and never should be)").
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

pxa-ssp.c uses API like cpu_is_pxa3xx(), cpu_is_pxa2xx(), which is
defined under arch-pxa architecture, and drivers under mach-mmp
can't find it. so just use ssp->type to replace that API.
Signed-off-by: NQiao Zhou <zhouqiao@marvell.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

add pxa910-ssp into ssp_id_table, and fix pxa-ssp compiling issue
under mach-mmp architect.
Signed-off-by: NQiao Zhou <zhouqiao@marvell.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>