Only set extended scan response only when it exists. Otherwise, clear
the scan response data.

Per the core spec v5.2, Vol 4, Part E, 7.8.55

If the advertising set is non-scannable and the Host uses this command
other than to discard existing data, the Controller shall return the
error code Invalid HCI Command Parameters (0x12).

On WCN3991, the controller correctly responds with Invalid Parameters
when this is sent.  That error causes __hci_req_hci_power_on to fail
with -EINVAL and LE devices can't connect because background scanning
isn't configured.

Here is an hci trace of where this issue occurs during power on:

< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
        Handle: 0x00
        Properties: 0x0010
          Use legacy advertising PDUs: ADV_NONCONN_IND
        Min advertising interval: 181.250 msec (0x0122)
        Max advertising interval: 181.250 msec (0x0122)
        Channel map: 37, 38, 39 (0x07)
        Own address type: Random (0x01)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Filter policy: Allow Scan Request from Any, Allow Connect...
        TX power: 127 dbm (0x7f)
        Primary PHY: LE 1M (0x01)
        Secondary max skip: 0x00
        Secondary PHY: LE 1M (0x01)
        SID: 0x00
        Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
      LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
        Status: Success (0x00)
        TX power (selected): 9 dbm (0x09)
< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
        Advertising handle: 0x00
        Advertising random address: 08:FD:55:ED:22:28 (OUI 08-FD-55)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Advertising Set Random Address (0x08|0x0035) ncmd
        Status: Success (0x00)
< HCI Command: LE Set Extended Scan Response Data (0x08|0x0038) plen 35
        Handle: 0x00
        Operation: Complete scan response data (0x03)
        Fragment preference: Minimize fragmentation (0x01)
        Data length: 0x0d
        Name (short): Chromebook
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Response Data (0x08|0x0038) ncmd 1
        Status: Invalid HCI Command Parameters (0x12)
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: NDaniel Winkler <danielwinkler@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When an LE connection is requested and an RPA update is needed via
hci_connect_le_scan, the default scanning parameters are used rather
than the connect parameters.  This leads to significant delays in the
connection establishment process when using lower duty cycle scanning
parameters.

The patch simply looks at the pended connection list when trying to
determine which scanning parameters should be used.

Before:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
                            #378 [hci0] 1659.247156
        Own address type: Public (0x00)
        Filter policy: Ignore not in white list (0x01)
        PHYs: 0x01
        Entry 0: LE 1M
          Type: Passive (0x00)
          Interval: 367.500 msec (0x024c)
          Window: 37.500 msec (0x003c)

After:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
                               #39 [hci0] 7.422109
        Own address type: Public (0x00)
        Filter policy: Ignore not in white list (0x01)
        PHYs: 0x01
        Entry 0: LE 1M
          Type: Passive (0x00)
          Interval: 60.000 msec (0x0060)
          Window: 60.000 msec (0x0060)
Signed-off-by: NAlain Michaud <alainm@chromium.org>
Reviewed-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: NYu Liu <yudiliu@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support to enable the use of RPA Address resolution
using expermental feature mgmt command.
Signed-off-by: NSathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In this patch if le_create_conn process is started restrict to
disable address resolution and same is disabled during
le_enh_connection_complete
Signed-off-by: NSathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When address resolution is enabled and set_privacy is enabled let's
use own address type as 0x03
Signed-off-by: NSathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the whitelist is updated, then also update the entries of the
resolving list for devices where IRKs are available.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the LL Privacy support is available, then as part of enabling or
disabling passive background scanning, it is required to set up the
controller based address resolution as well.

Since only passive background scanning is utilizing the whitelist, the
address resolution is now bound to the whitelist and passive background
scanning. All other resolution can be easily done by the host stack.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add functionality to disable and remove advertising instances,
and use that functionality in MGMT add/remove advertising calls.

Currently, advertising is globally-disabled, i.e. all instances are
disabled together, even if hardware offloading is available. This
patch adds functionality to disable and remove individual adv
instances, solving two issues:

1. On new advertisement registration, a global disable was done, and
then only the new instance was enabled. This meant only the newest
instance was actually enabled.

2. On advertisement removal, the structure was removed, but the instance
was never disabled or removed, which is incorrect with hardware offload
support.
Signed-off-by: NDaniel Winkler <danielwinkler@google.com>
Reviewed-by: NShyh-In Hwang <josephsih@chromium.org>
Reviewed-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Even with one advertisement monitor in place, the scan policy should use
the whitelist while the system is going to suspend to prevent waking by
random advertisement.

The following test was performed.
- With a paired device, register one advertisement monitor, suspend
the system and verify that the host was not awaken by random
advertisements.
Signed-off-by: NMiao-chen Chou <mcchou@chromium.org>
Reviewed-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fixes active scans to use the configured default parameters.
Signed-off-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When restarting LE scanning, check if it's currently paused before
enabling passive scanning.
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the extended advertisement feature is enabled, a hardcoded min and
max interval of 0x8000 is used.  This patch fixes this issue by using
the configured min/max value.

This was validated by setting min/max in main.conf and making sure the
right setting is applied:

< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen
25                                          #93 [hci0] 10.953011
…
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
…
Signed-off-by: NAlain Michaud <alainm@chromium.org>
Reviewed-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: NDaniel Winkler <danielwinkler@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This calls hci_update_background_scan() when there is any update on the
advertisement monitors. If there is at least one advertisement monitor,
the filtering policy of scan parameters should be 0x00. This also reports
device found mgmt events if there is at least one monitor.

The following cases were tested with btmgmt advmon-* commands.
(1) add a ADV monitor and observe that the passive scanning is
triggered.
(2) remove the last ADV monitor and observe that the passive scanning is
terminated.
(3) with a LE peripheral paired, repeat (1) and observe the passive
scanning continues.
(4) with a LE peripheral paired, repeat (2) and observe the passive
scanning continues.
(5) with a ADV monitor, suspend/resume the host and observe the passive
scanning continues.
Signed-off-by: NMiao-chen Chou <mcchou@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Replace the wakeable boolean with flags in hci_conn_params and all users
of this boolean. This will be used by the get/set device flags mgmt op.
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Since the classic device list now supports flags, convert the wakeable
list into a flag on the existing device list.
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch centralized the initialization of default parameters.  This
is required to allow clients to more easily customize the default
system parameters.
Signed-off-by: NAlain Michaud <alainm@chromium.org>
Reviewed-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Check current scan state by checking HCI_LE_SCAN flag and send scan
disable command only if scan is already enabled.
Signed-off-by: NManish Mandlik <mmandlik@google.com>
Reviewed-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Renamed BT_SUSPEND_COMPLETE to BT_SUSPEND_CONFIGURE_WAKE since it sets
up the event filter and whitelist for wake-up.
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When a device is suspended, it doesn't need to be as responsive to
connection events. Increase the interval to 640ms (creating a duty cycle
of roughly 1.75%) so that passive scanning uses much less power (vs
previous duty cycle of 18.75%). The new window + interval combination
has been tested to work with HID devices (which are currently the only
devices capable of wake up).
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The types for window and interval should be uint16, not uint8.
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch fix the advertising handle is set to 0 regardless of actual
instance value. The affected commands are LE Set Advertising Set Random
Address, LE Set Extended Advertising Data, and LE Set Extended Scan
Response Data commands.
Signed-off-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When starting active scanning for discovery the whitelist is not needed
to be used. So the filter_policy is 0x00. To make the core more readable
use a variable name instead of just setting 0 as paramter.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

BlueZ cancels adv when starting a scan, but does not cancel a scan when
starting to adv. Neither is required, so this brings both to a
consistent state (of not affecting each other). Some very rare (I've
never seen one) BT 4.0 chips will fail to do both at once. Even this is
ok since the command that will fail will be the second one, and thus the
common sense logic of first-come-first-served is preserved for BLE
requests.
Signed-off-by: NDmitry Grinberg <dmitrygr@google.com>
Signed-off-by: NManish Mandlik <mmandlik@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To prevent spurious wake ups, we disable any discovery or advertising
when we enter suspend and restore it when we exit suspend. While paused,
we disable any management requests to modify discovery or advertising.
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To handle LE devices, we must first disable passive scanning and
disconnect all connected devices. Once that is complete, we update the
whitelist and re-enable scanning
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To handle BR/EDR devices, we first disable page scan and disconnect all
connected devices. Once that is complete, we add event filters (for
devices that can wake the system) and re-enable page scan.
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Register for PM_SUSPEND_PREPARE and PM_POST_SUSPEND to make sure the
Bluetooth controller is prepared correctly for suspend/resume. Implement
the registration, scheduling and task handling portions only in this
patch.
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the RPA generation fails, indicate the error with a device specifc
error message.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Instances may have flags set as part of its data in which case the code
should not attempt to add it again otherwise it can cause duplication:

< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35
        Handle: 0x00
        Operation: Complete extended advertising data (0x03)
        Fragment preference: Minimize fragmentation (0x01)
        Data length: 0x06
        Flags: 0x04
          BR/EDR Not Supported
        Flags: 0x06
          LE General Discoverable Mode
          BR/EDR Not Supported
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Instance 0 is controlled by stack itself and always set the local name
in the scan response.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When using LE Set Extended Advertising Enable command the duration
refers to the lifetime of instance not the length which is actually
controlled by the interval_min and interval_max when setting the
parameters.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Changes made to add support for fast advertising interval
as per core 4.1 specification, section 9.3.11.2.

A peripheral device entering any of the following GAP modes and
sending either non-connectable advertising events or scannable
undirected advertising events should use adv_fast_interval2
(100ms - 150ms) for adv_fast_period(30s).

         - Non-Discoverable Mode
         - Non-Connectable Mode
         - Limited Discoverable Mode
         - General Discoverable Mode
Signed-off-by: NSpoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This makes use of controller sets when using Extended Advertising
feature thus offloading the scheduling to the controller.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.

The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.

This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.

Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64)                                  0.352340
= Note: Bluetooth subsystem version 2.22                               0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0)               [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84                                 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm)                      [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14             {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14                  {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14                {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1       {0x0003} [hci0] 27.302310
        Address type: 0x06
          LE Public
          LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6   #1 [hci0] 27.302496
        Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4                 #2 [hci0] 27.419117
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7  #3 [hci0] 27.419244
        Type: Active (0x01)
        Interval: 11.250 msec (0x0012)
        Window: 11.250 msec (0x0012)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #4 [hci0] 27.420131
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2      #5 [hci0] 27.420259
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                 #6 [hci0] 27.420969
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #7 [hci0] 27.421983
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4        {0x0003} [hci0] 27.422059
      Start Discovery (0x0023) plen 1
        Status: Success (0x00)
        Address type: 0x06
          LE Public
          LE Random
@ MGMT Event: Discovering (0x0013) plen 2             {0x0003} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0002} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0001} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Trivial fix to clean up an indentation issue
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for advertising in primary and secondary
channel on different PHYs. User can add the phy preference in
the flag based on which phy type will be added in extended
advertising parameter would be set.

@ MGMT Command: Add Advertising (0x003e) plen 11
        Instance: 1
        Flags: 0x00000200
          Advertise in CODED on Secondary channel
        Duration: 0
        Timeout: 0
        Advertising data length: 0
        Scan response length: 0
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2
        Extended advertising: Disabled (0x00)
        Number of sets: Disable all sets (0x00)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
        Handle: 0x00
        Properties: 0x0000
        Min advertising interval: 1280.000 msec (0x0800)
        Max advertising interval: 1280.000 msec (0x0800)
        Channel map: 37, 38, 39 (0x07)
        Own address type: Random (0x01)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
        TX power: 127 dbm (0x7f)
        Primary PHY: LE Coded (0x03)
        Secondary max skip: 0x00
        Secondary PHY: LE Coded (0x03)
        SID: 0x00
        Scan request notifications: Disabled (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This basically sets the random address for the adv instance
Random address can be set only if the instance is created which
is done in Set ext adv param.

Random address and rpa expire timer and flags have been added
to adv instance which will be used when the respective
instance is scheduled.

This introduces a hci_get_random_address() which returns the
own address type and random address (rpa or nrpa) based
on the instance flags and hdev flags. New function is required
since own address type should be known before setting adv params
but address can be set only after setting params.

< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
        Advertising handle: 0x00
        Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If ext adv is enabled then use ext adv to disable as well.
Also remove the adv set during LE disable.

< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2
        Extended advertising: Disabled (0x00)
        Number of sets: Disable all sets (0x00)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch implements Set Ext Adv data and Set Ext Scan rsp data
if controller support extended advertising.

Currently the operation is set as Complete data and fragment
preference is set as no fragment

< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35
        Handle: 0x00
        Operation: Complete extended advertising data (0x03)
        Fragment preference: Minimize fragmentation (0x01)
        Data length: 0x15
        16-bit Service UUIDs (complete): 2 entries
          Heart Rate (0x180d)
          Battery Service (0x180f)
        Name (complete): Test LE
        Company: Google (224)
          Data: 0102
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Data (0x08|0x0037) ncmd 1
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch basically replaces legacy adv with extended adv
based on the controller support. Currently there is no
design change. ie only one adv set will be enabled at a time.

This also adds tx_power in instance and store whatever returns
from Set_ext_parameter, use the same in adv data as well.
For instance 0 tx_power is stored in hdev only.

< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
        Handle: 0x00
        Properties: 0x0010
          Use legacy advertising PDUs: ADV_NONCONN_IND
        Min advertising interval: 1280.000 msec (0x0800)
        Max advertising interval: 1280.000 msec (0x0800)
        Channel map: 37, 38, 39 (0x07)
        Own address type: Random (0x01)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
        TX power: 127 dbm (0x7f)
        Primary PHY: LE 1M (0x01)
        Secondary max skip: 0x00
        Secondary PHY: LE 1M (0x01)
        SID: 0x00
        Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
      LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
        Status: Success (0x00)
        TX power (selected): 7 dbm (0x07)
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6
        Extended advertising: Enabled (0x01)
        Number of sets: 1 (0x01)
        Entry 0
          Handle: 0x00
          Duration: 0 ms (0x00)
          Max ext adv events: 0
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>