Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 06 10月, 2008 4 次提交
    • H
      atmel-mci: Platform code for supporting multiple mmc slots · 6b918657
      由 Haavard Skinnemoen 提交于 
      Add the necessary platform infrastructure to support multiple mmc/sdcard
slots all at once through a single controller. Currently, the driver
will use the first valid slot it finds and stick with that, but later
patches will add support for switching between several slots on the fly.

Extend the platform data structure with per-slot information: MMC/SDcard
bus width and card detect/write protect pins. This will affect the pin
muxing as well as the capabilities announced to the mmc core.

Note that board code is now required to supply a mci_platform_data
struct to at32_add_device_mci().
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
      6b918657
    • H
      atmel-mci: Don't stop the clock between transfers · 945533b5
      由 Haavard Skinnemoen 提交于 
      Some cards might get upset if we turn off the clock for extended periods
of time. So keep the clock running until the mmc core tells us to turn
it off.

Also, don't reset the controller between each transfer. That was an
attempt to work around earlier bugs, and it never really worked very
well.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
      945533b5
    • H
      atmel-mci: Implement tasklet as a state machine · c06ad258
      由 Haavard Skinnemoen 提交于 
      With the current system of completed/pending events, things may get
handled in different order depending on which event triggers first. For
example, if the data transfer is complete before the command, the stop
command must be sent after the command is complete, not the data. This
creates a bit of complexity around the stop command.

By having the tasklet go through a sequence of clearly defined states,
things always happen in a certain order even if the events come at
different times, so the stop command can simply be sent when we exit the
"sending data" state because we will never enter that state before the
command has been sent successfully.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
      c06ad258
    • H
      atmel-mci: Initialize BLKR before sending data transfer command · a252e3e3
      由 Haavard Skinnemoen 提交于 
      The atmel-mci driver sometimes fails data transfers like this:

   mmcblk0: error -5 transferring data
   end_request: I/O error, dev mmcblk0, sector 2749769
   end_request: I/O error, dev mmcblk0, sector 2749777

It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.

This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Reported-by: NHein_Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
      a252e3e3
  3. 05 10月, 2008 2 次提交
  5. 04 10月, 2008 27 次提交
  7. 03 10月, 2008 7 次提交