Replace individual implementations with the recently introduced
skb_postpush_rcsum() helper.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NTom Herbert <tom@herbertland.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 2b2427d0 ("phy: micrel: Add ethtool statistics counters")
from Dec 30, 2015, leads to the following static checker
warning:

        drivers/net/phy/micrel.c:609 kszphy_get_stat()
        warn: unsigned 'val' is never less than zero.

drivers/net/phy/micrel.c
   602  static u64 kszphy_get_stat(struct phy_device *phydev, int i)
   603  {
   604          struct kszphy_hw_stat stat = kszphy_hw_stats[i];
   605          struct kszphy_priv *priv = phydev->priv;
   606          u64 val;
   607
   608          val = phy_read(phydev, stat.reg);
   609          if (val < 0) {
                    ^^^^^^^
Unpossible!

   610                  val = UINT64_MAX;
   611          } else {
   612                  val = val & ((1 << stat.bits) - 1);
   613                  priv->stats[i] += val;
   614                  val = priv->stats[i];
   615          }
   616
   617          return val;
   618  }

The same problem exists in the Marvell driver. Fix both.

Fixes: 2b2427d0 ("phy: micrel: Add ethtool statistics counters")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reported-by: NJulia.Lawall <julia.lawall@lip6.fr>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kan Liang says:

====================
ethtool per queue parameters support

Modern network interface controllers usually support multiple receive
and transmit queues. Each queue may have its own parameters. For
example, Intel XL710/X710 hardware supports per queue interrupt
moderation. However, current ethtool does not support per queue
parameters option. User has to set parameters for the whole NIC.
This series extends ethtool to support per queue parameters option.

Since the support of per queue parameters vary with different cards,
it is impossible to address all cards in one patch. This series only
supports per queue coalesce options on i40e driver. The framework used
in the patch can be easily extended to other cards and parameters.

The lib bitmap needs to be extended to facilitate exchanging queue bitmaps
between user space and kernel space. Two patches from David's latest V8
patch series are also cited in this series. You may refer to
https://lkml.org/lkml/2016/2/9/919 for more details.

Changes since V6:
 - Rebase on commit 76d13b56. Did minor change in patch 6.

Changes since V5:
 - Add test_bitmap.c and bitmap.sh in the series. They are forgot
   to be added previously.
 - Update the first two patches to David's latest V8 version. The changes
   include
      - bitmap u32 API returns number of bits copied, unit tests updated
      - module_exit in test_bitmap
 - Also change the mode of bitmap.sh to 755 according to Ben's suggestion

Changes since V4:
 - Modify set/get_per_queue_coalesce function description
 - Change the queue number to be u32
 - Correct an error of calculating coalesce backup buffer address
 - Rename queue_num to n_queues
 - Don't log error message in __i40e_get_coalesce

Changes since V3:
 - Based on David's lib bitmap.
 - ETHTOOL_PERQUEUE should be handled before the containing switch
 - Make the rollback code unconditional
 - some minor changes according to Ben's feedback

Changes since V2:
 - Add queue-specific settings for interrupt moderation in i40e

Changes since V1:
 - Checking the sub-command number to determine whether the command
   requires CAP_NET_ADMIN
 - Refine the struct ethtool_per_queue_op and improve the comments
 - Use bitmap functions to parse queue mask
 - Improve comments
 - Use bitmap functions to parse queue mask
 - Improve comments
 - Add rollback support
 - Correct the way to find the vector for specific queue.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements set_per_queue_coalesce for i40e driver.
Signed-off-by: NKan Liang <kan.liang@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements get_per_queue_coalesce for i40e driver.
Signed-off-by: NKan Liang <kan.liang@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: NKan Liang <kan.liang@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements sub command ETHTOOL_SCOALESCE for ioctl
ETHTOOL_PERQUEUE. It introduces an interface set_per_queue_coalesce to
set coalesce of each masked queue to device driver. The wanted coalesce
information are stored in "data" for each masked queue, which can copy
from userspace.
If it fails to set coalesce to device driver, the value which already
set to specific queue will be tried to rollback.
Signed-off-by: NKan Liang <kan.liang@intel.com>
Reviewed-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements sub command ETHTOOL_GCOALESCE for ioctl
ETHTOOL_PERQUEUE. It introduces an interface get_per_queue_coalesce to
get coalesce of each masked queue from device driver. Then the interrupt
coalescing parameters will be copied back to user space one by one.
Signed-off-by: NKan Liang <kan.liang@intel.com>
Reviewed-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a new ioctl ETHTOOL_PERQUEUE for per queue parameters setting.
The following patches will enable some SUB_COMMANDs for per queue
setting.
Signed-off-by: NKan Liang <kan.liang@intel.com>
Reviewed-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is mainly testing bitmap construction and conversion to/from u32[]
for now.

Tested:
  qemu i386, x86_64, ppc, ppc64 BE and LE, ARM.
Signed-off-by: NDavid Decotigny <decot@googlers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Aimed at transferring bitmaps to/from user-space in a 32/64-bit agnostic
way.

Tested:
  unit tests (next patch) on qemu i386, x86_64, ppc, ppc64 BE and LE,
  ARM.
Signed-off-by: NDavid Decotigny <decot@googlers.com>
Reviewed-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable skb_tx_timestamp in hyperv netvsc.
Signed-off-by: NSimon Xiao <sixiao@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ipv4,  when  the machine receives a ICMP_FRAG_NEEDED message,  the
connected UDP socket will get EMSGSIZE message on its next read from the
socket.
However, this is not the case for ipv6.
This fix modifies the udp err handler in Ipv6 for ICMP6_PKT_TOOBIG to
make it similar to ipv4 behavior. That is when the machine gets an
ICMP6_PKT_TOOBIG message, the connected UDP socket will get EMSGSIZE
message on its next read from the socket.
Signed-off-by: NWei Wang <weiwan@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Interrupts registered by RoCE driver are not unregistered when
msix interrupts are disabled during error recovery causing a
crash. Detach the adapter instance from RoCE driver when error
is detected to complete the cleanup. Attach the driver again after
the adapter is recovered from error.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As requested by Rob Herring on patch
https://patchwork.ozlabs.org/patch/580862/.

This is a new property that it's still in net-next and has never been
used in production, so we are not breaking anything with the
incompatible binding change.
Signed-off-by: NSergio Prado <sergio.prado@e-labworks.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
bridge: mdb: add support for extended attributes

This small set allows to extend the per mdb entry exported attributes,
before this set we had only a structure exported which couldn't be changed
because we would've broken user-space, after this we extend the attribute
that was used for the structure and add per-mdb entry attributes after the
struct has been added (see patch 02 for more details). Note that the reason
we can't simply add an attribute after MDBA_MDB_ENTRY_INFO is that current
users (e.g. iproute2) walk over the attribute list directly without
checking for the attribute type.
Patch 01 is a simple change to reduce one indentation level in order to
avoid over 80 char lines.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently mdb entries are exported directly as a structure inside
MDBA_MDB_ENTRY_INFO attribute, we can't really extend it without
breaking user-space. In order to export new mdb fields, I've converted
the MDBA_MDB_ENTRY_INFO into a nested attribute which starts like before
with struct br_mdb_entry (without header, as it's casted directly in
iproute2) and continues with MDBA_MDB_EATTR_ attributes. This way we
keep compatibility with older users and can export new data.
I've tested this with iproute2, both with and without support for the
added attribute and it works fine.
So basically we again have MDBA_MDB_ENTRY_INFO with struct br_mdb_entry
inside but it may contain also some additional MDBA_MDB_EATTR_ attributes
such as MDBA_MDB_EATTR_TIMER which can be parsed by user-space.

So the new structure is:
[MDBA_MDB] = {
     [MDBA_MDB_ENTRY] = {
         [MDBA_MDB_ENTRY_INFO]
         [MDBA_MDB_ENTRY_INFO] { <- Nested attribute
             struct br_mdb_entry <- nla_put_nohdr()
             [MDBA_MDB_ENTRY attributes] <- normal netlink attributes
         }
     }
}
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch the port check and skip if it's null, this allows us to reduce one
indentation level.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bpf_percpu_hash_update() expects rcu lock to be held and warns if it's not,
which pointed out a missing rcu read lock.

Fixes: 15a07b33 ("bpf: add lookup/update support for per-cpu hash and array maps")
Signed-off-by: NSasha Levin <sasha.levin@oracle.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2016-02-19

This series contains updates to i40e/i40evf only.

Alex Duyck splits up the descriptor count function from the function that
stops the ring to have access to the descriptor count used for the data
portion of the frame.  The rewrites the logic for how we determine if we
can transmit the frame or if it needs to be linearized.  Place the checksum
close to TSO since they have a lot in common and it can help to reduce the
decision tree for how to handle the frame as the first check in TSO is to
see if checksumming is offloaded.

Carolyn adds functions to blink leds on devices using 10GBaseT PHY since
MAC registers used in other designs do not work in this device configuration.
Fixes an issue where a previously removed message has returned.

Kevin increases the timeout when checking GLGEN_RSTAT_DEVSTATE bit since
linking with particular PHY types, the amount of time it takes for the
GLGEN_RSTAT_DEVSTATE to be set increases greatly.

Neerav changes the receive queues to not wait to be disabled before DCB
has been reconfigured, like transmit queues.

Anjali adds new register definitions for programming the parser, flow
director and RSS blocks in the hardware.

Shannon adds the new opcodes and structures used for asking the firmware
to update receive control registers that need extra care when being
accessed while under heavy traffic.  Integrates the new AdminQ functions
for safely accessing the receive control registers that may be affected
by heavy small packet traffic.

Mitch provides another colorful patch description on letting go of
the stale local VSI pointer when the VF resets.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump.

Change-ID: Ifa19aadaa892ad103f1b96fe2361fa690912c6a3
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If we reset a VF, its VSI goes away, and it gets a new one. So don't
hang on to the now-stale local VSI pointer. It just leads to suffering
and kernel panics.

Change-ID: Ia8823b4e85893e95e963acee284968022b29177a
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We need to suspend scheduling or any pending service task during driver
unload process, so that new task will not be scheduled. This patch sets
the suspend flag bit during reload which avoids service task execution.

Change-ID: I017c57b5d6656564556e3c5387da671369a572ac
Signed-off-by: NPandi Kumar Maharajan <pandi.maharajan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.

We can't use AdminQ calls in i40e_clear_hw() because the HW is being
initialized and the AdminQ is not alive.  We recently added an AQ
related replacement for reading PFLAN_QALLOC, and this patch puts
back the original register read.

Change-ID: Ib027168c954a5733299aa3a4ce5f8218c6bb5636
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.

Change-ID: Ibb00983e8dcba71f4b760222a609a5fcaa726f18
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the new opcodes and struct used for asking the firmware to update Rx
control registers that need extra care when being accessed while under
heavy traffic - e.g. sustained 64byte packets at line rate on all ports.
The firmware will take extra steps to be sure the register accesses
are successful.

The registers involved are:
	PFQF_CTL_0
	PFQF_HENA
	PFQF_FDALLOC
	PFQF_HREGION
	PFLAN_QALLOC
	VPQF_CTL
	VFQF_HENA
	VFQF_HREGION
	VSIQF_CTL
	VSILAN_QBASE
	VSILAN_QTABLE
	VSIQF_TCREGION
	PFQF_HKEY
	VFQF_HKEY
	PRTQF_CTL_0
	GLFCOE_RCTL
	GLFCOE_RSOF
	GLQF_CTL
	GLQF_SWAP
	GLQF_HASH_MSK
	GLQF_HASH_INSET
	GLQF_HSYM
	GLQF_FC_MSK
	GLQF_FC_INSET
	GLQF_FD_MSK
	PRTQF_FD_INSET
	PRTQF_FD_FLXINSET
	PRTQF_FD_MSK

Change-ID: I56c8144000da66ad99f68948d8a184b2ec2aeb3e
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Return from i40e_vsi_reinit_setup() if vsi param is NULL.
This makes this code consistent with all the other code that
checks for NULL before using one of the VSI pointers accessed
with an indexed variable. (Indexed VSI pointers are
intentionally set to NULL in i40e_vsi_clear() and
i40e_remove().

Change-ID: I3bc8b909c70fd2439334eeae994d151f61480985
Signed-off-by: NJohn Underwood <johnx.underwood@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds 7 new register definitions for programming the
parser, flow director and RSS blocks in the HW.

Change-ID: I31e76673125275f3c69a14c646361919d04dc987
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This fixes an issue where a previously removed message
has returned.  Changing the message type to dev_dbg
leaves the info, if desired, but takes it out of normal
everyday usage. Also changed call to only provide port
data when its valid and not when its not (delete case).

Change-ID: Ief6f33b915f6364c24fa8e5789c2fc3168b5e2ed
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just like Tx queues don't wait for Rx queues to be disabled before
DCB has been reconfigured.
Check the queues are disabled only after the DCB configuration has
been applied to the VSI(s) managed by the PF driver.

In case of any timeout issue a PF reset to recover.

Change-ID: Ic51e94c25baf9a5480cee983f35d15575a88642c
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When linking with particular PHY types (ex: copper PHY), the amount of
time it takes for the GLGEN_RSTAT_DEVSTATE to be set increases greatly,
which can lead to a timeout and failure to load the driver.

Change-ID: If02be0dfcd7c57fdde2d5c81cd63651260cd2029
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where the ethtool identify adapter
functionality did not work for some copper PHY's.  Without this
patch, the blink led functionality fails on some parts.  This
patch adds PHY write code to blink led's on parts where this
functionality is contained in the PHY rather than the MAC.

Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds functions to blink led on devices using
10GBaseT PHY since MAC registers used in other designs
do not work in this device configuration.

Change-ID: Id4b88c93c649fd2b88073a00b42867a77c761ca3
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On all of the other Intel drivers we place checksum close to TSO as they
have a significant amount in common and it can help to reduce the decision
tree for how to handle the frame as the first check in TSO is to see if
checksumming is offloaded, and if it is not we can skip _BOTH_ TSO and Tx
checksum offload based on a single check.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to rewrite the logic for how we determine if we can
transmit the frame or if it needs to be linearized.

The previous code for this function was using a mix of division and modulus
division as a part of computing if we need to take the slow path.  Instead
I have replaced this by simply working with a sliding window which will
tell us if the frame would be capable of causing a single packet to span
several descriptors.

The logic for the scan is fairly simple.  If any given group of 6 fragments
is less than gso_size - 1 then it is possible for us to have one byte
coming out of the first fragment, 6 fragments, and one or more bytes coming
out of the last fragment.  This gives us a total of 8 fragments
which exceeds what we can allow so we send such frames to be linearized.

Arguably the use of modulus might be more exact as the approach I propose
may generate some false positives.  However the likelihood of us taking much
of a hit for those false positives is fairly low, and I would rather not
add more overhead in the case where we are receiving a frame composed of 4K
pages.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In an upcoming patch I would like to have access to the descriptor count
used for the data portion of the frame.  For this reason I am splitting up
the descriptor count function from the function that stops the ring.

Also in order to try and reduce unnecessary duplication of code I am moving
the slow-path portions of the code out of being inline calls so that we can
just jump to them and process them instead of having to build them into
each function that calls them.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2016-02-18

This series contains updates to i40e and i40evf only.

Alex Duyck provides all the patches in the series to update and fix the
drivers.  Fixed the driver to drop the outer checksum offload on UDP
tunnels, since the issue is that the upper levels of the stack never
requested such an offload and it results in possible errors.  Updates the
TSO function to just use u64 values, so we do not have to end up casting
u32 values.  In the TSO path, factored out the L4 header offsets allowing
us to ignore the L4 header offsets when dealing with the L3 checksum and
length update.  Consolidates all of the spots where we were updating
either the TCP or IP checksums in the TSO and checksum path into the TSO
function.  Fixed two issues by adding support for IPv4 encapsulated in
IPv6, first issue was the fact that iphdr(skb)->protocol was being used to
test for the outer transport protocol which breaks IPv6 support.  The second
was that we cleared the flag for v4 going to v6, but we did not take care
of txflags going the other way.  Added support for IPv6 extension headers
in setting up the Tx checksum.  Added exception handling to the Tx
checksum path so that we can handle cases of TSO where the frame is bad,
or Tx checksum where we did not recognize a protocol.  Fixed a number of
issues to make certain that we are using the correct protocols when
parsing both the inner and outer headers of a frame that is mixed between
IPv4 and IPv6 for inner and outer.  Updated the feature flags to reflect
the newly enabled/added features.

Sorry, no witty patch descriptions this time around, probably should
let Mitch help in writing patch descriptions for Alex. :-)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e5d3a51c ("bnx2x: extend DCBx support") was missing HSI
changes for big-endian machine, breaking compilation on such
platforms.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the code for determining the L4 protocol and L3 header
length so that when IPv6 extension headers are being used we can determine
the offset and type of the L4 protocol.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent changes should have enabled support for IPv6 based tunnels and
support for TSO with outer UDP checksums.  As such we can update the
feature flags to reflect that.

In addition we can clean-up the flags that aren't needed such as SCTP and
RXCSUM since having the bits there doesn't add any value.

I also found one spot where we were setting the same flag twice.  It looks
like it was probably a git merge error that resulted in the line being
duplicated.  As such I have dropped it in this patch.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>