This patch just implements the basic enable and disable
functions of DC5 state which is needed for both SKL and BXT.

Its important to load respective CSR program before calling
enable, which anyways will happen as CSR program is executed
during boot.

DC5 is a power saving state where hardware dynamically disables
power well 1 and the CDCLK PLL and saves the associated registers.

DC5 can be entered when software allows it, power well 2 is
disabled, and hardware detects that all pipes are disabled
or pipe A is enabled with PSR active.

Its better to configure display engine to have power well 2 disabled before
getting into DC5 enable function. Hence rpm framework will have to
ensure to check status of power well 2 before calling gen9_enable_dc5.

Rather dc5 entry criteria should be decided based on power well 2 status.
If disabled, then call gen9_enable_dc5.

v2: Replace HAS_ with IS_ check as per Daniel's review comments

v3: Cleared the bits dc5/dc6 enable of DC_STATE_EN register
before setting them as per Satheesh's review comments.

v4: call POSTING_READ for every write to a register to ensure that
its written immediately.

v5: Modified as per review comments from Imre.
- Squashed register definitions into this patch.
- Finetuned comments and functions.

v6:
Avoid redundant writes in gen9_set_dc_state_debugmask_memory_up function.

v7:
- Rebase to latest.
- Move all runtime PM functions defined in intel_display.c to
  intel_runtime_pm.c.

v8: Rebased to drm-intel-nightly. (Animesh)

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add triggers as per expectations mentioned in gen9_enable_dc5
and gen9_disable_dc5 patch.

Also call POSTING_READ for every write to a register to ensure that
its written immediately.

v1: Remove POSTING_READ calls as they've already been added in previous patches.

v2: Rebase to move all runtime pm specific changes to intel_runtime_pm.c file.

Modified as per review comments from Imre:
1] Change variable name 'dc5_allowed' to 'dc5_enabled' to correspond to relevant
   functions.
2] Move the check dc5_enabled in skl_set_power_well() to disable DC5 into
   gen9_disable_DC5 which is a more appropriate place.
3] Convert checks for 'pm.dc5_enabled' and 'pm.suspended' in skl_set_power_well()
   to warnings. However, removing them for now as they'll be included in a future patch
   asserting DC-state entry/exit criteria.
4] Enable DC5, only when CSR firmware is verified to be loaded. Create new structure
   to track 'enabled' and 'deferred' status of DC5.
5] Ensure runtime PM reference is obtained, if CSR is not loaded, to avoid entering
   runtime-suspend and release it when it's loaded.
6] Protect necessary CSR-related code with locks.
7] Move CSR-loading call to runtime PM initialization, as power domains needed to be
   accessed during deferred DC5-enabling, are not initialized earlier.

v3: Rebase to latest.

Modified as per review comments from Imre:
1] Use blocking wait for CSR-loading to finish to enable DC5  for simplicity, instead of
   deferring enabling DC5 until CSR is loaded.
2] Obtain runtime PM reference during CSR-loading initialization itself as deferred DC5-
   enabling is removed and release it at the end of CSR-loading functionality.
3] Revert calling CSR-loading functionality to the beginning of i915 driver-load
   functionality to avoid any delay in loading.
4] Define another variable to track whether CSR-loading failed and use it to avoid enabling
   DC5 if it's true.
5] Define CSR-load-status accessor functions for use later.

v4:
1] Disable DC5 before enabling PG2 instead of after it.
2] DC5 was being mistaken enabled even when CSR-loading timed-out. Fix that.
3] Enable DC5-related functionality using a macro.
4] Remove dc5_enabled tracking variable and its use as it's not needed now.

v5:
1] Mark CSR failed to load where necessary in finish_csr_load function.
2] Use mutex-protected accessor function to check if CSR loaded instead of directly
   accessing the variable.
3] Prefix csr_load_status_get/set function names with intel_.

v6: rebase to latest.
v7: Rebase on top of nightly (Damien)
v8: Squashed the patch from Imre - added csr helper pointers to simplify the code. (Imre)
v9: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v10: Added a enum for different csr states, suggested by Imre. (Animesh)

v11: Based on review comments from Imre, Damien and Daniel following changes done
- enum name chnaged to csr_state (singular form).
- FW_UNINITIALIZED used as zeroth element in enum csr_state.
- Prototype changed for helper function(set/get csr status), using enum csr_state instead of bool.

v12: Based on review comment from Imre, introduced bool fw_loaded local to finish_csr_load() which helps
calling once to set the csr status. The same flag used to fail RPM if find any issue during
firmware loading.

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Display Context Save and Restore support is needed for
various SKL Display C states like DC5, DC6.

This implementation is added based on first version of DMC CSR program
that we received from h/w team.

Here we are using request_firmware based design.
Finally this firmware should end up in linux-firmware tree.

For SKL platform its mandatory to ensure that we load this
csr program before enabling DC states like DC5/DC6.

As CSR program gets reset on various conditions, we should ensure
to load it during boot and in future change to be added to load
this system resume sequence too.

v1: Initial relese as RFC patch

v2: Design change as per Daniel, Damien and Shobit's review comments
request firmware method followed.

v3: Some optimization and functional changes.
Pulled register defines into drivers/gpu/drm/i915/i915_reg.h
Used kmemdup to allocate and duplicate firmware content.
Ensured to free allocated buffer.

v4: Modified as per review comments from Satheesh and Daniel
Removed temporary buffer.
Optimized number of writes by replacing I915_WRITE with I915_WRITE64.

v5:
Modified as per review comemnts from Damien.
- Changed name for functions and firmware.
- Introduced HAS_CSR.
- Reverted back previous change and used csr_buf with u8 size.
- Using cpu_to_be64 for endianness change.

Modified as per review comments from Imre.
- Modified registers and macro names to be a bit closer to bspec terminology
and the existing register naming in the driver.
- Early return for non SKL platforms in intel_load_csr_program function.
- Added locking around CSR program load function as it may be called
concurrently during system/runtime resume.
- Releasing the fw before loading the program for consistency
- Handled error path during f/w load.

v6: Modified as per review comments from Imre.
- Corrected out_freecsr sequence.

v7: Modified as per review comments from Imre.
Fail loading fw if fw->size%8!=0.

v8: Rebase to latest.

v9: Rebase on top of -nightly (Damien)

v10: Enabled support for dmc firmware ver 1.0.
According to ver 1.0 in a single binary package all the firmware's that are
required for different stepping's of the product will be stored. The package
contains the css header, followed by the package header and the actual dmc
firmwares. Package header contains the firmware/stepping mapping table and
the corresponding firmware offsets to the individual binaries, within the
package. Each individual program binary contains the header and the payload
sections whose size is specified in the header section. This changes are done
to extract the specific firmaware from the package. (Animesh)

v11: Modified as per review comemnts from Imre.
- Added code comment from bpec for header structure elements.
- Added __packed to avoid structure padding.
- Added helper functions for stepping and substepping info.
- Added code comment for CSR_MAX_FW_SIZE.
- Disabled BXT firmware loading, will be enabled with dmc 1.0 support.
- Changed skl_stepping_info based on bspec, earlier used from config DB.
- Removed duplicate call of cpu_to_be* from intel_csr_load_program function.
- Used cpu_to_be32 instead of cpu_to_be64 as firmware binary in dword aligned.
- Added sanity check for header length.
- Added sanity check for mmio address got from firmware binary.
- kmalloc done separately for dmc header and dmc firmware. (Animesh)

v12: Modified as per review comemnts from Imre.
- Corrected the typo error in skl stepping info structure.
- Added out-of-bound access for skl_stepping_info.
- Sanity check for mmio address modified.
- Sanity check added for stepping and substeppig.
- Modified the intel_dmc_info structure, cache only the required header info. (Animesh)

v13: clarify firmware load error message.
The reason for a firmware loading failure can be obscure if the driver
is built-in. Provide an explanation to the user about the likely reason for
the failure and how to resolve it. (Imre)

v14: Suggested by Jani.
- fix s/I915/CONFIG_DRM_I915/ typo
- add fw_path to the firmware object instead of using a static ptr (Jani)

v15:
1) Changed the firmware name as dmc_gen9.bin, everytime for a new firmware version a symbolic link
with same name will help not to build kernel again.
2) Changes done as per review comments from Imre.
- Error check removed for intel_csr_ucode_init.
- Moved csr-specific data structure to intel_csr.h and optimization done on structure definition.
- fw->data used directly for parsing the header info & memory allocation
only done separately for payload. (Animesh)

v16:
- No need for out_regs label in i915_driver_load(), so removed it.
- Changed the firmware name as skl_dmc_ver1.bin, followed naming convention <platform>_dmc_<api-version>.bin (Animesh)

Issue: VIZ-2569
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

i915_needs_cmd_parser already checks that for us.
Suggested-by: NMika Kuoppala <mika.kuoppala@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Signed-off-by: NNick Hoath <nicholas.hoath@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables skylake sprite plane display scaling using shared
scalers atomic desgin.

v2:
-use single copy of scaler limits (Matt)

v3:
-detaching scalers moved to crtc commit path (Matt)

v4:
-changes to align with updated scaler structures (Matt, me)
-keep sprite src rect in 16.16 format (Matt, Daniel)

v5:
-rebased on top of 90/270 rotation changes (me)
-Refactored skl_update_plane to reduce its size (Daniel)
 It is a step towards having a single function covering all planes.
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Testcase: igt/kms_plane_scaling
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables skylake primary plane scaling using shared
scalers atomic desgin.

v2:
-use single copy of scaler limits (Matt)

v3:
-move detach_scalers to crtc commit path (Matt)
-use values in plane_state->src as regular integers (me)

v4:
-changes to align with updated scaler structures (Matt, me)
-keep plane src rect in 16.16 format (Matt, Daniel)

v5:
-Rebased on top of 90/270 rotation changes (me)
-Fixed an issue introduced by 90/270 changes where plane programming
 is using drm_plane->state rect instead of intel_plane->state rect.
 This change also required for scaling to work properly. (me)
-With 90/270, updated limits to cover both portrait and landscape usages (me)
-Refactored skylake_update_primary_plane to reduce its size (Daniel)
 Added helper functions for refactoring are comprehended enough to be
 used for skylake_update_plane (for sprite) too. One stop towards
 having single function for all planes.

v6:
-Added fixme note when checking plane_state->src width in update_plane (Daniel)
-Release lock when failing to colorkey request with active scaler (Daniel)
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: matthew.d.roper@intel.com
Reviewed-by: sonika.jindal@intel.com (v5)
Testcase: igt/kms_plane_scaling
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Completely different approach:  Instead of encoding each and every
framebuffer update as spice operation simply update the shadow
framebuffer and maintain a dirty rectangle.  Also schedule a worker
to push an update for the dirty rectangle as spice operation.  Usually
a bunch of dirty rectangle updates are collected before the worker
actually runs.

What changes:  Updates get batched now.  Instead of sending tons of
small updates a few large ones are sent.  When the same region is
updated multiple times within a short timeframe (scrolling multiple
lines for example) we send a single update only.  Spice server has an
easier job now:  The dependency tree for display operations which spice
server maintains for lazy rendering is alot smaller now.  Spice server's
image compression probably works better too with the larger image blits.

Net effect:  framebuffer console @ qxldrmfb is an order of magnitude
faster now.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In drm_master_destroy() we _free_ the master object. There is no reason to
hold any locks while dropping its static members, nor do we have to reset
it to 0.

Furthermore, kfree() already does NULL checks, so call it directly on
master->unique and drop the redundant reset-code.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The magic auth tokens we have are a simple map from cyclic IDs to drm_file
objects. Remove all the old bulk of code and replace it with a simple,
direct IDR.

The previous behavior is kept. Especially calling authmagic multiple times
on the same magic results in EINVAL except on the first call. The only
difference in behavior is that we never allocate IDs multiple times as
long as a client has its FD open.

v2:
 - Fix return code of GetMagic()
 - Use non-cyclic IDR allocator
 - fix off-by-one in "magic > INT_MAX" sanity check

v3:
 - drop redundant "magic > INT_MAX" check
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This list is write-only. It's never used for read-access, so no reason to
keep it around. Drop it!
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Need to free just allocated ctx allocation if we cannot
get our config mutex.

This one has been flagged by kbuild bot all the way back in August,
but somehow nobody picked it up:
https://lists.01.org/pipermail/kbuild/2014-August/001691.html

In addition there is another failure path that leaks the same
ctx reference that is fixed.

Found with smatch.
Signed-off-by: NOleg Drokin <green@linuxhacker.ru>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I've fumbled this in

commit f02ad907
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Jan 22 16:36:23 2015 +0100

    drm/atomic-helpers: Recover full cursor plane behaviour

and accidentally put the assignment for legacy_cursor_upate after the
atomic commit, where it is pretty useless.
Reported-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

This breaks under the vblank timestamp cleanup patch
by Daniel Vetter. Also it is pointless to return anything
but zero (or any other constant) if the function doesn't
actually query a hw vblank counter. The bogus return of
the current drm vblank counter via direct readout or via
drm_vblank_count() is found in many of the new kms drivers,
but it does exactly nothing different from returning any
arbitrary constant - it's a no operation.

Let's simply return 0 - Easy and fast.
Signed-off-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since commit 844b03f2 we make
sure that after vblank irq off, we return the last valid
(vblank count, vblank timestamp) pair to clients, e.g., during
modesets, which is good.

An overlooked side effect of that commit for kms drivers without
support for precise vblank timestamping is that at vblank irq
enable, when we update the vblank counter from the hw counter, we
can't update the corresponding vblank timestamp, so now we have a
totally mismatched timestamp for the new count to confuse clients.

Restore old client visible behaviour from before Linux 3.18, but
zero out the timestamp at vblank counter update (instead of disable
as in original implementation) if we can't generate a meaningful
timestamp immediately for the new vblank counter. This will fix
this regression, so callers know they need to retry again later
if they need a valid timestamp, but at the same time preserves
the improvements made in the commit mentioned above.

v2: Rebased on top of Daniel Vetter's fixup and documentation
    patch for timestamp updates. Drop request for stable kernel
    backport as this would be more difficult, unless the original
    patch would get applied to stable kernels.
Signed-off-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For a kms driver to support immediate disable of vblank
irq's reliably without introducing off by one errors or
other mayhem for clients, it must not only support a
hardware vblank counter query, but also high precision
vblank timestamping, so vblank count and timestamp can be
instantaneously reinitialzed to valid values. Additionally
the exposed hardware counter must behave as if it is
incrementing at leading edge of vblank to avoid off by
one errors during reinitialization of the counter while
the display happens to be inside or close to vblank.

Check during drm_vblank_init that a driver which claims to
be capable of vblank_disable_immediate at least supports
high precision timestamping and prevent use of instant
disable if that isn't present as a minimum requirement.

v2: Changed from DRM_ERROR to DRM_INFO and made message
    more clear, as suggested by Michel Dänzer.
Signed-off-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was a bit too much cargo-culted, so lets make it solid:
- vblank->count doesn't need to be an atomic, writes are always done
  under the protection of dev->vblank_time_lock. Switch to an unsigned
  long instead and update comments. Note that atomic_read is just a
  normal read of a volatile variable, so no need to audit all the
  read-side access specifically.

- The barriers for the vblank counter seqlock weren't complete: The
  read-side was missing the first barrier between the counter read and
  the timestamp read, it only had a barrier between the ts and the
  counter read. We need both.

- Barriers weren't properly documented. Since barriers only work if
  you have them on boths sides of the transaction it's prudent to
  reference where the other side is. To avoid duplicating the
  write-side comment 3 times extract a little store_vblank() helper.
  In that helper also assert that we do indeed hold
  dev->vblank_time_lock, since in some cases the lock is acquired a
  few functions up in the callchain.

Spotted while reviewing a patch from Chris Wilson to add a fastpath to
the vblank_wait ioctl.

v2: Add comment to better explain how store_vblank works, suggested by
Chris.

v3: Peter noticed that as-is the 2nd smp_wmb is redundant with the
implicit barrier in the spin_unlock. But that can only be proven by
auditing all callers and my point in extracting this little helper was
to localize all the locking into just one place. Hence I think that
additional optimization is too risky.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-and-tested-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed.  Otherwise block layer ends up confused and we
trip on

    rbd_assert(more ^ (which == img_request->obj_request_count));

in rbd_img_obj_callback() due to more being true no matter what.  We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.

A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.

Cc: Alex Elder <elder@linaro.org>
Cc: stable@vger.kernel.org # 3.10+
Reported-by: NShawn Edwards <lesser.evil@gmail.com>
Reviewed-by: NSage Weil <sage@redhat.com>
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

RGMII-ID uses an internal delay within the transmitter or receiver. This
feature is phy specific. The rest of the communication is normal RGMII.

So the fec driver has to check for all RGMII modes, not only
'PHY_INTERFACE_MODE_RGMII'.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When system is out of memory, refilling of RX buffers fails while
the driver continue to pass the received packets to the kernel stack.
At some point, when all RX buffers deplete, driver may fall into a
sleep, and not recover when memory for new RX buffers is once again
availible. This is because hardware does not have valid descriptors,
so no interrupt will be generated for the driver to return to work
in napi context. Fix it by schedule the napi poll function from
stats_task delayed workqueue, as long as the allocations fail.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While testing this driver with DEBUG_LOCKDEP and DEBUG_SPINLOCK
enabled did not produce any traces, it would be more prudent in the
case of tx_clean_lock to use spin_[un]lock_bh, since this lock is
manipulated in both the process and softirq contexts.

This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: NTony Camuso <tcamuso@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Addresses the following kernel logs seen during boot:

Kernel unaligned access at TPC[100ee150] mlx4_QUERY_HCA+0x80/0x248 [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Kernel unaligned access at TPC[100f071c] mlx4_QUERY_ADAPTER+0x100/0x12c [mlx4_core]
Signed-off-by: NDavid Ahern <david.ahern@oracle.com>
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBenjamin Poirier <bpoirier@suse.de>
Fixes: 9e311e77 ("net/mlx4_en: Use affinity hint")
Acked-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 02233342 ("dm: optimize dm_mq_queue_rq to _not_ use kthread if
using pure blk-mq") mistakenly removed free_rq_clone()'s clone->q check
before testing clone->q->mq_ops.  It was an oversight to discontinue
that check for 1 of the 2 use-cases for free_rq_clone():
1) free_rq_clone() called when an unmapped original request is requeued
2) free_rq_clone() called in the request-based IO completion path

The clone->q check made sense for case #1 but not for #2.  However, we
cannot just reinstate the check as it'd mask a serious bug in the IO
completion case #2 -- no in-flight request should have an uninitialized
request_queue (basic block layer refcounting _should_ ensure this).

The NULL pointer seen for case #1 is detailed here:
https://www.redhat.com/archives/dm-devel/2015-April/msg00160.html

Fix this free_rq_clone() NULL pointer by simply checking if the
mapped_device's type is DM_TYPE_MQ_REQUEST_BASED (clone's queue is
blk-mq) rather than checking clone->q->mq_ops.  This avoids the need to
dereference clone->q, but a WARN_ON_ONCE is added to let us know if an
uninitialized clone request is being completed.
Reported-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Commit bfebd1cd ("dm: add full blk-mq support to request-based DM")
didn't properly account for the need to short-circuit re-initializing
DM's blk-mq request_queue if it was already initialized.

Otherwise, reloading a blk-mq request-based DM table (either manually
or via multipathd) resulted in errors, see:
 https://www.redhat.com/archives/dm-devel/2015-April/msg00132.html

Fix is to only initialize the request_queue on the initial table load
(when the mapped_device type is assigned).

This is better than having dm_init_request_based_blk_mq_queue() return
early if the queue was already initialized because it elevates the
constraint to a more meaningful location in DM core.  As such the
pre-existing early return in dm_init_request_based_queue() can now be
removed.

Fixes: bfebd1cd ("dm: add full blk-mq support to request-based DM")
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

When we have bound vma into an address space, the layout
of page table structures is immutable. So we can be absolutely
certain that if vma is already bound, there is no need to
(re)allocate a virtual address range for it.

v2: - add sanity checks and remove superfluous GLOBAL_BIND set
    - we might do update for an unbound vma (Chris)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90224
Testcase: igt/gem_exec_big #bdw
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

With the binding regression from the original full ppgtt patches
fixed we can throw the switch. Yay!

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90190Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
[Jani: tweaked commit title per Chris' suggestion]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

At the moment intel_prepare_ddi buffer will iterate through both MST and
CRT encoders, which is incorrect. Neither of these encoder types have an
embedding intel_digital_port object, so for these encoder types we will
use random data when dereferencing the corresponding
intel_digital_port->port field.

Introduced in
commit b403745c
Author: Damien Lespiau <damien.lespiau@intel.com>
Date:   Mon Aug 4 22:01:33 2014 +0100

    drm/i915: Iterate through the initialized DDIs to prepare their buffers

v2:
- fix getting at the port for MST encoders too
- make sure that intel_prepare_ddi_buffers() gets called for port E too
  (Paulo)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90067Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

In the next patch we'll need to get at both the encoder's intel_digital_port
object - which maybe NULL for a CRT - and it's port, so factor out this
functionality.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Add port check for ibx similar to vlv in

commit 535afa2e
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Wed Apr 15 16:52:29 2015 -0700

    drm/i915/vlv: check port in infoframe_enabled v2
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Due to missing shifting, the vlv infoframe port check only works for
port A. Fix it. Broken since introduction in

commit 535afa2e
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Wed Apr 15 16:52:29 2015 -0700

    drm/i915/vlv: check port in infoframe_enabled v2

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90059Tested-by: Nxubin <bin.a.xu@intel.com>
Tested-by: NYe Tian <yex.tian@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Commit 6559a7e8 ("cxgb4: Cleanup macros so they follow the same
style and look consistent") introduced a regression where reading MC1
memory in adapters where MC0 isn't present or MC0 size is not equal to MC1
size caused the adapter to crash due to incorrect computation of memoffset.
Fix is to read the size of MC0 instead of MC1 for offset calculation
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a kdump environment interfaces might be re-loaded without a proper
unload sequence in the previous running kernel.
bnx2x management FW and driver maintains a `pulse' that notifies the FW
that the driver is still up and running.

Driver load on the kdump kernel should be performed only after the pulse
has been out-of-sync long enough for the management FW to identify that
the driver has crashed, on which point it will perform some necessary
cleanup of the HW.

In today's distros kdump loading is quite fast, sometimes too fast for our
FW to get out-of-sync. This patch delays the bnx2x's probe during kdump
to allow a proper re-load on the kdump kernel.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a Kernel Panic in bonding driver debugfs file: rlb_hash_table.

$> modprobe bonding mode=6
$> cat /sys/kernel/debug/bonding/bond0/rlb_hash_table

This will crash the kernel. The struct alb_bond_info is initialized only when
the bonding interface is initialized (ip link set bond0 up) and not at the time
it is allocated. If we try to read the table before that, it'll result in a
kernel panic.

The patch applies against both net and net-next
Signed-off-by: NVishwanath Pai <vpai@akamai.com>
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under heavy Rx load, observed that the Hw is updating the USED bit
and it is not updating the received frame status to the BD control
field. This could be lack of resources for processing the BDs at high
data rates. Driver drops the frame associated with this BD but not
clearing the USED bit. So, this is causing hang condition as Hw
expects USED bit to be cleared for this BD.
Signed-off-by: NPunnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b08cc791 eliminated memory
allocation in the packet send path:

    "hv_netvsc: Eliminate memory allocation in the packet send path

    The network protocol used to communicate with the host is the remote ndis (rndis)
    protocol. We need to decorate each outgoing packet with a rndis header and
    additional rndis state (rndis per-packet state). To manage this state, we
    currently allocate memory in the transmit path. Eliminate this allocation by
    requesting additional head room in the skb."

This commit introduced a bug since it did not account for the case if the skb
was cloned. Fix this bug.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Tested-by: NDexuan Cui <decui@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Altera TSE MAC rx DMA transfer starts with the 2 additional bytes for IP
payload alignment. This patch fixes tse_rx() function loop which reads DMA
rx status and extracts packet length from it. Status signalises a whole DMA
transfer length, which is 2 bytes longer than the packet itself.
Signed-off-by: NVlastimil Setka <setka@vsis.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, the number of tx queues is limited by the number of online cpus
in mlx4_en_get_profile(). However, this limit no longer holds after the
ethtool .set_channels method has been called. In that situation, the driver
may access invalid bits of certain cpumask variables when queue_index >=
nr_cpu_ids.
Signed-off-by: NBenjamin Poirier <bpoirier@suse.de>
Acked-by: NIdo Shamay <idos@mellanox.com>
Fixes: d03a68f8 ("net/mlx4_en: Configure the XPS queue mapping on driver load")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.

Libraries like libnl will wait forever for NLMSG_DONE.

Fixes: e5a55a89 ("net: create generic bridge ops")
Fixes: 815cccbf ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the 0x0x prefix in an integer constant.

In this case, while at it, also fix a typo (s/unitcast/unicast/).
Signed-off-by: NAntonio Ospite <ao2@ao2.it>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>