In nommu mode, the exception vector location depends on the platforms.
Some of the implementations may have some special exception control
forwarding method in their ROM/flash and for some of them has its own
re-mapping mechanism by the h/w.

This patch introduces a special configuration CONFIG_CPU_HIGH_VECTOR which
turns on the CR_V bit in nommu mode. The CR_V bit is turned off by default.
This feature depends on CP15 and does not supported by ARM740.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There is no FSR/FAR register on no-CP15 or MPU cores. This patch adds a
dummy abort handler which returns zero for the base restored Data Abort
model !CPU_CP15_MMU cores. The abort-lv4t.S is still used with the fix-up
for the base updated Data Abort model cores.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Don't offer non-MMU based CPUs for selection when CONFIG_MMU is
set.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM946E-S core support which has typically 8KB I&D cache.
It has a MPU and supports ARMv5TE instruction set.

Because the ARM946E-S core can be synthesizable with various cache size,
CONFIG_CPU_DCACHE_SIZE is defined for vendor specific configurations.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM940T core support which has 4KB D-cache, 4KB I-cache
and a MPU.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM9TDMI core support which has no cache and no CP15
register(no memory control unit).
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM740T core support which has a MPU and 4KB or 8KB cache.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM7TDMI core support which has no cache and no CP15
register(no memory control unit).
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

All the current CP15 access codes in ARM arch can be categorized and
conditioned by the defines as follows:

     Related operation	Safe condition
  a. any CP15 access	!CPU_CP15
  b. alignment trap	CPU_CP15_MMU
  c. D-cache(C-bit)	CPU_CP15
  d. I-cache		CPU_CP15 && !( CPU_ARM610 || CPU_ARM710 ||
				CPU_ARM720 || CPU_ARM740 ||
				CPU_XSCALE || CPU_XSC3 )
  e. alternate vector	CPU_CP15 && !CPU_ARM740
  f. TTB		CPU_CP15_MMU
  g. Domain		CPU_CP15_MMU
  h. FSR/FAR		CPU_CP15_MMU

For example, alternate vector is supported if and only if
"CPU_CP15 && !CPU_ARM740" is satisfied.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

By merging of uClinux/ARM, we need to treat various CPU cores which have
MMU, MPU or even none for memory management. The memory management
coprocessors are controlled by CP15 register set and the ARM core family
can be categorized by 5 groups by the register ;
  G-a. CP15 is MMU : 610, 710, 720, 920, 922, 925, 926, 1020, 1020e, 1022,
		v6 and the derivations sa1100, sa110, xscale, xsc3.
  G-b. CP15 is MPU : 740, 940, 946, 996, 1156.
  G-c. CP15 is MPU or MMU : 1026 (selectable by schematic design)
  G-d. CP15 is exist, but nothing for memory managemnt : 966, 968.
  G-e. no-CP15 : 7tdmi, 9tdmi, 9e, 9ej

This patch defines CPU_CP15, CPU_CP15_MMU and CPU_CP15_MPU. Thus the
family can be defined as :
  - CPU_CP15 only : G-d
  - CPU_CP15_MMU(implies CPU_CP15) : G-a, G-c(selectable)
  - CPU_CP15_MPU(implies CPU_CP15) : G-b, G-c(selectable)
  - !CPU_CP15 : G-e
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

A simple patch to support module in nommu mode.
The vmalloc is used instead of __vmalloc_area which depends on CONFIG_MMU.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since do_bad_area() always takes the currently active task and
(supposed to) take the currently active MM, there's no point passing
them to this function.  Instead, obtain references to them inside
do_bad_area().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add an empty setup_mm_for_reboot() function for nommu machines.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

mm-armv.c now only contains the pgd allocation/freeing code, so
rename it to have a more sensible filename.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If we're going to have mmu.c for code which is specific to the MMU
machines, we might as well move the other MMU initialisation
specific code from mm-armv.c into this new file.  This also allows
us to make some functions static.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the MMU specific code from init.c into mmu.c, and add nommu
fixups to nommu.c
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

nommu does not require the page table manipulation code in the
bootmem initialisation paths.  Move this into separate inline
functions.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ARM Versatile board PCI config space read routines are broken for byte
accesses.  The access uses a byte read, so masking the bottom two bits of the
address is wrong.

I guess this is a cut/paste error from the the halfword code which uses
aligned word access+shift+mask.
Signed-off-by: NPaul Brook <paul@codesourcery.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ARM XIP_KERNEL map created in devicemaps_init() is wrong.
The map.pfn is rounded down to an even 1MiB section boundary
which results in va/pa translations errors when XIP_PHYS_ADDR
starts on an odd 1MiB boundary and this causes the kernel to
hang.  This patch fixes ARM XIP_KERNEL translation errors for
the odd 1MiB XIP_PHYS_ADDR boundary case.
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add S3C2412 power management code, and move the
core register saving in from s3c2412.c
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the AML M5900 series to the list of supported machines in the
arch/arm/mach-s3c2410 directory. This ensures the core peripherals
are registered, and the timer source is configured. if selected in
the kernel config the framebuffer registers and mtd partition
information are set.  This version of the patch has corrected
formatting and removed the legacy procfs directory entry.
Signed-off-by: NDavid Anders <danders@amltd.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Adds support for CONFIG_DEBUG_ICEDCC for ARM11.
Tested on ARM1136 (OMAP2420).
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

- Document the meaning for OP_SCALAR, OP_SD and add OP_DD.
- Formatting cleanups
- Remove now redundant code for making compare instructions
  operate on scalar values.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

VECITR in Floating-Point Exception register indicates the number of
remaining short vector iterations after a potential exception was
detected.

In case of exception caused by scalar instructions, VECITR is NOT updated.
Therefore emulation for VFP must ignore VECITR field
and treat "veclen" as zero when recognizing scalar instructing.
Signed-off-by: NGen Fukatsu <fukatsu.gen@jp.panasonic.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The documentation for the ZBOOT_ROM_BSS config option describes it as
"The base address of 64KiB of read/write memory in the target for the
ROM-able zImage..." In actuality, it requires more than 100 KiB of
space in addition to enough space to hold the decompressed kernel.
This patch fixes the description in the Kconfig file.
Signed-off-by: NDan Fandrich <dfandrich@intrinsyc.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix thinko in the flush_ptrace_access() "if (expr)" for the ARM
VIPT non-aliasing cache case.  We only need to flush cache when
VM_EXEC is set in vma->vm_flags but "if (expr) always evaluates
to true on UP systems for the ARM VIPT non-aliasing cache case.
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the IO-Data GLAN Tank, from Martin Michlmayr.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the Thecus n2100 (80219-based.)
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

New s3c2410_defconfig, updated 2.6.18
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove the redundant Modification lines from
the top of the files in arch/arm/mach-s3c2410
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The S3C2412 LCD controller is different enough
to warrant renaming the platform device.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add new code for the S3C2412
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add new machine VSTMS
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NThomas Gleixner <tglx@linuxtronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove the old per-board defconfigs.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add one defconfig for all iop32x boards and one defconfig for all
iop33x boards.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since the iop32x code isn't iop321-specific, and the iop33x code isn't
iop331-specfic, do a s/iop321/iop32x/ and s/iop331/iop33x/, and tidy up
the code to conform to the coding style guidelines somewhat better.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Revamp the iop3xx board support: move the support code for each iop
board type into its own file, start using platform serial and platform
physmap flash devices, switch to a per-board time tick rate, and get
rid of the ARCH_EP80219 and STEPD config options by doing the relevant
checks at run time.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Squeeze three instructions out of the iop32x irq demuxer, and nine
out of the iop33x irq demuxer by using the hardware vector generator.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The iop33x loadsp hunk in arch/arm/boot/compressed/head.S serves
no purpose -- remove it.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>