No functional changes.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UARTs which do not trigger THRE interrupt if the fifo is already
empty when the interrupt is enabled need tx primed manually. These
UARTs are identified by the UART_BUG_TXEN flag to enable the
required workaround.

However, the current workaround is broken; if the fifo is already
empty but the shifter is still transmitting, then serial8250_tx_chars()
will not be called but no further THRE interrupt will occur, and
tx will stall. The appropriate check is for fifo empty (THRE), not
transmitter empty (TEMT).
Signed-off-by: NDick Hollenbeck <dick@softplc.com>
[pjh: rewrote commit log]
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/8250/8250_core.c:2503:6: sparse: symbol 'serial8250_set_divisor' was not declared. Should it be static?
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The port shadow registers, ->fcr and ->mcr, must be protected from
concurrent updates. Relocate the shadow register updates in
serial8250_do_set_termios() to the port lock critical section.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When using no_console_suspend, the serial console may be powered off
anyway during system sleep. Upon resume, the port may be in its default
power-on state, but is expected to continue console i/o before the device
has received its pm callback. The resultant garbage i/o can cause all
kinds of havoc on the remote end.

Use the scratch register as a canary to discover if the console
has been powered-off. Write a non-zero value to the scratch register
at port suspend and reprogram the port before any console i/o if the
scratch register != canary before port resume.

This workaround is disabled for omap_8250 (which uses different divisor
programming).

Credit to Doug Anderson <dianders@chromium.org> for the idea of using
the scratch register canary to discover port power-down.

Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Exar XR17V35X PCIe uarts support a 4-bit fractional divisor register.
Refactor the divisor calculation from the divisor programming.

Allow a fractional result from serial8250_get_divisor() and pass this
result to serial8250_dl_write().

Simplify the calculation for quot and quot_frac. This was verified
to be identical to the results of the original calculation with a test
jig.

NB: The results were also compared with the divisor value chart
on pg 33 of the Exar XR17V352 datasheet, rev 1.0.3, here:
http://www.exar.com/common/content/document.ashx?id=1585
which differs from the calculated values by 1 in the fractional result.
This is because the calculated values are still rounded in the
fractional result, whereas the table values are truncated. Note
that the data error rate % values in the datasheet are for
rounded fractional results, as the truncated fractional results
have more error.

Cc: Joe Schultz <jschultz@xes-inc.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor divisor register programming into a new function,
serial8250_set_divisor; this allows serial console to reinitialize
early after resume from suspend.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor the computation of the LCR register value from termios c_cflag
into a new local function, serial8250_compute_lcr().
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The UART_BUG_QUOT workaround adjusts the divisor computed from the
baud rate by serial8250_get_divisor(). Move the workaround into
serial8250_get_divisor(), so that divisor-from-baud computation
is encapsulated.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since we return in the first branch the second one doesn't require an
additional else keyword. The patch removes it.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some of FSL SoCs like T1040 has new version of UART controller which
can support 64byte FiFo.
To enable 64 byte support, following needs to be done:
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
        -FCR[RTL] = 00  1 byte
        -FCR[RTL] = 01  16 bytes
        -FCR[RTL] = 10  32 bytes
        -FCR[RTL] = 11  56 bytes
-tx_loadsz is set to 63-bytes instead of 64-bytes to implement
 workaround of errata A-008006 which states that tx_loadsz should
 be configured less than Maximum supported fifo bytes
Signed-off-by: NVijay Rai <vijay.rai@freescale.com>
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OMAP3 UART ignores MCR[1] (ie., UART_MCR_RTS) when in autoRTS
mode (UPF_HARD_FLOW + CRTSCTS). This makes it impossible for either
the serial core or userspace to manually flow control the sender.

Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.

Note that the OMAP3 UART provides no mechanism for switching from
autoRTS mode without corrupting incoming data; to access the
necessary register, the line control settings must be set to 8-e-2
and thus any data received during that time will be interpreted with
those settings. This corruption has been observed in practice.

Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Attempting to use SysRq via the 8250 serial port with spin lock
debugging on on a uniprocessor system results in the following splat:

 SysRq :
 BUG: spinlock trylock failure on UP on CPU#0, swapper/0
  lock: serial8250_ports+0x0/0x8c0, .magic: dead4ead, .owner: swapper/0, .owner_cpu: 0
 CPU: 0 PID: 0 Comm: swapper Not tainted 3.18.0-rc4+ #37
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
  ffffffff8245ba00 ffffffff81628b28 ffffffff812c8d27 ffffffff81628b48
  ffffffff8106812e ffffffff8245ba00 ffffffff814e22ed ffffffff81628b68
  ffffffff810681a6 0000000000000000 0000000000000000 ffffffff81628b88
 Call Trace:
  <IRQ>  [<ffffffff812c8d27>] dump_stack+0x19/0x1b
  [<ffffffff8106812e>] spin_dump+0x7e/0xd0
  [<ffffffff810681a6>] spin_bug+0x26/0x30
  [<ffffffff8106843c>] do_raw_spin_trylock+0x4c/0x60
  [<ffffffff812cdb1d>] _raw_spin_trylock+0x1d/0x60
  [<ffffffff812336d8>] serial8250_console_write+0x68/0x190
  [<ffffffff811eb0b0>] ? sprintf+0x40/0x50
  [<ffffffff8106ab5e>] call_console_drivers.constprop.11+0x9e/0xf0
  [<ffffffff8106b276>] console_unlock+0x3e6/0x490
  [<ffffffff8106b595>] vprintk_emit+0x275/0x530
  [<ffffffff812c869a>] printk+0x4d/0x4f
  [<ffffffff8121e612>] __handle_sysrq+0x62/0x1b0
  [<ffffffff8121e5b5>] ? __handle_sysrq+0x5/0x1b0
  [<ffffffff8121ebc6>] handle_sysrq+0x26/0x30
  [<ffffffff81233157>] serial8250_rx_chars+0x1d7/0x250
  [<ffffffff812338bb>] serial8250_handle_irq+0x7b/0x90
  [<ffffffff812338f3>] serial8250_default_handle_irq+0x23/0x30
  [<ffffffff812318b3>] serial8250_interrupt+0x63/0xe0
  [<ffffffff8106d80e>] handle_irq_event_percpu+0x4e/0x200
  [<ffffffff8106da01>] handle_irq_event+0x41/0x70
  [<ffffffff810701ee>] ? handle_edge_irq+0x1e/0x110
  [<ffffffff8107026e>] handle_edge_irq+0x9e/0x110
  [<ffffffff810041c2>] handle_irq+0x22/0x40
  [<ffffffff812d096e>] do_IRQ+0x4e/0xf0
  [<ffffffff812cf4ed>] common_interrupt+0x6d/0x6d
  <EOI>  [<ffffffff8100acbf>] ? default_idle+0x1f/0xd0
  [<ffffffff8100acbd>] ? default_idle+0x1d/0xd0
  [<ffffffff8100b61f>] arch_cpu_idle+0xf/0x20
  [<ffffffff8105c1db>] cpu_startup_entry+0x25b/0x360
  [<ffffffff812c726e>] rest_init+0xbe/0xd0
  [<ffffffff816a4dcb>] start_kernel+0x339/0x346
  [<ffffffff816a4495>] x86_64_start_reservations+0x2a/0x2c
  [<ffffffff816a4589>] x86_64_start_kernel+0xf2/0xf6
 HELP : loglevel(0-9) reboot(b) crash(c) show-all-locks(d) te...

Before ebade5e8 ("serial: 8250: Clean up the locking for -rt")
this was handled by not even attempting to try the lock if port->sysrq,
since it is known to be taken by the interrupt handler; see
https://bugzilla.kernel.org/show_bug.cgi?id=6716#c1.  Restore that
behavior.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In serial8250_rx_chars(), max_count is set to 256. Due to the
post-decrement operator used in the while() condition, the maximum
number of iterations actually 257. This is not a problem, but it is
mildly surprising if you're debugging. Use pre-decrement instead.
Signed-off-by: NFrans Klaver <frans.klaver@xsens.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no more users for this functions. All the 8250 drivers are
using the rs485 handler on serial_core instead.
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Initialize recently added rs485 fields on serial_core
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Switching to the N_PPS line discipline may require enabling
modem status interrupts; conversely switching from N_PPS may
require disabling modem status interrupts.

Affected drivers:
8250
amba-pl010
atmel

Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Three UART drivers (8250, atmel & amba-pl010) directly call their
enable_ms() method; the uart port lock must be acquired before
any h/w programming.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UART drivers which enable modem status interrupts when switching
to N_PPS line discipline need to determine if modem status
interrupts should be disabled when switching from N_PPS.
Specifically, the set_ldisc() notification needs to evaluate
UART_ENABLE_MS() which requires termios->c_cflag.

Convert in-tree UART drivers to new interface.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Ralink RT2880 SoC and its successors have an internal 8250 core. This core
needs the same quirks applied as the AMD AU1xxx uart. In addition to these
quirks, the ports memory region is only 0x100 unlike the AU1xxx which has a
size of 0x1000.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We have (or will have) custom DMA callbacks in the omap driver due to
the different behaviour in the RX and TX case. To make this work
we need a few changes in the IRQ handler to invoke the rx_handler again
after the "manual" mode or retry the tx_handler again before falling
back to the manual mode.

Heikki didn't want to see the extra hacks in the generic / default irq
handler and Peter wasn't too happy about an OMAP-only IRQ handler. The
way I planned it is to use this extra IRQ routine only in DMA case. If
Peter dislike this approach then I hope Heikki doesn't block changes in
the default IRQ handler :)
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OMAP has a few corner cases where it needs a share of kindness of
affection to do the right thing. Heikki Krogerus suggested that instead
adding the quirks into the default DMA implementation, OMAP could get
its own copy of the function. And Alan suggested the same thing so here
we go.

This patch provides callbacks for custom TX/RX DMA implementation. If
there are not setup / used, then the default (current) implementation is
used.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Right now it is possible that serial8250_tx_dma() fails and returns
-EBUSY. The caller (serial8250_start_tx()) will then enable
UART_IER_THRI which will generate an interrupt once the TX FIFO is
empty.
In serial8250_handle_irq() nothing will happen because up->dma is set
and so serial8250_tx_chars() won't be invoked. We end up with plenty of
interrupts and some "too much work for irq" output.

This patch introduces dma_tx_err in struct uart_8250_port to signal that
the last invocation of serial8250_tx_dma() failed so we can fill the TX
FIFO manually. Should the next invocation of serial8250_start_tx()
succeed then the dma_tx_err flag along with the THRI bit is removed and
DMA only usage may continue.
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

if I boot with console=ttyS0 and the omap driver is module I end up with

| console [ttyS0] disabled
| omap8250 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a 8250
| Unable to handle kernel paging request at virtual address c07a9de0
| Modules linked in: 8250_omap(+)
| CPU: 0 PID: 908 Comm: modprobe Not tainted 3.17.0-rc5+ #1593
| PC is at serial8250_console_setup+0x0/0xc8
| LR is at register_console+0x13c/0x3a4
| [<c0078788>] (register_console) from [<c02d0340>] (uart_add_one_port+0x3cc/0x420)
| [<c02d0340>] (uart_add_one_port) from [<c02d38a4>] (serial8250_register_8250_port+0x298/0x39c)
| [<c02d38a4>] (serial8250_register_8250_port) from [<bf006274>] (omap8250_probe+0x218/0x3dc [8250_omap])
| [<bf006274>] (omap8250_probe [8250_omap]) from [<c02e3424>] (platform_drv_probe+0x2c/0x5c)
| [<c02e3424>] (platform_drv_probe) from [<c02e1eac>] (driver_probe_device+0x104/0x228)
…
| [<c009fa48>] (SyS_init_module) from [<c000e6e0>] (ret_fast_syscall+0x0/0x30)
| Code: 7823603b f8314620 051b3013 491ed416 (44792204)

because serial8250_console_setup() is already gone.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Frans reworded the two comments with better English for better
understanding. His review hit the mailing list after the patch got
applied so here is an incremental update.
Reported-by: NFrans Klaver <frans.klaver@xsens.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In ST16650V2 based serial uarts, while initalizing the PM state,
LCR registers are being initialized to 0 in serial8250_set_sleep().
If console port is already initialized and being used, this will
throws garbage in the console.
Signed-off-by: NSudhir Sreedharan <ssreedharan@mvista.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

serial8250_do_startup() adds UART_IER_RDI and UART_IER_RLSI to ier.
serial8250_stop_rx() should remove both.
This is what the serial-omap driver has been doing and is now moved to
the 8250-core since it does no look to be *that* omap specific.
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Tony noticed that the old omap-serial driver picked the uart "number"
based on the hint given from device tree or platform device's id.
The 8250 based omap driver doesn't do this because the core code does
not honour the ->line argument which is passed by the driver.

This patch aims to keep the same behaviour as with omap-serial. The
function will first try to use the line suggested ->line argument and
then fallback to the old strategy in case the port is taken.

That means the the third uart will always be ttyS2 even if the previous
two have not been enabled in DT.
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The serial8250_do_startup() function unconditionally clears the
interrupts and for that it reads from the RX-FIFO without checking if
there is a byte in the FIFO or not. This works fine on OMAP4+ HW like
AM335x or DRA7.
OMAP3630 ES1.1 (which means probably all OMAP3 and earlier) does not like
this:

|Unhandled fault: external abort on non-linefetch (0x1028) at 0xfb020000
|Internal error: : 1028 [#1] ARM
|Modules linked in:
|CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-00022-g7edcb57-dirty #1213
|task: de0572c0 ti: de058000 task.ti: de058000
|PC is at mem32_serial_in+0xc/0x1c
|LR is at serial8250_do_startup+0x220/0x85c
|Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
|Control: 10c5387d  Table: 80004019  DAC: 00000015
|[<c03051d4>] (mem32_serial_in) from [<c0307fe8>] (serial8250_do_startup+0x220/0x85c)
|[<c0307fe8>] (serial8250_do_startup) from [<c0309e00>] (omap_8250_startup+0x5c/0xe0)
|[<c0309e00>] (omap_8250_startup) from [<c030863c>] (serial8250_startup+0x18/0x2c)
|[<c030863c>] (serial8250_startup) from [<c030394c>] (uart_startup+0x78/0x1d8)
|[<c030394c>] (uart_startup) from [<c0304678>] (uart_open+0xe8/0x114)
|[<c0304678>] (uart_open) from [<c02e9e10>] (tty_open+0x1a8/0x5a4)
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

While comparing the OMAP-serial and the 8250 part of this I noticed that
the latter does not use run time-pm. Here are the pieces. It is
basically a get before first register access and a last_busy + put after
last access. This has to be enabled from userland _and_ UART_CAP_RPM is
required for this.
The runtime PM can usually work transparently in the background however
there is one exception to this: After serial8250_tx_chars() completes
there still may be unsent bytes in the FIFO (depending on CPU speed vs
baud rate + flow control). Even if the TTY-buffer is empty we do not
want RPM to disable the device because it won't send the remaining
bytes. Instead we leave serial8250_tx_chars() with RPM enabled and wait
for the FIFO empty interrupt. Once we enter serial8250_tx_chars() with
an empty buffer we know that the FIFO is empty and since we are not going
to send anything, we can disable the device.
That xchg() is to ensure that serial8250_tx_chars() can be called
multiple times and only the first invocation will actually invoke the
runtime PM function. So that the last invocation of __stop_tx() will
disable runtime pm.

NOTE: do not enable RPM on the device unless you know what you do! If
the device goes idle, it won't be woken up by incomming RX data _unless_
there is a wakeup irq configured which is usually the RX pin configure
for wakeup via the reset module. The RX activity will then wake up the
device from idle. However the first character is garbage and lost. The
following bytes will be received once the device is up in time. On the
beagle board xm (omap3) it takes approx 13ms from the first wakeup byte
until the first byte that is received properly if the device was in
core-off.

v5…v8:
	- drop RPM from serial8250_set_mctrl() it will be used in
	  restore path which already has RPM active and holds
	  dev->power.lock
v4…v5:
	- add a wrapper around rpm function and introduce UART_CAP_RPM
	  to ensure RPM put is invoked after the TX FIFO is empty.
v3…v4:
	- added runtime to the console code
	- removed device_may_wakeup() from serial8250_set_sleep()

Cc: mika.westerberg@linux.intel.com
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OMAP UART provides support for HW assisted flow control. What is
missing is the support to throttle / unthrottle callbacks which are used
by the omap-serial driver at the moment.
This patch adds the callbacks. It should be safe to add them since they
are only invoked from the serial_core (uart_throttle()) if the feature
flags are set.
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit: e676253b [3/21] serial/8250: Add
support for RS485 IOCTLs, adds a building error on arch m32r.

All error/warnings:

   drivers/tty/serial/8250/8250_core.c: In function 'serial8250_ioctl':
>> drivers/tty/serial/8250/8250_core.c:2859:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
      if (copy_from_user(&rs485_config, (void __user *)arg,
      ^
>> drivers/tty/serial/8250/8250_core.c:2871:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
      if (copy_to_user((void __user *)arg, &up->rs485,
      ^
   cc1: some warnings being treated as errors
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OMAP version of the 8250 can actually use 1:1 serial8250_startup().
However it needs to be extended by a wake up irq which should to be
requested & enabled at ->startup() time and disabled at ->shutdown() time.

v2…v3: properly copy callbacks
v1…v2: add shutdown callback
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no way to access a struct uart_8250_port for a specific
line. This is only required outside of the 8250/uart callbacks like for
devices' suspend & remove callbacks. For those the 8250-core provides a
wrapper like serial8250_unregister_port() which passes the struct
to the proper function based on the line argument.

For run time suspend I need access to this struct not only to make
serial_out() work but also to properly restore up->ier and up->mcr.
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Existing callers of serial8250_modem_status() [1] hold the uart port
lock; document.

[1] In-tree callers of serial8250_modem_status()

drivers/tty/serial/8250/8250_fsl.c
  fsl8250_handle_irq()

drivers/tty/serial/8250/8250_core.c
  serial8250_handle_irq()
  serial8250_console_write()
  serial8250_get_mctrl() *

* Call graphs for callers of serial8250_get_mctrl() from the function
  which acquires the uart port lock

drivers/tty/serial/serial_core.c
  uart_port_startup()
  uart_tiocmget()
  uart_set_termios()
  uart_carrier_raised()
    ops->get_mctrl() ---> serial8250_get_mctrl()
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 06aa82e4.
This commit purports to enable auto CTS flow control for the 8250
UART driver. However, the 8250 UART driver already supports auto
CTS flow control via UART_CAP_AFE and UART_CAP_EFR. Indeed, this
patch introduces another DT attribute for which an existing firmware
flag already exists ("auto-flow-control"). Furthermore, the use of
UPF_HARD_FLOW requires the UART driver to define .throttle and
.unthrottle methods, neither of which are defined for the 8250 UART
driver (which will result in a NULL ptr dereference). Finally, this patch
supposes to fix existing bugs in the serial core for auto CTS-enabled
hardware, but does not include the class of hardware for which these
bugs exist.

CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch allow the users of the 8250 infrastructure to define a
handler for RS485 configration.

If no handler is defined the 8250 driver will work as usual.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
--
v2:Change suggested by Alan "One Thousand Gnomes":
- Move rs485 structure further down on the uart_8250_port structure

 drivers/tty/serial/8250/8250_core.c | 39 +++++++++++++++++++++++++++++++++++++
 include/linux/serial_8250.h         |  3 +++
 2 files changed, 42 insertions(+)
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add flags field to struct kernel_params, and add the first flag: unsafe
parameter. Modifying a kernel parameter with the unsafe flag set, either
via the kernel command line or sysfs, will issue a warning and taint the
kernel.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Jon Mason <jon.mason@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Add tunable RX interrupt trigger I/F of FIFO buffers.

Serial devices are used as not only message communication devices but control
or sending communication devices. For the latter uses, normally small data
will be exchanged, so user applications want to receive data unit as soon as
possible for real-time tendency. If we have a sensor which sends a 1 byte data
each time and must control a device based on the sensor feedback, the RX
interrupt should be triggered for each data.

According to HW specification of serial UART devices, RX interrupt trigger
can be changed, but the trigger is hard-coded. For example, RX interrupt trigger
in 16550A can be set to 1, 4, 8, or 14 bytes for HW, but current driver sets
the trigger to only 8bytes.

This patch makes some devices change RX interrupt trigger from userland.

<How to use>
- Read current setting
 # cat /sys/class/tty/ttyS0/rx_trig_bytes
 8

- Write user setting
 # echo 1 > /sys/class/tty/ttyS0/rx_trig_bytes
 # cat /sys/class/tty/ttyS0/rx_trig_bytes
 1

<Support uart devices>
- 16550A and Tegra (1, 4, 8, or 14 bytes)
- 16650V2 (8, 16, 24, or 28 bytes)
- 16654 (8, 16, 56, or 60 bytes)
- 16750 (1, 16, 32, or 56 bytes)

<Change log>
Changes in V9:
 - Use attr_group instead of dev_spec_attr_group of uart_port structure

Changes in V8:
 - Divide this patch from V7's patch based on Greg's comment

Changes in V7:
 - Add Documentation
 - Change I/F name from rx_int_trig to rx_trig_bytes because the name
   rx_int_trig is hard to understand how users specify the value

Changes in V6:
 - Move FCR_RX_TRIG_* definition in 8250.h to include/uapi/linux/serial_reg.h,
   rename those to UART_FCR_R_TRIG_*, and use UART_FCR_TRIGGER_MASK to
   UART_FCR_R_TRIG_BITS()
 - Change following function names:
    convert_fcr2val() => fcr_get_rxtrig_bytes()
    convert_val2rxtrig() => bytes_to_fcr_rxtrig()
 - Fix typo in serial8250_do_set_termios()
 - Delete the verbose error message pr_info() in bytes_to_fcr_rxtrig()
 - Rename *rx_int_trig/rx_trig* to *rxtrig* for several functions or variables
   (but UI remains rx_int_trig)
 - Change the meaningless variable name 'val' to 'bytes' following functions:
    fcr_get_rxtrig_bytes(), bytes_to_fcr_rxtrig(), do_set_rxtrig(),
    do_serial8250_set_rxtrig(), and serial8250_set_attr_rxtrig()
 - Use up->fcr in order to get rxtrig_bytes instead of rx_trig_raw in
   fcr_get_rxtrig_bytes()
 - Use conf_type->rxtrig_bytes[0] instead of switch statement for support check
   in register_dev_spec_attr_grp()
 - Delete the checking whether a user changed FCR or not when minimum buffer
   is needed in serial8250_do_set_termios()

Changes in V5.1:
 - Fix FCR_RX_TRIG_MAX_STATE definition

Changes in V5:
 - Support Tegra, 16650V2, 16654, and 16750
 - Store default FCR value to up->fcr when the port is first created
 - Add rx_trig_byte[] in uart_config[] for each device and use rx_trig_byte[]
   in convert_fcr2val() and convert_val2rxtrig()

Changes in V4:
 - Introduce fifo_bug flag in uart_8250_port structure
   This is enabled only when parity is enabled and UART_BUG_PARITY is enabled
   for up->bugs. If this flag is enabled, user cannot set RX trigger.
 - Return -EOPNOTSUPP when it does not support device at convert_fcr2val() and
   at convert_val2rxtrig()
 - Set the nearest lower RX trigger when users input a meaningless value at
   convert_val2rxtrig()
 - Check whether p->fcr is existing at serial8250_clear_and_reinit_fifos()
 - Set fcr = up->fcr in the begging of serial8250_do_set_termios()

Changes in V3:
 - Change I/F from ioctl(2) to sysfs(rx_int_trig)

Changed in V2:
 - Use _IOW for TIOCSFIFORTRIG definition
 - Pass the interrupt trigger value itself
Signed-off-by: NYoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>