Currently firmware is configured to filter out beacons. In case
a beacon was changed - it is waking the host.
However, some vendors change their IEs frequently without any
significant change, and redundant wakeups are triggered as a
result.
As a solution disable beacon filtering when entering d0i3.
Instead, firmware will store the latest beacon and upon exiting
d0i3 it will send it up to the host, so the host can act upon
changes (if there were any).
This beacon will arrive as a dedicated notification - support it
as well.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New functionality for testing that is not relevant for
this driver has been added. This required an API change.

Add new cmd & response versions for the MCC update cmd & response.
Add new TLV indicating that the FW is using the new API.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Host commands now have a group id, express this in printed messages.
Signed-off-by: NSharon Dvir <sharon.dvir@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Define the RX API that's used by the 9000 series hardware.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add ability to set the continuous recording mode of the FW, while
the FW debug data is configured to be stored on the NIC.
This could be useful for storing large segments of FW usniffer
debug data on the host, while having small store space on the NIC.
The host receives the usniffer data through the regular RX path, and
the data can get extracted using trace-cmd.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since the 8000 series, the DTS measurement request command has been
changed. Use an ucode capability flag to determine which version is
supported and send the extended command when needed.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Move the DTS measurement command and notification from short
command header to the new PHY command group for firmware
supporting the extended command headers.
Signed-off-by: NAviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The RX API is currently mixed up into the general fw-api.h
file, but we're going to need to extend it significantly in
the future, so move it to its own file.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Remove some unused values from the RX API; these were used
with older firmware API that didn't have the RX energy API,
support for which was removed a long time ago.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

ECHO_CMD is a simple command that can be sent to the
firmware just to check that it is alive.
This command is useful for debug purpose, provide a debugfs
hook to send it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.

In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.

When the device is slave on the bus(SDIO) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. When the FW wants load / unload pages, it creates an
interrupt,	and the driver uploads / downloads the page to an address in
the a specific address on the device's memory.

The driver can support up to 1 MB of pages.

Add paging mechanism for the UMAC on SDIO in order to allow the program to
use a larger virtual space while using less physical memory on the device
itself.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.

In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.

When the device is master on the bus(PCI) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. The FW can load / unload the pages on its own.

The driver can support up to 1 MB of pages.

Add paging mechanism for the UMAC on PCI in order to allow the program
to use a larger virtual space while using less physical memory on the
device.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

TCP software implementation on the host requires extensive computing
power.  Offloading even some of the TCP/IP stack to the NIC might save
a significant overhead. In order to enable this feature on our hw,
we need to configure it first. Once done, we mark this capability,
to be advertised later to the OS via ieee80211_register_hw.
The driver Rx indications for TCP Checksum is integrated within the
standard Rx status. The driver responds to those indications as follows:
If the frame was tested by hw and checksum ok report CHECKSUM_UNNECESSARY.
Otherwise, report CHECKSUM_NONE.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ToF is a time based method for measurement of the WiFi device
location within a WiFi environment. The driver functionality provided
by this patch is the interface for communication with FW and receiving
location related updates from the FW. The interface provided by this
patch is via debugfs.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add DC2DC_CONFIG_CMD (0x83) cmd.

Add IWL_UCODE_TLV_CAPA_DC2DC_CONFIG_SUPPORT tlv.

The command allows the driver get & set the DCDC's frequency tune.
(freq_tune is the divider that is used to calculate the actual DCDC's
clock rate)
The command always returns the current/updated frequency tune values of
the DCDC.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmwares that used these commands is not supported
anymore. Remove them.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add UMAC scan iteration complete notification. This notification can
be enabled by setting scan_iter_notif_enabled through debugfs.
Upon receiving this notification, print the list of channels that
have been scanned in this iteration. This is useful for debugging.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware doesn't relate the scan to a vif. The scan is
run by a separate entity called auxiliary MAC (aka AUX MAC).
This AUX MAC needs to get Tx power limitations that are
not applied on a specific vif, but on the device as a whole.

This can be implemented by using the minimum of all the
values set by the user for all the MACs. But then we need
to ignore the limitations that come from the AP or
regulatory for a specific vif: a specific vif might have
regulatory limitations because of the channel is works on.
This limit is irrelevant for the AUX MAC.
Use the new API from mac80211: the user_power_level in
bss_conf to achieve this.

Firmware -13.ucode has already moved to this API.

Change-Id: Ifba83660f378e91b93bd46d29fe8ba35a7c168a4
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We previously enabled the smart FIFO (SF) in BSS only after
association.
This cause interrupt latency on P2P on certain devices.
Change the working model to enable the SF all the time and
play with the timeout values based on the association state.
This change was not tested on older firwmares, so make it
happen only on -13.ucode and up.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When moving to the D3 FW give it the valid MCC from the D0 FW. When
returning from D3 to D0, query the D3 FW for the latest MCC, as
it might have changed internally. This MCC will be replayed to the D0 FW
when it boots.
Signed-off-by: NJonathan Doron <jonathanx.doron@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For some configurations, the driver should get the MAC
address from the hardware registers and not from the
regular locations. Since the parsing of the MAC address
is the same regardless of its source, continue the regular
code path (parsing) after we read the registers.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Starting from family 8000 B0 step the radio_cfg parameters
and the get_sku parameters moved from SW section to PHY_SKU section.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Chub (Communication Hub, CommsHUB) is a HW component that connects to the cellular
and connectivity cores that gets updates of mcc changes, and then notifies the FW
directly of any mcc change.

The ucode notifies the driver (via this command) that it should ask for an mcc update,
and the driver sends the ucode the update mcc command to set the updated regulatory info.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The new API sets an MCC (mobile country code) to FW and receives a
channel structure to be used as a basis for an updated regulatory domain.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The new API slightly changes the layout of the version of
the firmware - prepare for that.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Export the radio statistics from the statistics v10 API (if the
firmware also has the capability to fill these statistics) using
the global survey data facility.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware API structs are split differently, synchronize
the struct splits with the current firmware definitions.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the FW is in error status - try to read the RXF and
TXF (all of them) and add them to the dump data.

This shouldn't happen in non-error statuses, as we don't
want to stop the RXF/TXF while they are running.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A new host command can be used to configure the scheduler
instead of accessing the scheduler's registers from the
driver. This is easier and less error prone since accessing
the hardware at certain moments can lead to races with the
firmware.
Prefer to use the host command whenever it is available.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Interoperability issues were identified and root caused to
the Smart Fifo watermarks. These issues arose with
NetGear R7000. Fix this.

Cc: <stable@vger.kernel.org> [3.14+]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Query the firmware for scan offload matches when waking up in order to
report net detect as the reason for the wake up.

This requires a new command API to be implemented.  Additionally,
remove some net detect command entries that are not valid anymore.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support to MFUART loading notification (print notification
data with IWL_DEBUG_INFO)
Signed-off-by: NChaya Rachel Ivgy <chaya.rachel.ivgi@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Send a dedicated TDLS_CONFIG command when a TDLS peer joins/leaves. The
fields for the command are mostly place-holders, as most of the FW
functionality is not implemented. In the future the dedicated FW TID
will be used for channel-switching and buffer-sta functionality.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a channel-switch command and a switch-start notification. Also add a
FW TLV bit indicating TDLS channel switching support.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This API uses second CPU scan commands, and can support multiple
simultaneous scans.

Adding the new API, and adding new mechanisms to deal with up to
8 simultaneous scans instead of the old scan status.

New scan API requires scan configuration for default scan parameters,
adding it in _up flow. Also updating scan configuration after updating
valid scan antennas via debugfs.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.

Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>