Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

commit 86271e46 introduced a
regression that caused mac80211 queues in stopped state.

ath_drain_all_txq is called in driver flush which would reset
the stopped flag and the mac80211 queues were never started
after that. iperf traffic is completely stalled due to this issue.

Restart the mac80211 queues in driver flush only if the txqs were
drained.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the recent tx status optimization in mac80211, we bail out as
and and when invalid rate index is found. So the behavior of resetting
rate idx to -1 and count to 0 has changed for the rate indexes that
were not part of the driver's retry series.

This has resulted in ath9k using incorrect rate table index which
caused the system to panic. Ideally ath9k need to loop only for the
indexes that were part of the retry series and so simply use hw->max_rates
as the loop counter.

Pasted the stack trace of the panic issue for reference.

[  754.093192] BUG: unable to handle kernel paging request at ffff88046a9025b0
[  754.093256] IP: [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
[  754.094888] Call Trace:
[  754.094903]  <IRQ>
[  754.094928]  [<ffffffffa051f883>] ieee80211_tx_status+0x203/0x9e0 [mac80211]
[  754.094975]  [<ffffffffa053e305>] ? __ieee80211_wake_queue+0x125/0x140 [mac80211]
[  754.095017]  [<ffffffffa02e66c9>] ath_tx_complete_buf+0x1b9/0x370 [ath9k]
[  754.095054]  [<ffffffffa02e6fcf>] ath_tx_complete_aggr+0x51f/0xb50 [ath9k]
[  754.095098]  [<ffffffffa05382a3>] ? ieee80211_prepare_and_rx_handle+0x173/0xab0 [mac80211]
[  754.095148]  [<ffffffff81350e62>] ? _raw_spin_unlock_irqrestore+0x32/0x40
[  754.095186]  [<ffffffffa02e9735>] ath_tx_tasklet+0x365/0x4b0 [ath9k]
[  754.095224]  [<ffffffff8107a2a2>] ? clockevents_program_event+0x62/0xa0
[  754.095261]  [<ffffffffa02e2628>] ath9k_tasklet+0x168/0x1c0 [ath9k]
[  754.095298]  [<ffffffff8105599b>] tasklet_action+0x6b/0xe0
[  754.095331]  [<ffffffff81056278>] __do_softirq+0x98/0x120
[  754.095361]  [<ffffffff8100cd5c>] call_softirq+0x1c/0x30
[  754.095393]  [<ffffffff8100efb5>] do_softirq+0x65/0xa0
[  754.095423]  [<ffffffff810563fd>] irq_exit+0x8d/0x90
[  754.095453]  [<ffffffff8100ebc1>] do_IRQ+0x61/0xe0
[  754.095482]  [<ffffffff81351413>] ret_from_intr+0x0/0x15
[  754.095513]  <EOI>
[  754.095531]  [<ffffffff81014375>] ? native_sched_clock+0x15/0x70
[  754.096475]  [<ffffffffa02bcfa6>] ? acpi_idle_enter_bm+0x24d/0x285 [processor]
[  754.096475]  [<ffffffffa02bcf9f>] ? acpi_idle_enter_bm+0x246/0x285 [processor]
[  754.096475]  [<ffffffff8127fab2>] cpuidle_idle_call+0x82/0x100
[  754.096475]  [<ffffffff8100a236>] cpu_idle+0xa6/0xf0
[  754.096475]  [<ffffffff81339bc1>] rest_init+0x91/0xa0
[  754.096475]  [<ffffffff814efccd>] start_kernel+0x3fd/0x408
[  754.096475]  [<ffffffff814ef347>] x86_64_start_reservations+0x132/0x136
[  754.096475]  [<ffffffff814ef451>] x86_64_start_kernel+0x106/0x115
[  754.096475] RIP  [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On hardware busy the scan request pointer should be cleared, as higher
levels will release. This avoids a crash when that pointer is
erroneously used later.
Signed-off-by: NJoseph J. Gunn <armadefuego@yahoo.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clearly a mistake, since pointers won't suddenly
change their value...
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kernel panic occurs just after AR2427 establishes connection with AP.
Unless aggregation is enabled we don't initialize the TID structure.
Thus accesing the elements of the TID structure when aggregation is
disabled, leads to NULL pointer dereferencing.

[  191.320358] Call Trace:
[  191.320364]  [<fd250ea7>] ? ath9k_tx+0xa7/0x200 [ath9k]
[  191.320376]  [<fd1ec7fc>] ? __ieee80211_tx+0x5c/0x1e0 [mac80211]
[  191.320386]  [<fd1edd2b>] ? ieee80211_tx+0x7b/0x90 [mac80211]
[  191.320395]  [<fd1edddd>] ? ieee80211_xmit+0x9d/0x1d0 [mac80211]
[  191.320401]  [<c014218f>] ? wake_up_state+0xf/0x20
[  191.320405]  [<c015dbc8>] ? signal_wake_up+0x28/0x40
[  191.320410]  [<c012a578>] ? default_spin_lock_flags+0x8/0x10
[  191.320420]  [<fd1ee308>] ? ieee80211_subif_start_xmit+0x2e8/0x7c0
[mac80211]
[  191.320425]  [<c058f905>] ? do_page_fault+0x295/0x3a0
[  191.320431]  [<c04c4a3d>] ? dev_hard_start_xmit+0x1ad/0x210
[  191.320436]  [<c04d96b5>] ? sch_direct_xmit+0x105/0x170
[  191.320445]  [<fd1f161a>] ? get_sta_flags+0x2a/0x40 [mac80211]
[  191.320449]  [<c04c780f>] ? dev_queue_xmit+0x37f/0x4b0
[  191.320452]  [<c04d75b0>] ? eth_header+0x0/0xb0
[  191.320456]  [<c04cc479>] ? neigh_resolve_output+0xe9/0x310
[  191.320461]  [<c053d295>] ? ip6_output_finish+0xa5/0x110
[  191.320464]  [<c053e354>] ? ip6_output2+0x134/0x250
[  191.320468]  [<c053f7dd>] ? ip6_output+0x6d/0x100
[  191.320471]  [<c0559665>] ? mld_sendpack+0x395/0x3e0
[  191.320475]  [<c0557f81>] ? add_grhead+0x31/0xa0
[  191.320478]  [<c055a83c>] ? mld_send_cr+0x1bc/0x2b0
[  191.320482]  [<c01535d9>] ? irq_exit+0x39/0x70
[  191.320485]  [<c055a940>] ? mld_ifc_timer_expire+0x10/0x40
[  191.320489]  [<c015b92e>] ? run_timer_softirq+0x13e/0x2c0
[  191.320493]  [<c0103a30>] ? common_interrupt+0x30/0x40
[  191.320498]  [<c055a930>] ? mld_ifc_timer_expire+0x0/0x40
[  191.320502]  [<c0153358>] ? __do_softirq+0x98/0x1b0
[  191.320506]  [<c01534b5>] ? do_softirq+0x45/0x50
[  191.320509]  [<c0153605>] ? irq_exit+0x65/0x70
[  191.320513]  [<c05917dc>] ? smp_apic_timer_interrupt+0x5c/0x8b
[  191.320516]  [<c0103df1>] ? apic_timer_interrupt+0x31/0x40
[  191.320521]  [<c016007b>] ? k_getrusage+0x12b/0x2f0
[  191.320525]  [<c039e384>] ? acpi_idle_enter_simple+0x117/0x148
[  191.320529]  [<c04a20da>] ? cpuidle_idle_call+0x7a/0x100
[  191.320532]  [<c01021d4>] ? cpu_idle+0x94/0xd0
[  191.320536]  [<c057ab88>] ? rest_init+0x58/0x60
[  191.320541]  [<c07a58ec>] ? start_kernel+0x351/0x357
[  191.320544]  [<c07a53c7>] ? unknown_bootoption+0x0/0x19e
[  191.320548]  [<c07a50aa>] ? i386_start_kernel+0xaa/0xb1
[  191.320550] Code: 03 66 3d 00 03 0f 84 7c 02 00 00 83 c3 18 0f b6 03
8b 4d e0 89 c3 83 e3 0f 6b c3 48 89 5d d8 8d 04 06 8d 50 0c 89 55 d0 8b
40 20 <8b> 00 3b 01 0f 85 8e 02 00 00 f6 47 20 40 0f 84 29 ff ff ff 8b
[  191.320634] EIP: [<fd2586d4>] ath_tx_start+0x474/0x770 [ath9k] SS:ESP
0068:c0761a90
[  191.320642] CR2: 0000000000000000
[  191.320647] ---[ end trace 9296ef23b9076ece ]---
[  191.320650] Kernel panic - not syncing: Fatal exception in interrupt

Cc: stable@kernel.org
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These were found using the following semantic match:
// <smpl>
@@expression E1; type T;@@
* memset(E1, ... * sizeof(T) * ..., ...);
// </smpl>

Also take this opportunity to remove the unnecessary void* casts.
Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add unknown Toshiba device, mentioned in rt3572sta sources, under
CONFIG_RT2800USB_UNKNOWN
Signed-off-by: NPeter Lemenkov <lemenkov@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add 2L Central Europe BV 8070 under CONFIG_RT2800USB_UNKNOWN
Signed-off-by: NPeter Lemenkov <lemenkov@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add Planex Communications, Inc. RT8070 under CONFIG_RT2800USB_UNKNOWN
Signed-off-by: NPeter Lemenkov <lemenkov@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ID for Asus USB-N11 Wi-FI adapter. Tested by me.
Signed-off-by: NPeter Lemenkov <lemenkov@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removing an entry from the scan_list should be performed while holding
the lock.
Signed-off-by: NJoseph J. Gunn <armadefuego@yahoo.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We should unlock here instead of returning -EINVAL directly.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NTõnu Samuel <tonu@jes.ee>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: Nmatt mooney <mfm@muteddisk.com>
Acked-by: NWANG Cong <xiyou.wangcong@gmail.com>
Acked-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

Some clients seems to keep track of their reorder window even after an
aggregation session has been disabled. This causes issues if there are
still retried but not completed frames pending for the TID.
To ensure that rx does not stall in such situations, set sendbar to 1
for any frame purged from the TID queue on teardown.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k calls ath9k_hw_stoptxdma every time it sends a beacon, however there
is not much point in doing that if the previous beacon and mcast traffic
went out properly. On AR9380, calling that function too often can result
in an increase of stuck beacons due to differences in the handling of the
queue enable/disable functionality.

With this patch, the queue will only be explicitly stopped if the previous
data frames were not sent successfully. With the beacon code being the
only remaining user of ath9k_hw_stoptxdma, this function can be simplified
in order to remove the now pointless attempts at waiting for transmission
completion, which would never happen at this point due to the different
method of tx scheduling of the beacon queue.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch simplifies the flush op and reuses ath_drain_all_txq for
flushing out pending frames if necessary. It also uses a global timeout
of 200ms instead of the per-queue 60ms timeout.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some situations, stopping Tx DMA frequently fails, leading to messages
like this:

ath: Failed to stop TX DMA in 100 msec after killing last frame
ath: Failed to stop TX DMA!

This patch uses a few MAC features to abort DMA globally instead of iterating
over all hardware queues and attempting to stop them individually.
Not only is that faster and works with a shorter timeout, it also makes the
process much more reliable.

With this change, I can no longer trigger these messages on AR9380,
and on AR9280 they become much more rare.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

set_ringparam only allows changes to tx ring at this time.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support to iwlagn for off-channel TX. The
microcode API for this is a bit strange in that
it uses a hacked-up scan command, so the scan
code needs to change quite a bit to accomodate
that and be able to send it out.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

defs.meshie.val.mesh_id is 32 chars long.  It's not supposed to be NUL
terminated.  This code puts a terminator on the end to make it easier to
print to sysfs.  The problem is that if the mesh_id fills the entire
buffer the original code puts the terminator one spot past the end.

The way the original code was written, there was a check to make sure
that maxlen was less than PAGE_SIZE.  Since we know that maxlen is at
most 34 chars, I just removed the check.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Increasing the wait count makes the nf load pass in
most of the cases.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Increase the delay to make sure the initialization of pll
passes.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set some GPIO pins to Pull-down mode to save power.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hardware rx filter flag triggered by FIF_PROMISC_IN_BSS is overly broad
and covers even frames with PHY errors. When this flag is enabled, this message
shows up frequently during scanning or hardware resets:

ath: Could not stop RX, we could be confusing the DMA engine when we start RX up

Since promiscuous mode is usually not particularly useful, yet enabled by
default by bridging (either used normally in 4-addr mode, or with hacks
for various virtualization software), we should sacrifice it for better
reliability during normal operation.

This patch leaves it enabled if there are active monitor mode interfaces, since
it's very useful for debugging.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While working on PS I've noticed elp_work is kicking rather often, and
sometimes the chip is put to sleep before 5ms delay expires. This
seems to happen because by the time wl1251_ps_elp_wakeup is called
elp_work might still be pending. After wakeup is done, the processing
may take some time, during which 5ms might expire and elp_work might
get scheduled. In this case, ss soon as 1st thread finishes work and
releases the mutex, elp_work will then put the device to sleep without
5ms delay. In addition 1st thread will queue additional elp_work
needlessly.

Fix this by cancelling work in wl1251_ps_elp_wakeup instead.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl1251_ps_set_elp() only does acx_sleep_auth call and takes the chip
from/to ELP, however all callers of wl1251_ps_set_mode() have already
taken the chip out of ELP and puts it back to ELP when they finish.
This makes ELP calls (and register writes they result in) superfluous.

So remove wl1251_ps_set_elp function and call acx_sleep_auth directly.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This just matches reality...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NBob Copeland <me@bobcopeland.com>

and make use of it in wireless drivers
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use kcalloc or kzalloc rather than the combination of kmalloc and memset.

Thanks coccicheck for detecting this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This updates the p54spi Kconfig help text.
The driver works well on n8x0, so remove the words "experimental" and "untested".
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My commit 466a19a0 "iwlwifi: move rx
handlers code to iwl-rx.c" breaks compilation on 32 bits. Fix that.
Reported-by: NGuy, Wey-Yi <wey-yi.w.guy@intel.com>
Reported-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It seems ath5k has issues receiving broadcast packets (ARPs) when
using multiple STA interfaces associated with multiple APs.
This patch ensures the NIC is always in PROMISC mode if there
are more than 1 stations associated.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Usually H/W generate statistics notify once per about 100ms, but
sometimes we can receive notify in shorter time, even 2 ms.

This can be problem for plcp health and ack health checking.

I.e. with 2 plcp errors happens randomly in 2 ms duration, we
exceed plcp delta threshold equal to 100 (2*100/2).

Also checking ack's in short time, can results not necessary false
positive and firmware reset, for example when channel is noised and
we do not receive ACKs frames or when remote device does not send
ACKs at the moment.

Patch change code to do statistic check and possible recovery only
if 99ms elapsed from last check. Forced delay should assure we have
good statistic data to estimate hardware state.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make iwl_good_plcp_health code easiest to read.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Put generic rx_handlers (except iwlagn_rx_reply_compressed_ba) to
iwl-rx.c . Make functions static and change prefix from iwlagn_ to
iwl_ . Beautify iwl_setup_rx_handlers and do some other minor coding
style changes.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>