This patch adds functions stubs to support EEE on/off.
Signed-off-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

>From RTL8168e-vl the value in register MaxTxPacketSize is interpreted
differently, therefore use new helper rtl_is_8168evl_up to set this
register.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add helper rtl_is_8168evl_up to make the code better readable and to
simplify it.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tp->coalesce_info is used in rtl_coalesce_info() only, so we can
remove this member. In addition replace phy_ethtool_get_link_ksettings
with a direct access to tp->phydev->speed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of a timeout currently ~0 is returned. Callers often just check
whether a certain bit is set and therefore may behave incorrectly.
So let's return -ETIMEDOUT in case of a timeout.

r8168_phy_ocp_read is used in r8168g_mdio_read only, therefore we can
apply the same change.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were accessing the pointer returned from platform_get_resource before
checking if it was valid, causing an oops if it was not. Move this access
after the call to devm_ioremap_resource which does the validity check.
Signed-off-by: NRobert Hancock <hancock@sedsystems.ca>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize the PTP physical hardware clock.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement physical hardware clock operations.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MTPPS register provides the device PPS capabilities, configure the PPS
in and out modules and holds the PPS in time stamp.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MTUTC register configures the HW UTC counter.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Query free running clock PCI BAR and offsets during the pci_init.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two new bus operations for reading the hardware free running clock.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add free running clock PCI BAR and offset to query firmware command.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert everything to phylink.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Start adding the phylink callbacks.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for the convertion, split the adjust_link function into
mac_config and add the mac_link_up and mac_link_down functions.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/net/ethernet/qlogic/qede/qede_main.c:963:6:
 warning: symbol 'qede_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qede/qede_main.c:969:6:
 warning: symbol 'qede_unlock' was not declared. Should it be static?
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update driver version to match device specification.
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let the compiler decide if the function should be inline in *.c files
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the set_ringparam() function of the ethtool interface
to enable the changing of io queue sizes.
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there is not enough memory to allocate io queues the driver will
try to allocate smaller queues.

The backoff algorithm is as follows:

1. Try to allocate TX and RX and if successful.
1.1. return success

2. Divide by 2 the size of the larger of RX and TX queues (or both if their size is the same).

3. If TX or RX is smaller than 256
3.1. return failure.
4. else
4.1. go back to 1.

Also change the tx_queue_size, rx_queue_size field names in struct
adapter to requested_tx_queue_size and requested_rx_queue_size, and
use RX and TX queue 0 for actual queue sizes.
Explanation:
The original fields were useless as they were simply used to assign
values once from them to each of the queues in the adapter in ena_probe().
They could simply be deleted. However now that we have a backoff
feature, we have use for them. In case of backoff there is a difference
between the requested queue sizes and the actual sizes. Therefore there
is a need to save the requested queue size for future retries of queue
allocation (for example if allocation failed and then ifdown + ifup was
called we want to start the allocation from the original requested size of
the queues).
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently ethtool -g shows the same size for current and max queue
sizes.
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use MAX_QUEUES_EXT get feature capability to query the device.
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new admin command to support different queue size for Tx/Rx
queues (the change also support different SQ/CQ sizes)
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement mqprio qdisc support by mapping traffic classes to
different hardware enqueue priorities. The maximum number of
supported traffic classes is an attribute of each DPNI object.

The traffic classes map to hardware priorities from highest (0)
to lowest (highest prio number). The skb priority information
received from the stack is used to select the hardware Tx queue
on which to enqueue the frame.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NBogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DPNI objects can have multiple traffic classes, as reflected by
the num_tc attribute. Until now we ignored its value and only
used traffic class 0.

This patch adds support for multiple Tx traffic classes; we have
num_queues x num_tcs hardware queues available for each interface.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the code configuring xps on the netdev TX queues to a
separate function. A subsequent patch will need to call
this in another context as well.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add dependency to TI CPTS from Common CLK framework COMMON_CLK to fix
allyesconfig build for Powerpc:

drivers/net/ethernet/ti/cpts.c: In function 'cpts_of_mux_clk_setup':
drivers/net/ethernet/ti/cpts.c:567:2: error: implicit declaration of function 'of_clk_parent_fill'; did you mean 'of_clk_get_parent_name'? [-Werror=implicit-function-declaration]
  of_clk_parent_fill(refclk_np, parent_names, num_parents);
  ^~~~~~~~~~~~~~~~~~
  of_clk_get_parent_name

Fixes: a3047a81 ("net: ethernet: ti: cpts: add support for ext rftclk selection")
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The w5X00 chip provides an SPI to Ethernet inteface. This patch allows
platform devices to be defined through the device tree.
Signed-off-by: NNicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When TCP stream gets out of sync (driver stops receiving skbs
with expected TCP sequence numbers) request a TX resync from
the kernel.

We try to distinguish retransmissions from missed transmissions
by comparing the sequence number to expected - if it's further
than the expected one - we probably missed packets.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently only RX direction is ever resynced, however, TX may
also get out of sequence if packets get dropped on the way to
the driver.  Rename the resync callback and add a direction
parameter.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set ethtool TLS RX feature based on NIC capabilities, and enable
TLS RX when connections are added for decryption.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable kernel-controlled RX resync and propagate TLS connection
RX resync from kernel TLS to firmware.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some control messages must be sent from atomic context.  The mailbox
takes sleeping locks and uses a waitqueue so add a "posted" version
of communication.

Trylock the semaphore and if that's successful kick of the device
communication.  The device communication will be completed from
a workqueue, which will also release the semaphore.

If locks are taken queue the message and return.  Schedule a
different workqueue to take the semaphore and run the communication.
Note that the there are currently no atomic users which would actually
need the return value, so all replies to posted messages are just
freed.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need the name nfp_ccm_mbox_alloc() for allocating the mailbox
communication channel itself.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware indicates when a packet has been decrypted by reusing the
currently unused BPF flag.  Transfer this information into the skb
and provide a statistic of all decrypted segments.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TLS offload code casts record number to a u64.  The buffer
should be aligned to 8 bytes, but its actually a __be64, and
the rest of the TLS code treats it as big int.  Make the
offload callbacks take a byte array, drivers can make the
choice to do the ugly cast if they want to.

Prepare for copying the record number onto the stack by
defining a constant for max size of the byte array.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the code by removing struct rtl_cfg_info. Only info we need
per PCI ID is whether it supports GBit or not.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To prepare removal of struct rtl_cfg_info, set the coalesce
config based on the chip version number.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the latest changes we don't need separate functions
rtl_hw_start_8168 and rtl_hw_start_8101 any longer. This allows us to
simplify the code. For this change we need to move rtl_hw_start() and
rtl_hw_start_8169(). rtl_hw_start_8169() is unchanged.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>