Set addr_assign_type correctly to NET_ADDR_RANDOM in case
a random MAC address was generated and assigned to the netdevice.

Fix error handling in atl1c_probe(). If atl1c_read_mac_addr()
couldn't get the hw mac address, and a random mac address get
set return the error code. Don't go to err_eeprom in
atl1c_probe(), use the generated MAC address in this case.

Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.

v2: use bitops
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set addr_assign_type correctly to NET_ADDR_RANDOM in case
a random MAC address was generated and assigned to the netdevice.

Fixed ethoc_set_mac_address() to check if the given mac
address is valid and set also dev_addr of the net_device.
Check also the return value of ethoc_set_mac_address() in
ethoc_probe().

Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.

v2: set net_device->dev_addr in ethoc_set_mac_address(),
    check if given address is valid
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>

Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.

Remove dev_addr in interface_setup(), it's not needed anymore.

Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.

v2: use bitops, adapt to eth_hw_addr_random()
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reset the state of addr_assign_type to NET_ADDR_PERM as soon as
the MAC get changed via .ndo_set_mac_address.

v2: use bitops to reset addr_assign_type
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.

Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.

v2: reworked to prevent using an extra variable
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.

Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.

Remove one memcpy from emac_dev_setmac_addr() since this is a
duplicate: it's already done some lines above.

v2: use bitops, adapt to eth_hw_addr_random, remove a memcpy
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set addr_assign_type correctly to NET_ADDR_RANDOM in case
a random MAC address was generated and assigned to the netdevice.

v2: added comment, renamed bool variable to random_mac
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.

v2: adapt to eth_hw_addr_random()
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some controllers have TSU. It can register one VLAN tag, and it can
filter other VLAN tag by hardware.
If vlan_rx_add_vid() is called twice or more, the driver will disable
the filtering.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some controllers have TSU. It can filter multicast by hardware.
This patch supports it.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the controller has TSU, the each channel needs TSU registers.
This patch also fixes the iounmap condition in the sh_eth_drv_remove().
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SH7757 has 2 Fast Ethernet and 2 Gigabit Ethernet, and the first
Gigabit channel needs the initialization. So, this patch adds the
parameter of "needs_init", and if the sh_eth_plat_data is set it
to 1, the driver will initialize the channel.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SH7757's GETHER has TSU registers. So, this patch adds the value
of ".tsu = 1" in the sh_eth_cpu_data.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Both translation tables and network coding use timeouts to do house
keeping, so we might as well share the function used to compare a
timestamp+timeout with current time.

For readability and simplicity, the function is renamed to
has_timed_out() and uses time_is_before_jiffies() instead of
time_after().
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Most of the values in that call are derived from the skb, so we can hand
over the skb instead.
Reported-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

All batman-adv packets have a common 3 byte header. It can be used to share
some code between different code paths, but it was never explicit stated that
this header has to be always the same for all packets. Therefore, new code
changes always have the problem that they may accidently introduce regressions
by moving some elements around.

A new structure is introduced that contains the common header and makes it
easier visible that these 3 bytes have to be the same for all on-wire packets.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

(ttvn == 0) is currently used as initial condition. However this is not a good
idea because ttvn gets the vale zero each time after reaching the maximum value
(wrap around). For this reason a new flag is added in order to define whether a
node has an initialised table or not. Moreover, after invoking
tt_global_del_orig(), tt_initialised has to be set to false
Reported-by: NAlexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Tested-by: NAlexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register.  These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.

We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.

There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF.  Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.

The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.

This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Each port has a block of 64-bit SRAM that is divided between buffer
table and descriptor cache regions at initialisation time.  Currently
we use a fixed allocation, but it needs to be changed to support
larger numbers of queues.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

This lets us identify the NIC affected in case of failure, and
will be necessary to adjust for SR-IOV constraints.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Abstract some of the channel operations to allow for 'extra'
channels that do not have RX or TX queues.

- Try to assign a channel to each extra channel type that is enabled
  for the NIC, but gracefully degrade if we can't allocate sufficient
  MSI-X vectors
- Allow each extra channel type to generate its own channel name
- Allow channel types to disable reallocation and reinitialisation
  of their channels
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The TX DMA engine issues upstream read requests when there is room in
the TX FIFO for the completion. However, the fetches for the rest of
the packet might be delayed by any back pressure.  Since a flush must
wait for an EOP, the entire flush may be delayed by back pressure.

Mitigate this by disabling flow control before the flushes are
started.  Since PF and VF flushes run in parallel introduce
fc_disable, a reference count of the number of flushes outstanding.

The same principle could be applied to Falcon, but that
would bring with it its own testing.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

For SR-IOV we will need to send events to event queues that belong to
VFs serviced by other drivers.  Change the parameters of
efx_generate_event() to allow this and declare it extern.

While we're at it, remove the existing declaration under the wrong
name efx_nic_generate_event().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

When SR-IOV is enabled we may receive FLR (Function-Level Reset)
events, associated queue flush events and requests from VF drivers at
any time.  Therefore we need to keep event queues and interrupts
enabled whenever possible.

Currently we stop interrupt-driven event processing before flushing RX
and TX queues; efx_nic_flush_queues() then polls event queues for
flush events and discards any others it finds.  Change it to work with
the regular event handling functions.

Currently efx_start_channel() fills RX queues synchronously when a
device is brought up.  This could now race with NAPI, so change it to
send fill events.

This was almost entirely written by Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

This makes it harder to accidentally send such events to TX-only
channels.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The RMFT_DEST_MAC and TMFT_SRC_MAC register fields were previously
documented as 44 bits wide, whereas a MAC address has 48 bits.
Thankfully the hardware uses the correct width and the driver has
used separate definitions that divide each of these into 32-bit and
16-bit fields.

Fix the initial definitions for these fields and rewrite the latter
definitions to use them.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

On Siena each TX queue can be configured to send only packets for
which there is a TX MAC filter that matches the source MAC address,
queue ID, and optionally VID.  This will be used to implement the
'spoofchk' feature for SR-IOV virtual functions.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

On Siena all received packets that don't match a more specific filter
will match the unicast or multicast default filter.  Currently we
leave these set to the default values (RSS with base queue number of
0).  Allow them to be reconfigured to select a single RX queue.

These default filters are programmed through the FILTER_CTL register,
but we represent them internally as an additional table of size 2.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>