This patch creates a new driver, sierra.c, that supports the new
non-composite Sierra Wireless WWAN devices. The older Sierra
Wireless and Airprime devices are supported in airprime.c.
Signed-off-by: NKevin Lloyd  <linux@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

coverity spotted (id #185) that we still use urb, if the allocation
fails in the error path. This patch fixes this by returning directly.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move variables only used on !__hppa__ into that #ifndef section. This
cleans up a compiler warning on parisc. Problem pointed out by
Joel Soete.
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch limits the amount of outstanding 'write' data that can be
queued up for the ftdi_sio driver, to prevent userspace DoS attacks (or
simple accidents) that use up all the system memory by writing lots of
data to the serial port.

The original patch was by Guillaume Autran, who in turn based it on the
same mechanism implemented in the 'visor' driver.  I (Ian Abbott)
re-targeted the patch to the latest sources, fixed a couple of errors,
renamed his new structure members, and updated the implementations of
the 'write_room' and 'chars_in_buffer' methods to take account of the
number of outstanding 'write' bytes.  It seems to work fine, though at
low baud rates it is still possible to queue up an amount of data that
takes an age to shift (a job for another day!).
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The anti user-DoS mechanism in the USB serial 'visor' driver can fail in
the following way:

visor_open: priv->outstanding_urbs = 0
visor_write: ++priv->outstanding_urbs
visor_close:
visor_open: priv->outstanding_urbs = 0
visor_write_bulk_callback: --priv->outstanding_urbs

So priv->outstanding_urbs ends up as (unsigned long)(-1).  Not good!

I haven't seen this happen with the visor driver as I don't have the
hardware, but I have seen it while testing a patch to implement the same
functionality in the ftdi_sio driver (patch not yet submitted).

The fix is pretty simple: don't reinitialize outstanding_urbs in
visor_open.  (Again, I haven't tested the fix in visor, but I have
tested it in ftdi_sio.)
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the kernel version to the usb-storage Protocol/SubClass
unneeded message in order to help us troubleshoot such problems.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a US_FL_MAX_SECTORS_64 and removes the Genesys special-cases
for this that were in scsiglue.c. It also adds the flag to other devices
reported to need it.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as731) makes a couple of small fixes to the hub_port_resume
routine:

	Don't return status >= 0 when an error occurs;

	Clear the port-change-suspend status indicator after
	resuming a device.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as730) contains an unusual_devs entry for a Samsung MP3
device.

From: Ernis <ernisv@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as725) adds an unusual_devs entry for the Motorola RAZR V3x.

From: Davide Perini <perini.davide@dpsoftware.org>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

finish_device_resume() in the hub driver isn't careful always to return
a negative code in all the error pathways.  It also doesn't return 0 in
all the success pathways.  This patch (as724) fixes the behavior.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My recent patch converting usb-storage to use
usb_reset_composite_device() added a bug, a race between reset and
disconnect.  It was necessary to drop the private lock while executing a
reset, and if a disconnect occurs at that time it will cause a crash.

This patch (as722) fixes the problem by explicitly checking for an early
termination after executing each command.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this adds
better debugging output &
an update of the quirk list
to the acm driver
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a new driver for the Cypress CY7C63xxx mirco controller series.
It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus
GmbH.  It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I
ported to kernel 2.6 using sysfs. I intend to support more controllers
of this family (and more features) as soon as I get hold of the required
IDs etc. Please see the source code's header for more information.
Signed-off-by: NOliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usbfs stores the wrong signal number in the siginfo structure used for
notifying user programs about device disconnect.  This patch (as726)
fixes it.

From: Zoran Marceta <Zoran.Marceta@micronasnit.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Susteen Datapilot cable
(http://www.susteen.com/productdetail/71/producthl/Notempty) has an
internal pl2303 to communicate with a set of dummy connector-ends that
connect to a variety of cell phones. I've found that it works right out
of the box by simply adding the product/vendor id to the pl2303 driver.
Signed-off-by: NMatt Meno <mmeno@idealcorp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes blatant leaks in visor driver and makes it report
mode sensible things in ->write_room (this is only needed if your visor
is a terminal though).

It is made to fit into 80 columns with a temporary variable.
Might even save a few instructions...
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fix addresses two issues:
- Unattached port structures were not freed
- My initial fix for crash when eventd runs a work in a freed port
  did not go far enough
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I noticed this while debugging something unrelated on
sparc64.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Text from the back of the box, for your information/amusement:

 USB DATA CABLE
   FOR K700 Series

 The USB Cable is an ideal link between your mobile phone and PC. Employing
 the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions
 such as synchronization of phone book and calendar,as well as Internet browsing via
 a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity.

 MADE IN CHINA

From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds OHCI glue bits for the USB host interface in the
Cirrus ep93xx (arm920t) CPU.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I received an DBAU1200 eval kit from AMD a few days ago and tried to
enable the USB2 port, but the current linux-2.6 GIT did not even
compile with CONFIG_SOC_1200, CONFIG_SOC_AU1X00, CONFIG_USB_EHCI and
CONFIG_USB_OHCI set.
Furthermore, in ehci-hcd.c, platform_driver_register() was called with
an improper argument of type 'struct device_driver *' which of course
ended up in a kernel oops. How could that ever have worked on your
machines?

Anyway, here's a trivial patch that makes the USB subsystem working
on my board for both OHCI and EHCI.
It also removes the /* FIXME use "struct platform_driver" */.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Compile fixes for au1200 ohci.

First part looks a bit hackish... but it works for me.
Signed-off-by: NDomen Puncer <domen.puncer@ultra.si>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.

To fix this three things are needed.

#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports

The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.

The actual chip setup done by the quirk is the precise setup recommended
by the vendor.

(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: NAlan Cox <alan@redhat.com>
Acked-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Joseph Fannin reported that hpet_rtc_interrupt() enables hardirqs
in irq context:

[   25.628000]  [<c014af4e>] trace_hardirqs_on+0xce/0x200
[   25.628000]  [<c036cf21>] _spin_unlock_irq+0x31/0x70
[   25.628000]  [<c0296584>] rtc_get_rtc_time+0x44/0x1a0
[   25.628000]  [<c01198bb>] hpet_rtc_interrupt+0x21b/0x280
[   25.628000]  [<c0161141>] handle_IRQ_event+0x31/0x70
[   25.628000]  [<c0162d37>] handle_edge_irq+0xe7/0x210
[   25.628000]  [<c0106192>] do_IRQ+0x92/0x120
[   25.628000]  [<c0104121>] common_interrupt+0x25/0x2c

the call of rtc_get_rtc_time() is highly suspect. At a minimum we
need the patch below to save/restore hardirq state.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Joseph Fannin <jfannin@gmail.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It looks like someone confused kmem_cache_create with a different allocator
and was attempting to give it knowledge of how many cache entries there
were.

With the unfortunate result that each slab entry was big enough to hold
every irq.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is confirmed to fix a hang due to PCI resource conflicts with
setting up the Cardbus bridge on old laptops with the 440MX chipsets.
Original report by Alessio Sangalli, lspci debugging help by Pekka
Enberg, and trial patch suggested by Daniel Ritz:

  "From the docs available i would _guess_ this thing is really similar
   to the 82443BX/82371AB combination.  at least the SMBus base address
   register is hidden at the very same place (32bit at 0x90 in function
   3 of the "south" brigde)"

The dang thing is largely undocumented, but the patch was corroborated
by Asit Mallick:

  "I am trying to find the register information. 440MX is an integration of
   440BX north-bridge without AGP and PIIX4E (82371EB).  PIIX4 quirk
   should cover the ACPI and SMBus related I/O registers."

and verified to fix the problem by Alessio.

Cc: Daniel Ritz <daniel.ritz-ml@swissonline.ch>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Tested-by: NAlessio Sangalli <alesan@manoweb.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

1. Multipath devices for which SetPGID is not supported are not handled well.
   Use NOP ccws for path verification (sans path grouping) when SetPGID is not
   supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
   first one) and try to find a common one. Moan if no common PGID can be
   found (and use NOP verification). If no PGIDs have been set, use the css
   global PGID (as before). (Rationale: SetPGID will get a command reject if
   the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
   will remove the old PGIDs. rcp will generate solicited CRWs which can be
   savely ignored by the machine check handler (all other actions create
   unsolicited CRWs).
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The module parameters for xpram are not or in a wrong way parsed.
The xpram module uses the module_param_array directive with an int
parameter which causes the kernel to automatically parse the passed
numbers. This will cause errors if arguments are omitted or cause
wrong results if arguments have size qualifiers.
Use module_param_array with charp and parse the arguments later.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add a reg_mutex to prevent unregistering a subchannel before it has been
registered. Since 2.6.17, we've seen oopses in kslowcrw when a device is
found to be not operational during sense id when doing initial device
recognition; it is not clear yet why that particular problem was not (yet)
observed with earlier kernels...
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

No need for video to be always in
No need for smart battery driver to be always in
Acked-by: NLen Brown <len.brown@intel.com>
Cc: linux-acpi@vger.kernel.org
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Bpqether is encapsulating AX.25 frames into ethernet frames.  There is a
virtual bpqether device paired with each ethernet devices, so it's normal
to pass through dev_queue_xmit twice for each frame which triggers the
locking detector.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a proper prototype for i2o_parm_issue() in core.h.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently the snsc driver uses force_sig to send init a SIGPWR when the
system overheats.  This patch switches it to kill_proc instead which has
the following advantages:

 (1) gets rid of one of the last remaining tasklist_lock users
     in modular code
 (2) simplifies the snsc code significantly

The downside is that an init implementation could in theory block SIGPWR
and it would not get delivered.  The sysvinit code used by all major
distributions doesn't do this and blocking this signal in init would be a
rather stupid thing to do.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Switch from register_chrdev() to   (register|alloc)_chrdev_region().

- use a cdev.  This was intended for original patchset, but was
  overlooked.

  We use a single cdev for all pins (minor device-numbers), as gleaned
  from cs5535_gpio, and in contrast to whats currently done in scx200_gpio
  (which I'll fix soon)
Signed-off-by: NJim Cromie <jim.cromie@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix module-init-func by repairing usage of platform_device_del/put in
module-exit-func.  IOW, it imitates Ingo's 'mishaps' patch, which fixed the
module-init-func's undo handling.

Also fixes lack of release_region to undo the earlier registration.

Also starts to 'use a cdev' which was originally intended (its present in
scx200_gpio).  Code compiles and runs, exhibits a lesser error than
previously.  (re-register-chrdev fails)

Since I had to add "include <linux/cdev.h>", I went ahead and made 2
tweaks that fell into diff-context-window:
- remove include <linux/config.h>      everyone's doing it
- copyright updates - current date is 'wrong'
Signed-off-by: NJim Cromie <jim.cromie@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>