Some hardware crypto drivers register asynchronous ctr(aes), which is left
unused in IPSEC because rfc3686 template only supports synchronous block
ciphers. Some other drivers register rfc3686(ctr(aes)) to workaround this
limitation but not all.

This patch changes rfc3686 to use asynchronous block ciphers, to allow async
ctr(aes) algorithms to be utilized automatically by IPSEC.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

IPSEC uses block ciphers asynchronous, but probes only for synchronous block
ciphers and makes ealg entries only available if synchronous block cipher is
found. So with setup, where hardware crypto driver registers asynchronous
block ciphers and software crypto module is not build, ealg is not marked
as being available.

Use crypto_has_ablkcipher instead and remove ASYNC mask.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

Remove the check if x->km.state equal to XFRM_STATE_VALID in
xfrm_state_check_expire(), which will be done before call
xfrm_state_check_expire().

add a LINUX_MIB_XFRMOUTSTATEINVALID statistic to record the
outbound error due to invalid xfrm state.
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

We threw away the microchannel support, but the removal wasn't
completely trivial since there was namespace overlap with the
machine check support, and hence some orphaned dependencies
survived the deletion.  This attempts to sweep those up and
send them to the bit-bucket.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fields must be null-terminated.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As per suggestion from Eric Dumazet this patch makes tcp_ecn sysctl
namespace aware.  The reason behind this patch is to ease the testing
of ecn problems on the internet and allows applications to tune their
own use of ecn.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

splice() can handle pages of any order, but network code tries hard to
split them in PAGE_SIZE units. Not quite successfully anyway, as
__splice_segment() assumed poff < PAGE_SIZE. This is true for
the skb->data part, not necessarily for the fragments.

This patch removes this logic to give the pages as they are in the skb.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case user passed address via netlink during create, NET_ADDR_PERM was set.
That is not correct so fix this by setting NET_ADDR_SET.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function ethoc_set_mac_address() was incorrectly using passed pointer as
pointer to address, that is not correct.
Struct sockaddr have to be be used here.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit de0a4148 added Kconfig logic to
select HWMON and removed all the IS_ENABLED(CONFIG_HWMON) checks in the
tg3.c file. It missed this one check in the header.

Update version to 3.129 and update copyright year.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the code to detect PCI function number on 5717, 5719, and 5720.
If shared memory does not have proper signature, read the function number
from register directly.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Detect NVRAM types for 5762 and read OTP firmware version.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic support for 5762 which is a 57765_PLUS class device.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the size of skb allocated for NDISC is MAX_HEADER +
LL_RESERVED_SPACE(dev) + packet length + dev->needed_tailroom,
but only LL_RESERVED_SPACE(dev) bytes is "reserved" for headers.
As a result, the skb looks like this (after construction of the
message):

head       data                   tail                       end
+--------------------------------------------------------------+
+           |                      |          |                |
+--------------------------------------------------------------+
|<-hlen---->|<---ipv6 packet------>|<--tlen-->|<--MAX_HEADER-->|
    =LL_                               = dev
     RESERVED_                           ->needed_
     SPACE(dev)                            tailroom

As the name implies, "MAX_HEADER" is used for headers, and should
be "reserved" in prior to packet construction.  Or, if some space
is really required at the tail of ther skb, it should be
explicitly documented.

We have several option after construction of NDISC message:

Option 1:

head       data                   tail       end
+---------------------------------------------+
+           |                      |          |
+---------------------------------------------+
|<-hlen---->|<---ipv6 packet------>|<--tlen-->|
   =LL_                                = dev
    RESERVED_                           ->needed_
    SPACE(dev)                            tailroom

Option 2:

head            data                   tail       end
+--------------------------------------------------+
+                |                      |          |
+--------------------------------------------------+
|<--MAX_HEADER-->|<---ipv6 packet------>|<--tlen-->|
                                            = dev
                                             ->needed_
                                               tailroom

Option 3:

head                        data                   tail       end
+--------------------------------------------------------------+
+                |           |                      |          |
+--------------------------------------------------------------+
|<--MAX_HEADER-->|<-hlen---->|<---ipv6 packet------>|<--tlen-->|
                    =LL_                                = dev
                     RESERVED_                          ->needed_
                     SPACE(dev)                           tailroom

Our tunnel drivers try expanding headroom and the space for tunnel
encapsulation was not a mandatory space -- so we are not seeing
bugs here --, but just for optimization for performance critial
situations.

Since NDISC messages are not performance critical unlike TCP,
and as we know outgoing device, LL_RESERVED_SPACE(dev) should be
just enough for the device in most (if not all) cases:
  LL_RESERVED_SPACE(dev) <= LL_MAX_HEADER <= MAX_HEADER
Note that LL_RESERVED_SPACE(dev) is also enough for NDISC over
SIT (e.g., ISATAP).

So, I think Option 1 is just fine here.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MX6 and mx28 support enhanced DMA descriptor buff to support 1588
ptp. But MX25, MX3x, MX5x can't support enhanced DMA descriptor buff.
Check fec type and choose correct DMA descriptor buff type.

Remove static config CONFIG_FEC_PTP.
ptp function will be auto detected.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sparse complains that:
drivers/net/ethernet/broadcom/tg3.c:5670:55: sparse: constant
0x7fffffffffffffff is so big it is long long (on x86/32 bit)

so we suffix the constant with LL in the header file.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables USB dynamic autosuspend for LAN9500A.  This
saves very little power in itself, but it allows power saving
in upstream hubs/hosts.

The earlier devices in this family (LAN9500/9512/9514) do not
support this feature.
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register read/write functions already log a warning if
an access fails, so this patch removes the additional warnings
logged by callers that don't add any more information.

This patch makes the resulting driver smaller by not containing
as many warning strings.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
This is a V6 of a repost of my previous patchset:
"[patch net-next v2 00/15] net: introduce upper device lists and remove dev->master" from Aug 14

The discussion around
"[net-next] bonding: don't allow the master to become its slave"
forced me to think about upper<->lower device connections.

This patchset adds a possibility to record upper device linkage.
All upper<->lower devices are converted to use this mechanism right after.
That leads to dev->master removal because this info becomes redundant since
"master links" have the same value.

After all changes, there is no longer possible to do things as:
"bond->someotherdevice->samebond"

Also I think that drivers like cxgb3, qlcnic, qeth would benefit by this
in future by being able to get more appropriate info about l3 addresses.

v5->v6:
- netdev_has_upper_dev() - added statement to comment that this is looking at
  the immediate upper devices only.
- renamed "RTNL semaphore" -> "RTNL lock" in all comments
- renamed __netdev_has_upper_dev() to __netdev_search_upper_dev() to emhasize
  the difference to netdev_has_upper_dev()

v4->v5:
- fixed missed typo in drivers/infiniband/hw/nes/nes_cm.c

v3->v4:
- comments in __netdev_upper_dev_link() squashed into one line
- kfree_rcu used instead of call_rcu in netdev_upper_dev_unlink()

v2->v3:
- removed recursion in __netdev_has_upper_dev()
- refreshed bits to be applicable on current net-next

v1->v2:
- s/unique/master/ better naming + stays closer to the past
- fixed vlan err goto
- original patch 15 (WARN_ON change) is squashed into the first patch
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nobody uses this now. Remove it.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Benefit from new upper dev list and free bonding from dev->master usage.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also, since all users call __vlan_find_dev_deep() with rcu_read_lock,
make no possibility to call this with rtnl mutex held only.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also benefit from rcu_read_lock held and use __in_dev_get_rcu() in ipv4 case.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rcu_read_lock was missing here
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This lists are supposed to serve for storing pointers to all upper devices.
Eventually it will replace dev->master pointer which is used for
bonding, bridge, team but it cannot be used for vlan, macvlan where
there might be multiple upper present. In case the upper link is
replacement for dev->master, it is marked with "master" flag.

New upper device list resolves this limitation. Also, the information
stored in lists is used for preventing looping setups like
"bond->somethingelse->samebond"
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, when invalid address was passed to ndo_set_mac_address,
random mac was generated and set. Fix this by returning -EADDRNOTAVAIL
in this situation.

Also polish the code around a bit.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also remove unused "mac" from uml_net struct.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>