Add a memory node, with an empty memory size, which will be filled
by the bootloader.

This is done in preparation for removing the memory node from
imx6qdl.dtsi.
Reported-by: NMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.
Reported-by: NMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NMarco Franchi <marco.franchi@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

On the vf610-zii-scu4-aib board there is a hi8435 (32-channel
discrete-to-digital SPI sensor device) in the DSPI0 bus.

Add support for it.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add egalax touch screen support on i2c2 bus, it is connected
to LVDS0, while the existing one on i2c3 bus is connected to
LVDS1.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add stop-mode property which is required by stop mode wakeup
feature.
Signed-off-by: NAisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add stop-mode property which is required by stop mode wakeup
feature.
Signed-off-by: NAisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add stop-mode property which is required by stop mode wakeup
feature.
Signed-off-by: NAisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add stop-mode property which is required by stop mode wakeup
feature.
Signed-off-by: NAisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The imx6ul-pico-pi contains a imx6ul-pico SoM and a pi baseboard:
https://www.technexion.com/products/pico-baseboards/detail/PICO-PI

Add support for it.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This adds following peripherals support:

 - ADC
 - GPIO LED
 - GPIOs
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Use the same child led node and label name as used in the
imx7d-pico-hobbit board.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx6ul-pico-hobbit board contains:

- One SoM board (imx6ul pico)
- One base board (hobbit).

In order to make it easier for adding support for other board variants,
move the commom SoM part to the imx6ul-pico.dtsi file.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

add the qDMA device tree nodes for LS1021A devices.
Signed-off-by: NWen He <wen.he_1@nxp.com>
Signed-off-by: NPeng Ma <peng.ma@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boards based on vf500/vf600 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the vf500.dtsi/vf610m4.dtsi files.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The GIC_CPU_MASK_SIMPLE() macro should take as its argument the actual
number of CPU cores the interrupt controller is wired to.

i.MX7S contains a single Cortex-A7, hence the second interrupt specifier
cell for Private Peripheral Interrupts should use "GIC_CPU_MASK_SIMPLE(1)".

Likewise, i.MX7D contains two Cortex-A7 cores, so it should use
"GIC_CPU_MASK_SIMPLE(2)" instead.

Tested on a imx7s-warp.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The GIC_CPU_MASK_SIMPLE() macro should take as its argument the actual
number of CPU cores the interrupt controller is wired to.

i.MX6UL contains a single Cortex-A7, hence the second interrupt specifier
cell for Private Peripheral Interrupts should use "GIC_CPU_MASK_SIMPLE(1)".

Tested on a imx6ul-evk.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The flexcan1 is pin conflict with fec. User would make flexcan1 enabled
with fec disabled to use CAN.
Signed-off-by: NAisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The CAN transceiver on MX6SX Sabreauto board seems in sleep mode by default
after power up the board. User has to press the wakeup key on ARD baseboard
before using the transceiver, or it may not work properly when power up the
board at the first time(warm reset does not have such issue).

This patch operates the wake pin too besides stby/en pins by chaining them
together in regulator mode.
Signed-off-by: NAisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

CAN transceiver is different on RevA and RevB board.
It's active high on RevA while active low on Rev B.
Signed-off-by: NAisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The LS1021A has 8 possible PWMs, so adding them (disabled by default)
Signed-off-by: NPatrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The ConnectCore 6UL SBC Pro has an AUO/Goodix LCD accessory kit that is
connected on the LVDS interface through an on-board LVDS transceiver.

This change adds support for the touch interface.
Signed-off-by: NAlex Gonzalez <alex.gonzalez@digi.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This change adds support for the AUO G101EVN010 lcdif panel for the
mxsfb DRM driver.
Signed-off-by: NAlex Gonzalez <alex.gonzalez@digi.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boards based on imx25 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx25.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boards based on imx27 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx27.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boards based on imx1 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx1.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boards based on imx28 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx28.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boards based on imx23 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx23.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.

Most of the i.MX NXP reference board dts files have already been
converted, so switch the remaining ones.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.

Most of the wandboard dts files have already been converted, so switch
the remaining ones.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx50-evk has duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx50.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

i.MX6SLL EVK board has WDOG_B pin connected to the PMIC;

Add the WDOG_B pinctrl entry and 'fsl,ext-reset-output'
property to wdog node to let watchdog trigger a system
POR reset via the PMIC.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

On i.MX6SLL EVK board, there is a debug LED controlled
by MX6SLL_PAD_EPDC_VCOM1__GPIO2_IO04 pin, add support
for it.
Signed-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The imx6qdl-sabreauto boards have a pcie slot so let's enable it.

Tested on imx6dl-sabreauto with an atk9k wifi card; scanning works.

There are unhandled differences for imx6qp but imx6qp-sabreauto.dts
already contains a snippet explicitly disabling the &pcie node so that
can be dealt with later.
Signed-off-by: NLeonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boards based on imx6sl have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx6sl.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boards based on imx6sx have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx6sx.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boards based on imx6ul have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx6ul.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: NRob Herring <robh@kernel.org>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add memory node to board dts.

This is done in preparation of removing the memory node from imx6ul.dtsi.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>